Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E300236E05
1.302,1.26 1.917,1.458 0.615,0.198 10 false SNS2 1.76,1.146 2.375,1.344 0.615,0.198 10 false 5 1.292,2.052 1.906,2.25 0.615,0.198 10 false MCO- 1.76,1.938 2.375,2.135 0.615,0.198 10 false 4 5.719,1.26 6.333,1.458 0.615,0.198 10 false SNS2 5.719,2.052 6.333,2.25 0.615,0.198 10 false MIN- 5.542,1.135 6.156,1.333 0.615,0.198 10 false 6 5.479,1.938 6.094,2.135 0.615,0.198 10 false 19 0.479,2.542 1.094,2.74 0.615,0.198 10 false U3 0.469,2.708 2.448,3.094 1.979,0.385 10 false Map Light Assembly (Telephone Microphone Assembly) 5.198,2.521 5.813,2.719 0.615,0.198 10 false L38 5.198,2.688 7.156,3.073 1.958,0.385 10 false Navigation Receiver Assembly

PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
U155182E01
1.533,0.678 1.792,0.833 0.259,0.156 10 L38 0.177,0.162 0.435,0.318 0.259,0.156 10 *a 2.389,2.793 2.789,2.949 0.401,0.156 10 MIN- 2.123,1.99 2.512,2.779 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L38-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L38-6 (SNS2) - Body ground Always 10 kΩ or higher
L38-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly) (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.
E187117E63
0.16,0.067 0.358,0.265 0.198,0.198 10 *a 1.132,1.654 1.548,1.852 0.415,0.198 10 SNS2 2.303,1.654 2.732,1.852 0.429,0.198 10 MCO- 1.776,1.221 1.403,1.641 false 1.909,1.225 2.501,1.641 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SNS2) - 4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

NG

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.


OK:

No DTCs re output.



OK

END

NG

REPLACE MAP LIGHT ASSEMBLY