Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop. A
Automatic station search function stops on a station. B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed. A
Optional components are installed. B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK NAVIGATION RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E245523

Preparation for check

i.

Remove the antenna connector from the navigation receiver assembly.



b.

Check for noise

i.

Turn the power switch on (ACC) with the navigation receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.





OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the RA navigation receiver assembly connector.


b.
U111431E01
0.095,0.056 0.274,0.221 0.179,0.165 10 *a 0.624,1.017 0.847,1.180 0.223,0.162 10 RA 0.838,1.477 1.232,1.645 0.393,0.167 10 ANT+ 1.538,1.096 1.136,1.443 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Power switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V


Text in Illustration
*a Component without harness connected
(Navigation Receiver Assembly)



OK

5.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

5.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

END

NG

6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

END

NG

7.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
7.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA(for Roof)>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

END

NG

8.REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY
8.REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

END

NG