Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM D

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  CALIBRATION  


ADJUST INTELLIGENT PARKING ASSIST SYSTEM


a.

This intelligent parking assist system can be adjusted using the diagnostic screen of the radio and display receiver assembly*1 or navigation receiver assembly*2.

*1: for Radio and Display Type

*2: for Navigation Receiver Type



b.

If the following operations are performed, it is necessary to perform adjustments and checks using the diagnostic screen.

Part Name Operation Adjustment Item Proceed to
Spiral cable with sensor sub-assembly
·

Removal and installation of the spiral cable with sensor sub-assembly

·

Removal and installation of the connector of the spiral cable with sensor sub-assembly


Steering angle neutral point (Click here)
Steering angle setting (Click here)
Spiral cable with sensor sub-assembly Replacement Steering angle neutral point (Click here)
Steering angle setting (Click here)
Parking assist ECU Replacement Parking assist ECU initialization PROCEDURE 1
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Height control sensor vehicle height difference setting (HEIGHT SET) PROCEDURE 2
Rear television camera optical axis (CAMERA POSITION SETTING) PROCEDURE 3
Rear television camera assembly
·

Replacement

·

Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.


Rear television camera optical axis (CAMERA POSITION SETTING) PROCEDURE 3
Rear height control sensor sub-assembly RH
·

Replacement

·

Installation position of the rear height control sensor sub-assembly RH changes because of the removal and installation of the rear height control sensor sub-assembly RH


Height control sensor vehicle height difference setting (HEIGHT SET) PROCEDURE 2
Rear television camera optical axis (CAMERA POSITION SETTING) PROCEDURE 3
Lighting system initialization* (Click here)
Rear bumper cover
·

Replacement

·

Installation position of the rear bumper cover changes because of the removal and installation of the rear bumper cover


Rear bumper position (BUMPER) PROCEDURE 4

*: for LED Headlight


HINT:

The adjustment values stored while performing intelligent parking assist system calibration are stored in the parking assist ECU.




PARKING ASSIST ECU INITIALIZATION (PROCEDURE 1)


HINT:

Be sure to check for DTCs before performing this procedure (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).


a.

Preparation for adjustment

i.

Park the vehicle on a level surface with the steering wheel centered.

HINT:

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.



ii.

Adjust the tire pressure to the specified value.


iii.
E187169E01
0.11,0.065 1.270,0.244 1.161,0.179 10 Rear Wheel Side: 2.706,1.976 2.862,2.150 0.156,0.174 10 A 2.414,0.36 3.148,0.699 0.733,0.339 10 Calculation Position 1.044,1.553 1.867,0.439 1.867,0.439 2.323,0.439 false 1.038,2.097 1.382,2.927 1.382,2.927 1.588,2.927 false 1.614,2.842 2.464,3.005 0.850,0.163 10 Center of tire

Measure distance A between the ground and the edge of a rear wheel arch.


iv.

Calculate the difference between distance A and the standard height below.

Standard height:

701 mm (2.30 ft.)


HINT:

Subtract the standard height from the measured value to get the height compensation value. When the measured value is 711 mm: 711 - 701= +10 (height compensation value is +10 mm).



v.

Set a target bar behind the vehicle for optical axis adjustment of the rear television camera.

HINT:

Only when adjusting the optical axis of the camera, create a target bar for adjustment.


E267675E05
4.281,1.698 4.833,1.167 false 2.417,1.698 1.969,1.167 false 3.771,0.333 4.417,0.5 0.646,0.167 10 false *2 4.885,1.083 6.219,1.25 1.333,0.167 10 false *1 1.76,1.063 3.094,1.229 1.333,0.167 10 false *1 3.802,0.75 3.948,0.917 0.146,0.167 10 false B 2.833,0.75 2.979,0.917 0.146,0.167 10 false B 3.938,1.083 4.083,1.25 0.146,0.167 10 false C 2.688,1.083 2.833,1.25 0.146,0.167 10 false C 1.667,1.677 1.813,1.844 0.146,0.167 10 false D 4.958,1.656 5.104,1.823 0.146,0.167 10 false D 3,1.729 3.146,1.896 0.146,0.167 10 false F 3.656,1.729 3.802,1.896 0.146,0.167 10 false F 2.573,2.24 2.719,2.406 0.146,0.167 10 false E 4.083,2.24 4.229,2.406 0.146,0.167 10 false E 6.25,2.375 6.396,2.542 0.146,0.167 10 false A 3.115,3.708 4.021,4.031 0.906,0.323 10 false Vehicle 4.167,3.667 4.75,3.833 0.583,0.167 10 false *3 4,4.125 4.583,4.292 0.583,0.167 10 false *4

Dimension:
A B C D E F
1100 mm
(3.61 ft.)
1600 mm
(5.25 ft.)
30 mm
(1.18 in.)
100 mm
(3.94 in.)
500 mm
(1.64 ft.)
30 mm
(1.18 in.)


Text in Illustration
*1 Target Bar for Camera Adjustment *2 Vehicle Center
*3 Bumper Edge *4 Front Side

HINT:

Check the tape color on the radio and display receiver assembly*1 or navigation receiver assembly*2 and choose a tape color which can be easily seen.

*1: for Radio and Display Type

*2: for Navigation Receiver Type





b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting I" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E305121

Check that "CHK" (red) is not displayed on the "SIGNAL CHECK" screen.

NOTICE:

When "CHK" (red) is displayed for any items except "HT INIT" on the "SIGNAL CHECK" screen, perform inspections using the "SIGNAL CHECK" screen (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DIAGNOSIS SYSTEM).


HINT:

When the screen does not change to the "HEIGHT SET" screen, check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).




c.

HEIGHT SET

NOTICE:
·

HEIGHT SET (entering the height compensation value) must be performed on a level surface.

·

Before performing television camera optical axis adjustment, the height compensation value must be entered using the "HEIGHT SET" screen (Height Control Sensor Vehicle Height Difference Setting).



i.
U191439E02
3.135,0.688 3.323,0.865 0.188,0.177 10 false A

Select indicator A for "HT INIT" on the "SIGNAL CHECK" screen.


ii.
E311251

Press "UP" or "DOWN" to enter the height compensation value calculated previously.

HINT:
·

Positive values are indicated in green and negative values are indicated in red.

·

When the value is shown as "10 MM" in green, it means +10 mm.

·

Available setting range: -102 mm to +102 mm (can be adjusted in 1 mm increments)




iii.

After entering the height compensation value, select "OK". The setting will be stored.

HINT:
·

When "OK" is selected, a beep will sound to confirm that the height compensation value has been stored.

·

The value will not be stored unless "OK" is selected.

·

The value is not stored until the beep has sounded.

·

When "BACK" is selected, the screen changes to SIGNAL CHECK screen without storing the value.

·

Press "OK" with the vehicle in the same condition as when the vehicle height was measured.

·

If a person was in the driver seat when the vehicle height was measured, press "OK" with the same person in the driver seat.

·

On the "SIGNAL CHECK" screen, check that indicator A for "HT INIT" is "OK" (blue).




iv.

Select "NEXT" on the "SIGNAL CHECK" screen.



d.

STEERING ANGLE SETTING

i.
E311256

Perform the "STEERING CENTER MEMORIZE" operation.

·

Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".


HINT:

When performing removal and installation, or replacement of the television camera, steering angle setting is not required.



ii.

Perform the "MAX STEERING ANGLE MEMORIZE" operation.

·

After performing the steering center memorize operation, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the "BACK CAMERA POSITION SETTING" screen.

HINT:
·

It is also possible to start by initially turning the steering to the right side.

·

When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the "STEERING ANGLE SETTING" values have been stored.

·

The values are not stored until the beep has sounded.

·

The values will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel from lock to lock.

·

When "BACK" is selected, the screen changes to the "SIGNAL CHECK" screen without storing any values.

·

The "NEXT" button does not respond until the system memorizes the steering center and maximum steering angle.

·

Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the values to be stored if the steering sensor is malfunctioning.

·

If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the values to be stored after performing the steering angle setting procedure, replace the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).






e.
E214489E05
1.021,1.635 1.667,0.75 1.667,0.75 1.917,0.75 true 2.115,2.625 1.927,2.354 true 1.427,2.635 1.583,2.354 true 0.896,1.563 0.469,1.344 true 2.5,1.667 1.667,0.75 true 2,0.677 3.031,0.99 1.031,0.313 10 false Target bar 1.354,2.677 1.51,2.875 0.156,0.198 10 false A 2.115,2.677 2.271,2.875 0.156,0.198 10 false B 0.313,1.219 0.469,1.417 0.156,0.198 10 false C

BACK CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT)

NOTICE:

Before performing television camera optical axis adjustment, the height compensation value must be entered using the "HEIGHT SET" screen (Height Control Sensor Vehicle Height Difference Setting).


HINT:
·

When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and television camera optical axis adjustment will not be possible.

·

If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE).



i.

Select switches A and B to rotate C so that it is parallel to the target adjustment bar.


ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT) screen.



f.

BACK CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)

i.
E236781E05
0.969,1.552 1.615,0.677 1.615,0.677 2.417,1.542 true 0.833,1.635 1.74,2.625 1.74,2.625 2.552,1.625 true 1.427,2.688 2.25,3 0.823,0.313 10 false Target bar 1.531,0.448 1.781,0.635 0.25,0.188 10 false A

By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars (C) and the corners of the parallelograms (A) match.

E212177E05
5.344,1.583 6,0.583 6,0.583 5.75,0.583 true 5.99,1.802 6.125,1.979 false 4.688,1.427 4.49,1.688 false 0.271,0.188 3.146,0.479 2.875,0.292 10 false Adjustment position for A and target bar: 5,0.49 5.771,0.75 0.771,0.26 10 false Target bar 6.135,1.969 6.375,2.208 0.24,0.24 10 false C 4.396,1.688 4.708,2 0.313,0.313 10 false A 4.76,2.167 6.219,2.448 1.458,0.281 10 false Matching corner C

NOTICE:
·

If the left and right parallelograms (A) and target bars do not match completely, just match the corners of the target bars (C) with the corners of the parallelograms (A).

·

If the left and right parallelograms (A) and the corners of the target bars (C) do not match, make the gaps between each parallelogram (A) and the target bars equal on the left and right sides.

E212178E03
1.125,1.99 0.667,1.26 0.667,1.26 0.885,1.26 true 5.469,1.885 5.313,2.146 false 6.5,2.219 3.479,3.125 3.479,3.125 0.625,2.26 false 1.906,2.146 1.667,1.917 false 6.052,1.99 6.479,1.24 6.479,1.24 6.229,1.24 true 1.938,2.146 2.094,2.344 0.156,0.198 10 false A 5.24,2.208 5.396,2.406 0.156,0.198 10 false A 0.948,1.177 1.771,1.427 0.823,0.25 10 false Target bar 1.896,3.188 5.469,3.469 3.573,0.281 10 false Making the left and right gaps of A and target bar equal 0.271,0.146 4.385,0.479 4.115,0.333 10 false When the adjustment position for A and target bar do not match: 5.51,1.135 6.333,1.385 0.823,0.25 10 false Target bar




ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.



g.
E280735E03
0.917,2.646 1.448,2.156 false 2.313,1.729 3.042,1.635 false 0.385,1.625 1.104,1.74 false 2.729,2.094 2.344,2.656 2.344,2.656 0.646,2.042 false 0.208,1.542 0.448,1.719 0.24,0.177 10 false A 3.094,1.552 3.333,1.729 0.24,0.177 10 false B 0.323,2.677 1.542,2.948 1.219,0.271 10 false Bumper Edge Line 0.125,0.094 2.302,0.51 2.177,0.417 10 false Adjustment for left and right bumper reference lines: 2.021,2.677 3.156,3.094 1.135,0.417 10 false Bumper Reference Line

BUMPER (SIMULTANEOUS ADJUSTMENT)

i.

By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.

HINT:
·

If the bumper reference lines do not overlap or contact the bumper edge line, select "L/R" to perform bumper reference line position adjustment (individual adjustment).

·

Adjust the position of the bumper reference lines so that they touch the left and right edges of the screen.




ii.

When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".



h.

LEFT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E212175E03
1.083,1.667 0.323,1.542 false 3.021,1.573 2.292,1.667 false 0.365,2.5 0.188,2.5 0.188,2.5 0.51,1.948 false 1.979,2.542 1.833,2.542 1.833,2.542 2.104,2.083 false 0.167,1.458 0.323,1.656 0.156,0.198 10 false A 3.094,1.49 3.25,1.688 0.156,0.198 10 false B 0.427,2.438 1.552,2.792 1.125,0.354 10 false Bumper Reference Line 2.031,2.458 3.198,2.74 1.167,0.281 10 false Bumper Edge Line 0.146,0.135 2.771,0.438 2.625,0.302 10 false Adjustment for left bumper reference line:

By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the left bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the left edge of the screen.




ii.

Select "NEXT" on the "LEFT BUMPER" screen.



i.

RIGHT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E238101E03
1.031,1.677 0.302,1.563 false 2.396,1.677 3.042,1.563 false 1.521,2.771 1.625,2.771 1.625,2.771 1.625,2.229 false 3.125,2.729 3.26,2.729 3.26,2.729 2.865,2.021 false 0.146,1.479 0.302,1.677 0.156,0.198 10 false A 3.094,1.479 3.25,1.677 0.156,0.198 10 false B 0.333,2.688 1.521,2.948 1.188,0.26 10 false Bumper Edge Line 1.938,2.635 3.094,3.042 1.156,0.406 10 false Bumper Reference Line 0.219,0.198 2.948,0.521 2.729,0.323 10 false Adjustment for right bumper reference line:

By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the right bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the right edge of the screen.




ii.

Select "NEXT" on the "RIGHT BUMPER" screen.



j.

BACK VERIFY MODE

i.
E213097E04
1.188,2.594 1.563,2.188 false 0.677,2.01 2.344,2.573 2.344,2.573 2.875,2.01 false 1.094,1.573 1.5,0.417 1.5,0.417 1.667,0.417 true 1.875,1.563 2.479,0.719 true 2.5,1.573 1.5,0.417 true 0.531,2.625 1.396,3.063 0.865,0.438 10 false Bumper Edge Line 1.854,2.625 3,2.99 1.146,0.365 10 false Bumper Reference Line 1.771,0.323 2.667,0.552 0.896,0.229 10 false Target bar 2.531,0.604 2.781,0.854 0.25,0.25 10 false A

Check that line A (indicating 1100 mm from the bumper edge) and the target bars are nearly overlapping and that the bumper reference lines and bumper edge line are nearly overlapping. With the steering wheel centered, check that the predicted path line is straight (overlapping the vehicle width extension lines).


ii.

Selecting "OK" on the "BACK VERIFY MODE" screen completes "BACK CAMERA POSITION SETTING".

HINT:
·

When "OK" is selected, a beep will sound to confirm that the "BACK CAMERA POSITION SETTING" values have been stored.

·

The values will not be stored unless "OK" is selected.

·

The values are not stored until the beep has sounded.






l.

Confirm steering angle adjustment.

HINT:

If the steering angle setting procedure has been performed, confirm the steering angle adjustment using the intelligent parking assist screen after finishing diagnosis mode.


i.

Check on the intelligent parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.





HEIGHT CONTROL SENSOR VEHICLE HEIGHT DIFFERENCE SETTING (HEIGHT SET) (PROCEDURE 2)


a.

Preparation for adjustment

HINT:
·

HEIGHT SET (entering the height compensation value) must be performed on a level surface.

·

Before performing television camera optical axis adjustment, the height control sensor vehicle height difference setting must be performed in the "HEIGHT SET" screen.



i.

Adjust the tire pressure to the specified value.


ii.
E187169E02
0.11,0.065 1.270,0.244 1.161,0.179 10 Rear Wheel Side: 2.706,1.976 2.862,2.150 0.156,0.174 10 A 2.293,0.23 3.198,0.568 0.905,0.339 10 Measurement Position 1.044,1.553 1.822,0.313 1.822,0.313 2.253,0.313 false 1.038,2.097 1.382,2.927 1.382,2.927 1.588,2.927 false 1.614,2.842 2.464,3.005 0.850,0.163 10 Center of tire

Measure distance A between the ground and the edge of a rear wheel arch.


iii.

Calculate the difference between distance A and the standard height below.

Standard height:

701 mm (2.30 ft.)


HINT:

Subtract the standard height from the measured value to get the height compensation value. When the measured value is 711 mm: 711 - 701= +10 (height compensation value is +10 mm).




b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting I" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E311252

Select "BACK CAMERA SETTING" on the "MODE SETTING" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
U191439E02
3.135,0.688 3.323,0.865 0.188,0.177 10 false A

Select indicator A for "HT INIT" on the "SIGNAL CHECK" screen.

NOTICE:

When "CHK" (red) is displayed for any items except "HT INIT" on the "SIGNAL CHECK" screen, perform inspections using the "SIGNAL CHECK" screen.


HINT:

When the screen does not change to the "HEIGHT SET" screen, check for DTCs and perform troubleshooting based on the output DTCs.




c.

HEIGHT SET

i.
E311251

Press "UP" or "DOWN" to enter the height compensation value calculated previously.

HINT:
·

Positive values are indicated in green and negative values are indicated in red.

·

When the value is shown as "10 MM" in green, it means +10 mm.

·

Available setting range: -102 mm to +102 mm (can be adjusted in 1 mm increments)




ii.

After entering the height compensation value, select "OK". The setting will be stored.

HINT:
·

When "OK" is selected, a beep will sound to confirm that the height compensation value has been stored.

·

The value will not be stored unless "OK" is selected.

·

The value is not stored until the beep has sounded.

·

When "BACK" is selected, the screen changes to "SIGNAL CHECK" screen without storing the value.

·

Press "OK" with the vehicle in the same condition as when the vehicle height was measured.

·

If a person was in the driver seat when the vehicle height was measured, press "OK" with the same person in the driver seat.

·

On the "SIGNAL CHECK" screen, check that indicator A for "HT INIT" is "OK" (blue).







REAR TELEVISION CAMERA OPTICAL AXIS ADJUSTMENT (CAMERA POSITION SETTING) (PROCEDURE 3)


HINT:

Be sure to check for DTCs before performing this procedure.


a.

Preparation for adjustment

NOTICE:

Before performing television camera optical axis adjustment, the height compensation value must be entered using the "HEIGHT SET" screen (Height Control Sensor Vehicle Height Difference Setting).


i.

Park the vehicle with the steering wheel centered.

HINT:

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.



ii.

Adjust the tire pressure to the specified value.


iii.

Set a target bar behind the vehicle for optical axis adjustment of the rear television camera.

HINT:

Only when adjusting the optical axis of the camera, create a target bar for adjustment.


E267675E05
4.281,1.698 4.833,1.167 false 2.417,1.698 1.969,1.167 false 3.771,0.333 4.417,0.5 0.646,0.167 10 false *2 4.885,1.083 6.219,1.25 1.333,0.167 10 false *1 1.76,1.063 3.094,1.229 1.333,0.167 10 false *1 3.802,0.75 3.948,0.917 0.146,0.167 10 false B 2.833,0.75 2.979,0.917 0.146,0.167 10 false B 3.938,1.083 4.083,1.25 0.146,0.167 10 false C 2.688,1.083 2.833,1.25 0.146,0.167 10 false C 1.667,1.677 1.813,1.844 0.146,0.167 10 false D 4.958,1.656 5.104,1.823 0.146,0.167 10 false D 3,1.729 3.146,1.896 0.146,0.167 10 false F 3.656,1.729 3.802,1.896 0.146,0.167 10 false F 2.573,2.24 2.719,2.406 0.146,0.167 10 false E 4.083,2.24 4.229,2.406 0.146,0.167 10 false E 6.25,2.375 6.396,2.542 0.146,0.167 10 false A 3.115,3.708 4.021,4.031 0.906,0.323 10 false Vehicle 4.167,3.667 4.75,3.833 0.583,0.167 10 false *3 4,4.125 4.583,4.292 0.583,0.167 10 false *4

Dimension:
A B C D E F
1100 mm
(3.61 ft.)
1600 mm
(5.25 ft.)
30 mm
(1.18 in.)
100 mm
(3.94 in.)
500 mm
(1.64 ft.)
30 mm
(1.18 in.)


Text in Illustration
*1 Target Bar for Camera Adjustment *2 Vehicle Center
*3 Bumper Edge *4 Front Side

HINT:

Check the tape color on the radio and display receiver assembly*1 or navigation receiver assembly*2 and choose a tape color which can be easily seen.


*1: for Radio and Display Type

*2: for Navigation Receiver Type




b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting I" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E311252

Select "BACK CAMERA SETTING" on the "MODE SETTING" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E305121

Select "NEXT" on the "SIGNAL CHECK" screen.

NOTICE:

When "CHK" (red) is displayed for any items except "HT INIT" on the "SIGNAL CHECK" screen, perform inspections using the "SIGNAL CHECK" screen.




c.
E214489E05
1.021,1.635 1.667,0.75 1.667,0.75 1.917,0.75 true 2.115,2.625 1.927,2.354 true 1.427,2.635 1.583,2.354 true 0.896,1.563 0.469,1.344 true 2.5,1.667 1.667,0.75 true 2,0.677 3.031,0.99 1.031,0.313 10 false Target bar 1.354,2.677 1.51,2.875 0.156,0.198 10 false A 2.115,2.677 2.271,2.875 0.156,0.198 10 false B 0.313,1.219 0.469,1.417 0.156,0.198 10 false C

"BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT)

NOTICE:

Before performing television camera optical axis adjustment, the height compensation value must be entered using the "HEIGHT SET" screen (Height Control Sensor Vehicle Height Difference Setting).


HINT:
·

When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and television camera optical axis adjustment will not be possible.

·

If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after the back door is closed) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE).



i.

Select switches A and B to rotate C so that it is parallel to the target adjustment bar.


ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT) screen.



d.

"BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)

i.
E236781E05
0.969,1.552 1.615,0.677 1.615,0.677 2.417,1.542 true 0.833,1.635 1.74,2.625 1.74,2.625 2.552,1.625 true 1.427,2.688 2.25,3 0.823,0.313 10 false Target bar 1.531,0.448 1.781,0.635 0.25,0.188 10 false A

By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars (C) and the corners of the parallelograms (A) match.

E212177E05
5.344,1.583 6,0.583 6,0.583 5.75,0.583 true 5.99,1.802 6.125,1.979 false 4.688,1.427 4.49,1.688 false 0.271,0.188 3.146,0.479 2.875,0.292 10 false Adjustment position for A and target bar: 5,0.49 5.771,0.75 0.771,0.26 10 false Target bar 6.135,1.969 6.375,2.208 0.24,0.24 10 false C 4.396,1.688 4.708,2 0.313,0.313 10 false A 4.76,2.167 6.219,2.448 1.458,0.281 10 false Matching corner C

NOTICE:
·

If the left and right parallelograms (A) and target bars do not match completely, just match the corners of the target bars (C) with the corners of the parallelograms (A).

·

If the left and right parallelograms (A) and the corners of the target bars (C) do not match, make the gaps between each parallelogram (A) and the target bars equal on the left and right sides.

E212178E03
1.125,1.99 0.667,1.26 0.667,1.26 0.885,1.26 true 5.469,1.885 5.313,2.146 false 6.5,2.219 3.479,3.125 3.479,3.125 0.625,2.26 false 1.906,2.146 1.667,1.917 false 6.052,1.99 6.479,1.24 6.479,1.24 6.229,1.24 true 1.938,2.146 2.094,2.344 0.156,0.198 10 false A 5.24,2.208 5.396,2.406 0.156,0.198 10 false A 0.948,1.177 1.771,1.427 0.823,0.25 10 false Target bar 1.896,3.188 5.469,3.469 3.573,0.281 10 false Making the left and right gaps of A and target bar equal 0.271,0.146 4.385,0.479 4.115,0.333 10 false When the adjustment position for A and target bar do not match: 5.51,1.135 6.333,1.385 0.823,0.25 10 false Target bar




ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.



e.
E280735E03
0.917,2.646 1.448,2.156 false 2.313,1.729 3.042,1.635 false 0.385,1.625 1.104,1.74 false 2.729,2.094 2.344,2.656 2.344,2.656 0.646,2.042 false 0.208,1.542 0.448,1.719 0.24,0.177 10 false A 3.094,1.552 3.333,1.729 0.24,0.177 10 false B 0.323,2.677 1.542,2.948 1.219,0.271 10 false Bumper Edge Line 0.125,0.094 2.302,0.51 2.177,0.417 10 false Adjustment for left and right bumper reference lines: 2.021,2.677 3.156,3.094 1.135,0.417 10 false Bumper Reference Line

BUMPER (SIMULTANEOUS ADJUSTMENT)

i.

By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.

HINT:
·

If the bumper reference lines do not overlap or contact the bumper edge line, select "L/R" to perform bumper reference line position adjustment (individual adjustment).

·

Adjust the positions of the bumper reference lines so that they touch the left and right edges of the screen.




ii.

When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".



f.

LEFT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E212175E03
1.083,1.667 0.323,1.542 false 3.021,1.573 2.292,1.667 false 0.365,2.5 0.188,2.5 0.188,2.5 0.51,1.948 false 1.979,2.542 1.833,2.542 1.833,2.542 2.104,2.083 false 0.167,1.458 0.323,1.656 0.156,0.198 10 false A 3.094,1.49 3.25,1.688 0.156,0.198 10 false B 0.427,2.438 1.552,2.792 1.125,0.354 10 false Bumper Reference Line 2.031,2.458 3.198,2.74 1.167,0.281 10 false Bumper Edge Line 0.146,0.135 2.771,0.438 2.625,0.302 10 false Adjustment for left bumper reference line:

By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the left bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the left edge of the screen.




ii.

Select "NEXT" on the "LEFT BUMPER" screen.



g.

RIGHT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E238101E03
1.031,1.677 0.302,1.563 false 2.396,1.677 3.042,1.563 false 1.521,2.771 1.625,2.771 1.625,2.771 1.625,2.229 false 3.125,2.729 3.26,2.729 3.26,2.729 2.865,2.021 false 0.146,1.479 0.302,1.677 0.156,0.198 10 false A 3.094,1.479 3.25,1.677 0.156,0.198 10 false B 0.333,2.688 1.521,2.948 1.188,0.26 10 false Bumper Edge Line 1.938,2.635 3.094,3.042 1.156,0.406 10 false Bumper Reference Line 0.219,0.198 2.948,0.521 2.729,0.323 10 false Adjustment for right bumper reference line:

By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the right bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the right edge of the screen.




ii.

Select "NEXT" on the "RIGHT BUMPER" screen.



h.

BACK VERIFY MODE

i.
E213097E04
1.188,2.594 1.563,2.188 false 0.677,2.01 2.344,2.573 2.344,2.573 2.875,2.01 false 1.094,1.573 1.5,0.417 1.5,0.417 1.667,0.417 true 1.875,1.563 2.479,0.719 true 2.5,1.573 1.5,0.417 true 0.531,2.625 1.396,3.063 0.865,0.438 10 false Bumper Edge Line 1.854,2.625 3,2.99 1.146,0.365 10 false Bumper Reference Line 1.771,0.323 2.667,0.552 0.896,0.229 10 false Target bar 2.531,0.604 2.781,0.854 0.25,0.25 10 false A

Check that line A (indicating 1100 mm from the bumper edge) and the target bars are nearly overlapping and that the bumper reference lines and bumper edge line are nearly overlapping. With the steering wheel centered, check that the predicted path line is straight (overlapping the vehicle width extension lines).


ii.

Selecting "OK" on the "BACK VERIFY MODE" screen completes the back camera position setting.

HINT:
·

When "OK" is selected, a beep will sound to confirm that the back camera position setting values have been stored.

·

The values will not be stored unless "OK" is selected.

·

The values are not stored until the beep has sounded.







BUMPER POSITION SETTING (PROCEDURE 4)


a.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting I" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E311252

Select "BACK CAMERA SETTING" on the "MODE SETTING" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E305121

Select "NEXT" on the "SIGNAL CHECK" screen.

NOTICE:

When "CHK" (red) is displayed for any items except "HT INIT" on the "SIGNAL CHECK" screen, perform inspections using the "SIGNAL CHECK" screen.




b.
E214489E05
1.021,1.635 1.667,0.75 1.667,0.75 1.917,0.75 true 2.115,2.625 1.927,2.354 true 1.427,2.635 1.583,2.354 true 0.896,1.563 0.469,1.344 true 2.5,1.667 1.667,0.75 true 2,0.677 3.031,0.99 1.031,0.313 10 false Target bar 1.354,2.677 1.51,2.875 0.156,0.198 10 false A 2.115,2.677 2.271,2.875 0.156,0.198 10 false B 0.313,1.219 0.469,1.417 0.156,0.198 10 false C

"BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT)

HINT:
·

When only bumper reference line position adjustment is required after servicing the vehicle, "BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT) is unnecessary. Select "NEXT".

·

When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and television camera optical axis adjustment will not be possible.

·

If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after the back door is closed).



i.

Select switches A and B to rotate C so that it is parallel to the target adjustment bar.


ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (ROLL ANGLE ADJUSTMENT) screen.



c.
E236781E05
0.969,1.552 1.615,0.677 1.615,0.677 2.417,1.542 true 0.833,1.635 1.74,2.625 1.74,2.625 2.552,1.625 true 1.427,2.688 2.25,3 0.823,0.313 10 false Target bar 1.531,0.448 1.781,0.635 0.25,0.188 10 false A

"BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)

HINT:

When only bumper reference line position adjustment is required after servicing the vehicle, "BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) is unnecessary. Select "NEXT".


i.

By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars and the corners of the parallelograms (A) match.


ii.

Select "NEXT" on the "BACK CAMERA POSITION SETTING" (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.



d.
E280735E03
0.917,2.646 1.448,2.156 false 2.313,1.729 3.042,1.635 false 0.385,1.625 1.104,1.74 false 2.729,2.094 2.344,2.656 2.344,2.656 0.646,2.042 false 0.208,1.542 0.448,1.719 0.24,0.177 10 false A 3.094,1.552 3.333,1.729 0.24,0.177 10 false B 0.323,2.677 1.542,2.948 1.219,0.271 10 false Bumper Edge Line 0.125,0.094 2.302,0.51 2.177,0.417 10 false Adjustment for left and right bumper reference lines: 2.021,2.677 3.156,3.094 1.135,0.417 10 false Bumper Reference Line

BUMPER (SIMULTANEOUS ADJUSTMENT)

i.

By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.

HINT:
·

If the bumper reference lines do not overlap or contact the bumper edge line, select "L/R" to perform bumper reference line position adjustment (individual adjustment).

·

Adjust the bumper reference line position so that they touch the left and right edges of the screen.




ii.

When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".



e.

LEFT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E212175E03
1.083,1.667 0.323,1.542 false 3.021,1.573 2.292,1.667 false 0.365,2.5 0.188,2.5 0.188,2.5 0.51,1.948 false 1.979,2.542 1.833,2.542 1.833,2.542 2.104,2.083 false 0.167,1.458 0.323,1.656 0.156,0.198 10 false A 3.094,1.49 3.25,1.688 0.156,0.198 10 false B 0.427,2.438 1.552,2.792 1.125,0.354 10 false Bumper Reference Line 2.031,2.458 3.198,2.74 1.167,0.281 10 false Bumper Edge Line 0.146,0.135 2.771,0.438 2.625,0.302 10 false Adjustment for left bumper reference line:

By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the left bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the left edge of the screen.




ii.

Select "NEXT" on the "LEFT BUMPER" screen.



f.

RIGHT BUMPER (INDIVIDUAL ADJUSTMENT)

i.
E238101E03
1.031,1.677 0.302,1.563 false 2.396,1.677 3.042,1.563 false 1.521,2.771 1.625,2.771 1.625,2.771 1.625,2.229 false 3.125,2.729 3.26,2.729 3.26,2.729 2.865,2.021 false 0.146,1.479 0.302,1.677 0.156,0.198 10 false A 3.094,1.479 3.25,1.677 0.156,0.198 10 false B 0.333,2.688 1.521,2.948 1.188,0.26 10 false Bumper Edge Line 1.938,2.635 3.094,3.042 1.156,0.406 10 false Bumper Reference Line 0.219,0.198 2.948,0.521 2.729,0.323 10 false Adjustment for right bumper reference line:

By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference line overlaps or contacts the bumper edge line.

HINT:
·

When the right bumper reference line overlaps or contacts the bumper edge line in the bumper reference line position adjustment (individual adjustment) step, select "NEXT".

·

Adjust the position of the bumper reference line so that it touches the right edge of the screen.




ii.

Select "NEXT" on the "RIGHT BUMPER" screen.



g.

BACK VERIFY MODE

i.
E213097E04
1.188,2.594 1.563,2.188 false 0.677,2.01 2.344,2.573 2.344,2.573 2.875,2.01 false 1.094,1.573 1.5,0.417 1.5,0.417 1.667,0.417 true 1.875,1.563 2.479,0.719 true 2.5,1.573 1.5,0.417 true 0.531,2.625 1.396,3.063 0.865,0.438 10 false Bumper Edge Line 1.854,2.625 3,2.99 1.146,0.365 10 false Bumper Reference Line 1.771,0.323 2.667,0.552 0.896,0.229 10 false Target bar 2.531,0.604 2.781,0.854 0.25,0.25 10 false A

Check that the bumper reference lines and bumper edge line are nearly overlapping.


ii.

Selecting "OK" on the "BACK VERIFY MODE" screen completes Bumper Position Setting.

HINT:
·

When "OK" is selected, a beep will sound to confirm that the Bumper Position Setting values have been stored.

·

The values will not be stored unless "OK" is selected.

·

The values are not stored until the beep has sounded.