Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2012.03–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2287  LIN Communication Master Malfunction  


DESCRIPTION

This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly).

DTC No. DTC Detection Condition Trouble Area
B2287 There is an open, short or ECU communication malfunction between power management control ECU and certification ECU (smart key ECU assembly).
·

Power management control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B203745E19
1.135,2.445 2.754,2.592 1.619,0.147 10 : LIN Communication Line 0.885,1.771 2.964,1.918 2.079,0.147 10 Power Management Control ECU 0.885,1.618 1.152,1.774 0.267,0.156 10 L6 4.436,1.618 4.717,1.770 0.281,0.151 10 L62 4.436,1.771 6.017,2.084 1.582,0.313 10 Certification ECU (Smart Key ECU Assembly) 2.427,1.044 2.750,1.195 0.323,0.151 10 LIN2 4.436,1.044 4.693,1.191 0.258,0.147 10 LIN 2.806,0.913 2.983,1.051 0.177,0.137 10 11 4.202,0.913 4.404,1.092 0.202,0.179 10 29

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly) is replaced, register the key.

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

HINT:

Check the both "Entry&Start" and "Power Source Control" DTCs.


Result:
Result Proceed to
Only DTC B2287 is output. A
DTC B2287 and B2785 are output simultaneously. B


HINT:

When DTC B2287 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the L6 power management control ECU and L62 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-11 (LIN2) - L62-29 (LIN) Always Below 1 Ω
L6-11 (LIN2) - Body ground Always 10 kΩ or higher




OK

3.REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2287 is not output.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)