Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2015.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1612  IG Voltage is Low or High  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that the voltage received by terminal IG is not normal.

DTC No. DTC Detection Condition Trouble Area
C1612
·

IG voltage is low

·

IG voltage is high


·

Harness or connector

·

Parking assist ECU



WIRING DIAGRAM

E222376E59
4.875,1.417 6.167,1.625 1.292,0.208 10 false Parking Assist ECU 4.875,1.26 5.198,1.427 0.323,0.167 10 false L64 5.021,0.333 5.229,0.5 0.208,0.167 10 false IG 5.021,0.771 5.458,0.938 0.438,0.167 10 false GND1 4.833,0.427 4.948,0.615 0.115,0.188 10 false 8 4.833,0.875 4.948,1.063 0.115,0.188 10 false 4 2.417,0.49 3.427,0.656 1.01,0.167 10 false ECU-IG NO. 2 0.323,0.302 1.688,0.469 1.365,0.167 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the radio and display receiver assembly*1 or navigation receiver assembly*2 after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


*1: for Radio and Display Type

*2: for Navigation Receiver Type



PROCEDURE

1.CHECK DTC OUTPUT

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1612 is output A
DTCs are not output B



HINT:

If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU IG VOLTAGE)

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU IG VOLTAGE)
a.
U191344E02
2.604,1.302 2.323,1.302 true 1.427,1.479 1.427,1.865 1.427,1.865 0.823,1.865 true 1.604,0.333 1.938,0.51 0.333,0.177 10 false L64 2.646,1.219 3.094,1.542 0.448,0.323 10 false GND1 0.656,1.781 1.021,2.031 0.365,0.25 10 false IG 0.188,0.073 0.552,0.323 0.365,0.25 10 false *a

Disconnect the L64 parking assist ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-8 (IG) - L64-4 (GND1) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR