Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) stores a DTC when communication with the double lock door control relay assembly is interrupted for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B1249 Communication between double lock door control relay assembly and main body ECU (multiplex network body ECU) interrupted for 10 seconds or more, or communication wire malfunction.
·

Double lock door control relay assembly

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DBL LOCK fuse

·

ECU-B fuse



WIRING DIAGRAM

B220699E24
4.375,1.854 6.01,2.167 1.635,0.313 10 false Double Lock Door Control Relay Assembly 0.542,1.802 3.219,1.948 2.677,0.146 10 false Instrument Panel Junction Block Assembly 0.448,2.49 2.073,2.635 1.625,0.146 10 false : LIN Communication Line 0.625,0.865 0.865,1.021 0.24,0.156 10 false MB 0.625,1.021 2.281,1.333 1.656,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 1.792,0.469 2.104,0.615 0.313,0.146 10 false LIN2 0.563,1.667 0.771,1.813 0.208,0.146 10 false 2A 3.125,0.323 3.302,0.469 0.177,0.146 10 false 27 4.375,1.688 4.729,1.833 0.354,0.146 10 false L145 2.146,0.604 2.323,0.75 0.177,0.146 10 false 16 4.781,0.469 5.208,0.615 0.427,0.146 10 false MPX1 5.469,0.448 5.677,0.594 0.208,0.146 10 false +B 5.26,0.917 5.677,1.063 0.417,0.146 10 false CPUB 6.083,0.563 6.813,0.708 0.729,0.146 10 false DBL LOCK 6.115,1.021 6.573,1.167 0.458,0.146 10 false ECU-B 5.333,1.292 5.677,1.438 0.344,0.146 10 false GND 5.719,0.365 5.823,0.51 0.104,0.146 10 false 1 5.719,0.833 5.823,0.979 0.104,0.146 10 false 7 5.719,1.208 5.906,1.354 0.188,0.146 10 false 14 4.594,0.333 4.719,0.479 0.125,0.146 10 false 9

CAUTION / NOTICE / HINT

HINT:

When the main body ECU (multiplex network body ECU) has been replaced with a new part, and the cable from negative (-) auxiliary battery terminal is reconnected, the power switch will be on (IG). Also, when the auxiliary battery has been removed and installed, the condition will be the same as it was before the auxiliary battery was disconnected.


NOTICE:
·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190812E02
2.042,1.698 2.667,2.219 true 5.385,1.708 6.063,2.229 true 0.24,0.156 0.448,0.323 0.208,0.167 10 false *1 4.854,0.156 5.063,0.323 0.208,0.167 10 false *2 1.917,1.167 2.156,1.313 0.24,0.146 10 false MB 5.594,0.906 5.792,1.052 0.198,0.146 10 false 2A 5.938,2.24 6.302,2.417 0.365,0.177 10 false LIN2 2.542,2.219 2.906,2.396 0.365,0.177 10 false LIN2


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument Panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the L145 double lock door control relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - L145-9 (MPX1) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - AUXILIARY BATTERY, BODY GROUND)
a.
U191236E02
0.958,1.24 0.604,1.5 false 1.042,1.521 0.896,1.844 false 2.396,1.531 2.531,1.813 false 0.313,0.167 0.552,0.354 0.24,0.188 10 false *1 0.26,1.052 0.646,1.281 0.385,0.229 10 false L145 0.396,1.479 0.656,1.667 0.26,0.188 10 false +B 0.698,1.854 1.156,2.042 0.458,0.188 10 false CPUB 2.417,1.823 2.875,2.01 0.458,0.188 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L145-1 (+B) - Body ground Power switch off 11 to 14 V
L145-7 (CPUB) - Body ground Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L145-14 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)



OK

4.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Replace the double lock door control relay assembly.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B1249 is not output.




OK

END (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)