Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected via LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No. DTC Detection Condition Trouble Area
B1532 When any of the following conditions is met:
·

Video signal (digital) is lost

·

Navigation ECU is not connected while the power switch is on (ACC) or on (IG)

·

Communication between the radio and display receiver assembly and the navigation ECU is not possible when the engine is started


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

No. 1 navigation wire



HINT:

Even if no malfunction is present, this DTC may be stored depending on the auxiliary battery condition or hybrid control system start voltage.


WIRING DIAGRAM

E276665E40
0.917,2.323 2.104,2.729 1.188,0.406 10 false Radio and Display Receiver Assembly 5.219,2.323 6.396,2.677 1.177,0.354 10 false Navigation ECU 2.208,0.698 2.438,0.885 0.229,0.188 10 false Y2 2.271,0.51 2.5,0.698 0.229,0.188 10 false 4 2.26,0.917 2.49,1.104 0.229,0.188 10 false 3 2.26,1.313 2.49,1.5 0.229,0.188 10 false 8 2.26,1.708 2.49,1.896 0.229,0.188 10 false 1 4.885,0.51 5.115,0.698 0.229,0.188 10 false 4 4.885,0.917 5.115,1.104 0.229,0.188 10 false 3 4.885,1.313 5.115,1.5 0.229,0.188 10 false 2 4.875,1.708 5.104,1.896 0.229,0.188 10 false 1 1.781,0.708 2.083,0.927 0.302,0.219 10 false +B2 5.167,0.708 5.563,0.969 0.396,0.26 10 false +B 1.708,1.094 2.115,1.292 0.406,0.198 10 false ACC2 5.177,1.083 5.583,1.281 0.406,0.198 10 false ACC 1.698,1.49 2.104,1.688 0.406,0.198 10 false GND2 5.167,1.479 5.729,1.708 0.563,0.229 10 false GND 1.75,1.885 2.156,2.083 0.406,0.198 10 false GVIF 2.979,2.875 4.74,3.063 1.76,0.188 10 false : LVDS Communication Line 3.5,0.979 3.813,1.177 0.313,0.198 10 false * 3.5,0.583 3.813,0.781 0.313,0.198 10 false * 3.5,1.75 3.813,1.948 0.313,0.198 10 false * 3.5,1.385 3.813,1.583 0.313,0.198 10 false * 2.927,3.292 5.156,3.542 2.229,0.25 10 false *: No. 1 Navigation Wire 2.219,1.094 2.448,1.281 0.229,0.188 10 false Y2 2.208,1.479 2.438,1.667 0.229,0.188 10 false Y2 2.208,1.885 2.438,2.073 0.229,0.188 10 false Y1 4.833,0.688 5.063,0.875 0.229,0.188 10 false Y3 4.823,1.094 5.052,1.281 0.229,0.188 10 false Y3 4.833,1.479 5.063,1.667 0.229,0.188 10 false Y3 4.833,1.885 5.063,2.073 0.229,0.188 10 false Y4 5.177,1.896 5.583,2.094 0.406,0.198 10 false GVIF

PROCEDURE

1.CHECK NO. 1 NAVIGATION WIRE (NAVIGATION ECU POWER SOURCE)
a.

Disconnect the Y3 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y3-1 (B+) - Y3-2 (GND) Power switch off 11 to 14 V
Y3-3 (ACC) - Y3-2 (GND) Power switch on (ACC) 11 to 14 V




OK

2.REPLACE NO. 1 NAVIGATION WIRE

NG

4.CHECK NO. 1 NAVIGATION WIRE
2.REPLACE NO. 1 NAVIGATION WIRE
a.

Replace the No. 1 navigation wire with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

3.REPLACE NAVIGATION ECU
3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK NO. 1 NAVIGATION WIRE
a.

Disconnect the Y2 radio and display receiver assembly connector.


b.

Disconnect the Y3 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Condition Specified Condition
Y2-4 (+B2) - Y3-1 (B+) Always Below 1 Ω
Y2-3 (ACC2) - Y3-3 (ACC) Always Below 1 Ω
Y2-8 (GND2) - Y3-2 (GND) Always Below 1 Ω
Y2-4 (+B2) - Body ground Always 10 kΩ or higher
Y2-3 (ACC2) - Body ground Always 10 kΩ or higher
Y2-8 (GND2) - Body ground Always 10 kΩ or higher




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG