Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2016.05–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1627  Vehicle Height Sensor Voltage is Low or High  


DESCRIPTION

The rear height control sensor sub-assembly RH and headlight leveling ECU assembly (for LED headlight) are connected to the parking assist ECU. The parking assist ECU shares the vehicle height signals received from the rear height control sensor sub-assembly RH with the lighting system (auto leveling). The headlight leveling ECU assembly (for LED headlight) supplies power to the rear height control sensor sub-assembly RH via the parking assist ECU. This DTC is stored when the parking assist ECU judges that the power supply voltage for the rear height control sensor sub-assembly RH is not normal.

DTC No. DTC Detection Condition Trouble Area
C1627
·

Height control sensor voltage is low

·

Height control sensor voltage is high


·

Harness or connector

·

Headlight leveling ECU assembly (for LED Headlight)

·

Parking assist ECU



WIRING DIAGRAM

for LED Headlight


E232911E05
0.323,1.896 0.74,2.073 0.417,0.177 10 false S25 0.323,2.052 2.021,2.458 1.698,0.406 10 false Rear Height Control Sensor Sub-assembly RH 2.948,1.938 3.25,2.094 0.302,0.156 10 false L65 2.938,2.083 4.292,2.333 1.354,0.25 10 false Parking Assist ECU 5.177,1.938 5.479,2.094 0.302,0.156 10 false A48 5.021,0.469 5.208,0.625 0.188,0.156 10 false 12 5.042,1.333 5.229,1.49 0.188,0.156 10 false 21 4.26,0.458 4.448,0.615 0.188,0.156 10 false 28 4.26,1.323 4.448,1.479 0.188,0.156 10 false 29 2.729,0.469 2.917,0.625 0.188,0.156 10 false 27 2.729,1.323 2.917,1.479 0.188,0.156 10 false 31 1.938,0.469 2.125,0.625 0.188,0.156 10 false 3 1.938,1.344 2.125,1.5 0.188,0.156 10 false 1 5.302,0.573 5.865,0.979 0.563,0.406 10 false SBR 5.302,1.438 5.646,1.594 0.344,0.156 10 false SGR 1.563,0.563 2.021,0.833 0.458,0.271 10 false SHB 1.563,1.438 1.906,1.594 0.344,0.156 10 false SHG 3.865,0.573 4.167,0.729 0.302,0.156 10 false HB+ 3.75,1.438 4.208,1.594 0.458,0.156 10 false HGND 2.99,0.573 3.448,0.729 0.458,0.156 10 false HBL+ 2.99,1.448 3.344,1.604 0.354,0.156 10 false HG1 5.167,2.094 6.698,2.458 1.531,0.365 10 false Headlight Leveling ECU Assembly


for Halogen Headlight


E232912E04
1.128,1.811 1.414,1.962 0.287,0.151 10 S25 2.675,0.328 2.810,0.479 0.135,0.151 10 3 2.675,1.196 2.810,1.347 0.135,0.151 10 1 4.365,1.196 4.566,1.347 0.201,0.151 10 31 2.287,0.425 2.603,0.576 0.316,0.151 10 SHB 2.287,1.294 2.610,1.445 0.323,0.151 10 SHG 4.609,1.294 4.931,1.445 0.323,0.151 10 HG1 1.128,1.962 2.860,2.289 1.732,0.327 10 Rear Height Control Sensor Sub-assembly RH 4.585,1.811 4.936,1.962 0.350,0.151 10 L65 4.585,1.962 5.852,2.122 1.267,0.161 10 Parking Assist ECU 4.365,0.328 4.559,0.479 0.194,0.151 10 30 4.609,0.425 5.091,0.576 0.482,0.151 10 HBE+


CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the radio and display receiver assembly*1 or navigation receiver assembly*2 after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).

·

When the headlight leveling ECU assembly (for LED headlight) is replaced, perform initialization for the lighting system (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION)

·

If initialization is necessary while performing an inspection, perform initialization first and then proceed to the next step.


*1: for Radio and Display Type

*2: for Navigation Receiver Type



PROCEDURE

1.CHECK DTC OUTPUT

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1627 is output A
DTCs are not output B



HINT:
·

If the power source voltage output by the headlight leveling ECU assembly (for LED headlight) is abnormal, the headlight leveling warning light may come on.

·

If the DTCs are not output again when rechecking for DTCs, it may have been stored due to a temporarily abnormal voltage.

·

If DTC C1627 is output frequently, duplicate the problem symptoms and perform the inspection again, even if the DTC is not output when rechecking for DTCs (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).




A

2.CHECK VEHICLE SPECIFICATION

B

2.CHECK VEHICLE SPECIFICATION
a.

Check vehicle specifications.

Result:
Result Proceed to
for LED Headlight A
for Halogen Headlight B




A

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - PARKING ASSIST ECU)

B

6.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the A48 headlight leveling ECU assembly connector.


b.

Disconnect the L65 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-12 (SBR) - Body ground Always 10 kΩ or higher
A48-21 (SGR) - Body ground Always 10 kΩ or higher
A48-12 (SBR) - L65-28 (HB+) Always Below 1 Ω
A48-21 (SGR) - L65-29 (HGND) Always Below 1 Ω




OK

4.CHECK HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HEADLIGHT LEVELING ECU ASSEMBLY
a.

Reconnect the A48 headlight leveling ECU assembly connector.


b.

Disconnect the L65 parking assist ECU connector.


c.
U191300E01
2.193,1.861 2.648,2.008 0.455,0.147 10 HGND 2.166,0.214 2.494,0.395 0.328,0.181 10 L65 0.123,0.097 0.288,0.244 0.165,0.147 10 *a 1.596,1.468 1.596,1.943 1.596,1.943 1.123,1.943 false 1.691,1.468 1.691,1.943 1.691,1.943 2.163,1.943 false 0.745,1.861 1.202,2.008 0.457,0.147 10 HB+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L65-28 (HB+) - L65-29 (HGND) Power switch on (IG) 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)



OK

5.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)

NG

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the S25 rear height control sensor sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-27 (HBL+) - Body ground Always 10 kΩ or higher
L65-31 (HG1) - Body ground Always 10 kΩ or higher
L65-27 (HBL+) - S25-3 (SHB) Always Below 1 Ω
L65-31 (HG1) - S25-1 (SHG) Always Below 1 Ω


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
6.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the S25 rear height control sensor sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-30 (HBE+) - Body ground Always 10 kΩ or higher
L65-31 (HG1) - Body ground Always 10 kΩ or higher
L65-30 (HBE+) - S25-3 (SHB) Always Below 1 Ω
L65-31 (HG1) - S25-1 (SHG) Always Below 1 Ω




OK

7.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
a.

Reconnect the L65 parking assist ECU connector.


b.

Disconnect the S25 rear height control sensor sub-assembly RH connector.


c.
U191342E02
1.896,1.51 2.542,1.51 false 0.906,1.51 1.552,1.51 false 1.604,0.24 1.875,0.417 0.271,0.177 10 false S25 2.583,1.438 3.177,1.625 0.594,0.188 10 false SHB 0.573,1.427 1.167,1.615 0.594,0.188 10 false SHG 0.135,0.063 0.729,0.25 0.594,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S25-3 (SHB) - S25-1 (SHG) Power switch on (IG) 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Height Control Sensor Sub-assembly RH)



OK

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

NG