Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly.

DTC No. DTC Detection Condition Trouble Area
B15D3 When either of the following conditions is met:
·

The stereo component amplifier assembly is/was not connected while the power switch is/was on (ACC) or (IG)

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between navigation receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:

The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E286973E14
0.51,0.375 1.5,0.823 0.99,0.448 10 false from Auxiliary Battery 0.375,1.531 2.208,1.729 1.833,0.198 10 false from ACC Relay 2.958,0.531 3.375,0.76 0.417,0.229 10 false AMP 2.813,1.677 4.646,1.875 1.833,0.198 10 false ECU-ACC 2.167,2.958 2.521,3.177 0.354,0.219 10 false L38 2.167,3.125 4.302,3.49 2.135,0.365 10 false Navigation Receiver Assembly 5.438,4.021 6.646,4.531 1.208,0.51 10 false Stereo Component Amplifier Assembly 1.104,4.188 3.24,4.552 2.135,0.365 10 false : AVC-LAN Communication Line 3.208,2.271 3.823,2.469 0.615,0.198 10 false TX1+ 3.219,2.677 3.833,2.875 0.615,0.198 10 false TX1- 5.219,0.385 5.833,0.583 0.615,0.198 10 false L30 5.208,0.958 5.823,1.156 0.615,0.198 10 false L30 5.219,1.531 5.833,1.729 0.615,0.198 10 false L31 5.219,2.292 5.833,2.49 0.615,0.198 10 false L31 5.219,2.677 5.833,2.875 0.615,0.198 10 false L31 5.219,3.219 5.833,3.417 0.615,0.198 10 false L30 5.229,3.646 5.844,3.844 0.615,0.198 10 false L30 5.615,0.385 6.229,0.583 0.615,0.198 10 false +B 5.615,0.948 6.229,1.146 0.615,0.198 10 false +B2 5.635,1.521 6.25,1.719 0.615,0.198 10 false ACC 5.625,2.271 6.24,2.469 0.615,0.198 10 false TX+ 5.635,2.688 6.25,2.885 0.615,0.198 10 false TX- 5.625,3.219 6.24,3.417 0.615,0.198 10 false GND 5.625,3.635 6.24,3.833 0.615,0.198 10 false GND2 5.313,0.188 5.927,0.385 0.615,0.198 10 false 1 5.271,0.75 5.885,0.948 0.615,0.198 10 false 16 5.271,1.333 5.885,1.531 0.615,0.198 10 false 12 5.302,2.073 5.917,2.271 0.615,0.198 10 false 8 5.313,2.49 5.927,2.688 0.615,0.198 10 false 7 5.313,3.01 5.927,3.208 0.615,0.198 10 false 3 5.271,3.438 5.885,3.635 0.615,0.198 10 false 18 3.625,2.146 4.24,2.344 0.615,0.198 10 false 7 3.635,2.531 4.25,2.729 0.615,0.198 10 false 8 0.521,0.917 1.51,1.365 0.99,0.448 10 false from Auxiliary Battery 2.948,1.115 3.365,1.344 0.417,0.229 10 false AMP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

4.CHECK DTC
4.CHECK DTC

b.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the L30 and L31 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-3 (GND) - Body ground Always Below 1 Ω
L30-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L30-1 (+B) - L30-3 (GND) Power switch off 11 to 14 V
L30-16 (+B2) - L30-3 (GND) Power switch off 11 to 14 V
L31-12 (ACC) - L30-3 (GND) Power switch on (ACC) 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-7 (TX1+) - L31-8 (TX+) Always Below 1 Ω
L38-8 (TX1-) - L31-7 (TX-) Always Below 1 Ω
L38-7 (TX1+) - Body ground Always 10 kΩ or higher
L38-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG