Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter sub-assembly.

DTC No. DTC Detection Condition Trouble Area
B1324 After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter sub-assembly when the power switch is on (ACC), 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.
·

Combination meter sub-assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E361732E06
1.656,0.427 2.24,0.646 0.583,0.219 10 false MSCH 5.104,0.417 5.688,0.635 0.583,0.219 10 false CNH1 4.896,0.25 5.219,0.479 0.323,0.229 10 false 3 4.906,0.917 5.229,1.146 0.323,0.229 10 false 4 2.156,0.938 2.479,1.167 0.323,0.229 10 false 29 2.146,0.281 2.469,0.51 0.323,0.229 10 false 28 0.896,2.229 3.083,2.583 2.188,0.354 10 false : Local Bus Communication Line 0.604,1.458 1,1.688 0.396,0.229 10 false L27 0.594,1.635 3.26,2.01 2.667,0.375 10 false Combination Meter Sub-assembly 4.531,1.458 5.073,1.688 0.542,0.229 10 false L173*2 4.531,1.625 6.646,2.104 2.115,0.479 10 false Navigation Receiver Assembly 1.667,1.083 2.25,1.302 0.583,0.219 10 false MSCL 5.094,1.073 5.677,1.292 0.583,0.219 10 false CNL1 3.698,2.01 6.292,2.281 2.594,0.271 10 false *1: w/o Intelligent Parking Assist System 4.531,1.292 5.073,1.521 0.542,0.229 10 false L172*1 3.698,2.375 6.396,2.677 2.698,0.302 10 false *2: w/ Intelligent Parking Assist System

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L172 navigation receiver assembly connector (w/o Intelligent Parking Assist System).


b.

Disconnect the L173 navigation receiver assembly connector (w/ Intelligent Parking Assist System).


c.

Disconnect the L27 combination meter sub-assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Intelligent Parking Assist System
Tester Connection Condition Specified Condition
L172-3 (CNH1) - L27-28 (MSCH) Always Below 1 Ω
L172-4 (CNL1) - L27-29 (MSCL) Always Below 1 Ω
L172-3 (CNH1) - Body ground Always 10 kΩ or higher
L172-4 (CNL1) - Body ground Always 10 kΩ or higher
L172-3 (CNH1) - L152-4 (CNL1) Always 10 kΩ or higher

w/ Intelligent Parking Assist System
Tester Connection Condition Specified Condition
L173-3 (CNH1) - L27-28 (MSCH) Always Below 1 Ω
L173-4 (CNL1) - L27-29 (MSCL) Always Below 1 Ω
L173-3 (CNH1) - Body ground Always 10 kΩ or higher
L173-4 (CNL1) - Body ground Always 10 kΩ or higher
L173-3 (CNH1) - L152-4 (CNL1) Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Intelligent Parking Assist System
Tester Connection Condition Specified Condition
L172-3 (CNH1) - Body ground Always Below 1 V
L172-4 (CNL1) - Body ground Always Below 1 V

w/ Intelligent Parking Assist System
Tester Connection Condition Specified Condition
L173-3 (CNH1) - Body ground Always Below 1 V
L173-4 (CNL1) - Body ground Always Below 1 V




OK

2.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER SUB-ASSEMBLY
a.

Remove the combination meter sub-assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.
E305050E08
1.885,1.938 1.635,2.344 false 2.021,1.927 2.219,2.333 false 1.354,2.354 1.823,2.698 0.469,0.344 10 false MSCL 2.146,2.365 2.615,2.708 0.469,0.344 10 false MSCH 0.125,0.49 0.594,0.833 0.469,0.344 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
28 (MSCH) - 29 (MSCL) Always 108 to 132 Ω


Text in Illustration
*a Component without harness connected
(Combination Meter Sub-assembly)



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER SUB-ASSEMBLY

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E286972E02
0.155,0.155 0.467,0.496 0.312,0.341 10 *a 2.323,1.135 2.793,1.476 0.470,0.341 10 CNH1 1.402,1.135 1.872,1.476 0.470,0.341 10 CNL1 2.349,1.339 2.106,1.746 false 1.803,1.336 1.997,1.746 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω


Text in Illustration
*a Component without harness connected
(Navigation Receiver Assembly)



OK

4.REPLACE COMBINATION METER SUB-ASSEMBLY

NG

4.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

5.CHECK METER / GAUGE SYSTEM

NG

5.CHECK METER / GAUGE SYSTEM
a.

Turn the power switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter sub-assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.




OK

END

NG