Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B1273 No communication between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Roof sunshade ECU (sliding roof drive gear assembly)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

S/ROOF fuse



WIRING DIAGRAM

B315277E02
4.25,1.783 6.415,2.110 2.165,0.327 10 Roof Sunshade ECU (Sliding Roof Drive Gear assembly) 4.25,1.639 5.127,1.785 0.877,0.147 10 z21 4.618,0.597 4.855,0.733 0.237,0.136 10 4 2.172,0.597 2.347,0.733 0.176,0.136 10 16 3.131,0.597 3.307,0.733 0.176,0.136 10 27 5.721,0.536 5.904,0.673 0.183,0.136 10 1 5.721,1.376 5.919,1.512 0.198,0.136 10 2 4.773,0.466 5.220,0.613 0.448,0.147 10 MPX1 1.789,0.466 2.102,0.613 0.313,0.147 10 LIN2 0.624,0.857 0.869,1.010 0.245,0.153 10 MB 0.624,1.016 2.273,1.346 1.649,0.329 10 Main Body ECU (Multiplex Network Body ECU) 0.569,1.671 0.769,1.824 0.200,0.153 10 2A 0.559,1.804 3.231,1.957 2.672,0.153 10 Instrument Panel Junction Block Assembly 0.445,2.482 2.066,2.635 1.621,0.153 10 : LIN Communication Line 5.564,0.466 5.680,0.613 0.115,0.147 10 B 5.564,1.289 5.708,1.436 0.144,0.147 10 E 6.129,0.552 6.729,0.694 0.601,0.142 10 S/ROOF

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190812E02
2.042,1.698 2.667,2.219 true 5.385,1.708 6.063,2.229 true 0.24,0.156 0.448,0.323 0.208,0.167 10 false *1 4.854,0.156 5.063,0.323 0.208,0.167 10 false *2 1.917,1.167 2.156,1.313 0.24,0.146 10 false MB 5.594,0.906 5.792,1.052 0.198,0.146 10 false 2A 5.938,2.24 6.302,2.417 0.365,0.177 10 false LIN2 2.542,2.219 2.906,2.396 0.365,0.177 10 false LIN2


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2)- MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument Panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ROOF SUNSHADE ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ROOF SUNSHADE ECU)
a.

Disconnect the z21 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - z21-4 (MPX1) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - AUXILIARY BATTERY, BODY GROUND)
a.
U190794E02
1.156,1.302 1.125,1.833 false 1.458,1.302 1.552,1.833 false 0.469,1.24 0.771,1.448 0.302,0.208 10 false z21 0.125,0.094 0.271,0.229 0.146,0.135 10 false *1 1.073,1.854 1.229,2.094 0.156,0.24 10 false B 1.521,1.854 1.646,2.042 0.125,0.188 10 false E

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z21-1 (B) - z21-2 (E) Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z21-2 (E) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Front view of wire harness connector
(to Roof Sunshade ECU (Sliding Roof Drive Gear assembly))



OK

4.REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Replace the roof sunshade ECU (sliding roof drive gear assembly) (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B1273 is not output.




OK

END (ROOF SUNSHADE ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)