Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2013.08–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Power window regulator motor assembly (for driver side)

·

Power window regulator motor assembly (for front passenger side)

·

Power window regulator motor assembly (for rear RH side)

·

Power window regulator motor assembly (for rear LH side)

·

Multiplex network master switch assembly

·

Roof sunshade ECU (sliding roof drive gear assembly)*1

·

Double lock door control relay assembly*2

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector



*1: w/ Roof Sunshade System

*2: w/ Double Locking System


WIRING DIAGRAM

B228557E13
0.733,8.473 2.382,8.622 1.649,0.149 10 : LIN Communication Line 1.019,6.219 3.008,6.535 1.989,0.316 10 Power Window Regulator Motor Assembly (for Driver Side) 0.711,4.678 3.394,4.848 2.684,0.170 10 Multiplex Network Master Switch Assembly 0.599,7.723 3.421,7.893 2.823,0.170 10 Double Lock Door Control Relay Assembly*4 1.019,6.047 1.863,6.184 0.844,0.137 10 O2*1, N2*2 0.711,4.527 1.538,4.664 0.828,0.137 10 O6*1, N13*2 4.767,2.57 6.937,2.885 2.170,0.316 10 Roof Sunshade ECU (Sliding Roof Drive Gear Assembly)*3 4.683,4.426 6.978,4.742 2.295,0.316 10 Power Window Regulator Motor Assembly (for Front Passenger Side) 4.823,6.009 6.833,6.325 2.010,0.316 10 Power Window Regulator Motor Assembly (for Rear RH Side) 4.795,1 6.798,1.316 2.003,0.316 10 Power Window Regulator Motor Assembly (for Rear LH Side) 4.767,2.432 5.064,2.569 0.298,0.137 10 z21 4.55,1 4.838,1.138 0.288,0.137 10 Q4 4.683,4.274 5.462,4.411 0.779,0.137 10 N2*1, O2*2 4.823,5.85 5.019,5.988 0.196,0.137 10 P4 4.86,6.999 5.577,7.137 0.717,0.137 10 *1: for LHD 4.86,7.749 6.730,7.886 1.869,0.137 10 *3: w/ Roof Sunshade System 4.86,7.373 5.600,7.510 0.740,0.137 10 *2: for RHD 4.86,8.101 6.794,8.239 1.934,0.137 10 *4: w/ Double Locking System 3.177,0.508 3.372,0.645 0.196,0.137 10 2D 3.177,1.956 3.372,2.093 0.196,0.137 10 2A 0.594,2.63 3.248,2.767 2.654,0.137 10 Instrument Panel Junction Block Assembly 0.487,1.523 2.142,1.834 1.656,0.311 10 Main Body ECU (Multiplex Network Body ECU) 0.487,1.381 0.724,1.518 0.237,0.137 10 MB 1.696,0.508 2.021,0.645 0.325,0.137 10 LIN2 2.074,0.382 2.278,0.519 0.203,0.137 10 16 3.475,0.377 3.679,0.514 0.203,0.137 10 26 3.475,1.806 3.679,1.943 0.203,0.137 10 27 4.844,0.503 5.100,0.641 0.256,0.137 10 LIN 4.844,3.796 5.100,3.933 0.256,0.137 10 LIN 4.844,5.346 5.100,5.483 0.256,0.137 10 LIN 1.042,5.556 1.298,5.694 0.256,0.137 10 LIN 1.042,3.651 1.381,3.788 0.339,0.137 10 LIN2 2.672,3.651 3.011,3.788 0.339,0.137 10 LIN1 4.844,1.946 5.252,2.084 0.409,0.137 10 MPX1 0.884,5.439 1.001,5.577 0.117,0.137 10 9 0.81,3.66 1.001,3.797 0.191,0.137 10 16 3.051,3.66 3.243,3.797 0.191,0.137 10 17 4.681,3.66 4.789,3.797 0.108,0.137 10 9 4.681,0.396 4.789,0.533 0.108,0.137 10 9 4.681,1.829 4.789,1.967 0.108,0.137 10 4 4.681,5.229 4.789,5.366 0.108,0.137 10 9 0.599,7.555 0.987,7.692 0.388,0.137 10 L145 2.607,7.205 3.022,7.342 0.416,0.137 10 MPX1 3.056,7.074 3.173,7.211 0.117,0.137 10 9

CAUTION / NOTICE / HINT

NOTICE:
·

When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) - MASTER SWITCH)
a.

Disconnect the O6*1 or N13*2 multiplex network master switch connector.


b.

Disconnect the O2*1 or N2*2 power window regulator motor (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O6-16 (LIN2) - O2-9 (LIN)*1
N13-16 (LIN2) - N2-9 (LIN)*2
Always Below 1 Ω
O6-16 (LIN2) - Body ground*1
N13-16 (LIN2) - Body ground*2
Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B203350E04
0.614,1.567 0.814,1.764 0.200,0.198 10 *1 1.903,3.207 2.238,3.347 0.336,0.140 10 LIN2 1.005,3.207 1.326,3.347 0.322,0.140 10 LIN1 1.681,2.967 1.681,3.299 1.681,3.299 1.903,3.299 false 1.558,2.967 1.558,3.301 1.558,3.301 1.382,3.301 false

Remove the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (LIN2) - 17 (LIN1) Always Below 1 Ω
16 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Multiplex Network Master Switch Assembly)



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190820E02
4.469,1.042 4.813,1.521 true 1.375,1.01 1.656,1.49 true 3.438,2.333 3.646,2.583 true 0.677,0.115 0.865,0.26 0.188,0.146 10 false *1 0.677,1.771 0.865,1.917 0.188,0.146 10 false *3 3.583,0.115 3.771,0.26 0.188,0.146 10 false *2 4.698,1.521 5.031,1.677 0.333,0.156 10 false LIN2 1.521,1.521 1.854,1.677 0.333,0.156 10 false LIN2 3.521,2.594 3.854,2.75 0.333,0.156 10 false LIN2 4.896,0.365 5.104,0.521 0.208,0.156 10 false 2A 1.885,0.375 2.094,0.531 0.208,0.156 10 false 2D 3.406,1.813 3.656,1.969 0.25,0.156 10 false MB


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2D-26 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument Panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)
*3 Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT JUNCTION BLOCK - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT JUNCTION BLOCK - EACH ECU)
a.

Disconnect the N2*1, O2*2, L145*3, z21*4, P4 and Q4 connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-26 (LIN2) - Q4-9 (LIN) Always Below 1 Ω
2A-27 (LIN2) - P4-9 (LIN) Always Below 1 Ω
2A-27 (LIN2) - O6-17 (LIN1)*1
2A-27 (LIN2) - N13-17 (LIN1)*2
Always Below 1 Ω
2A-27 (LIN2) - N2-9 (LIN)*1
2A-27 (LIN2) - O2-9 (LIN)*2
Always Below 1 Ω
2A-27 (LIN2) - L145-9 (MPX1)*3 Always Below 1 Ω
2A-27 (LIN2) - z21-4 (MPX1)*4 Always Below 1 Ω
2D-26 (LIN2) - Body ground Always 10 kΩ or higher
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD

*3: w/ Double Locking System

*4: w/ Roof Sunshade System




OK

5.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE))
a.

Reconnect the O6*1, N13*2, L145*3, 2A, 2D, z21*4, P4, O2*1 and N2*2 connectors.

*1: for LHD

*2: for RHD

*3: w/ Double Locking System

*4: w/ Roof Sunshade System




c.

After 10 seconds have elapsed, check if the trouble occurs again.


d.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B




A

6.CHECK DTC OUTPUT (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE)

6.CHECK DTC OUTPUT (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Reconnect the Q4 connector.


b.

Disconnect the O6*1 or N13*2 connector.

*1: for LHD

*2: for RHD




d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B




A

7.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE))

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

7.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE))
a.

Reconnect the O6*1 or N13*2 connector.

*1: for LHD

*2: for RHD



b.

Disconnect the P4 connector.



d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B




A

8.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE))

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE)

8.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE))
a.

Reconnect the P4 connector.


b.

Disconnect the O2*1 or N2*2 connector.

*1: for LHD

*2: for RHD




d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B




A

9.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE))

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)

9.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE))
a.

Reconnect the O2*1 or N2*2 connector.


b.

Disconnect the N2*1 or O2*2 connector.

*1: for LHD

*2: for RHD




d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output (w/ Roof Sunshade System) A
DTC B2325 is output (w/ Double Locking System and w/o Roof Sunshade System) B
DTC B2325 is output (w/o Double Locking System and w/o Roof Sunshade System) C
DTC B2325 is not output D




A

10.CHECK DTC OUTPUT (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

B

11.CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE)

10.CHECK DTC OUTPUT (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Reconnect the N2*1 or O2*2 connector.

*1: for LHD

*2: for RHD



b.

Disconnect the z21 connector.



d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output (w/ Double Locking System) A
DTC B2325 is output (w/o Double Locking System) B
DTC B2325 is not output C




A

11.CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

11.CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Reconnect the z21*1 connector.

*1: w/ Roof Sunshade System



b.

Disconnect the L145 connector.



d.

After 10 seconds have elapsed, check if the trouble occurs again.


e.

Check for DTCs again.

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY