This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2321 | No communication between power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Power window regulator motor assembly (for driver side) ·
Main body ECU (multiplex network body ECU) ·
Multiplex network master switch assembly ·
Wire harness or connector ·
D FR DOOR fuse |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
When using the GTS to troubleshoot with the power switch off:
Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Clear the DTC (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| Only DTC B2321 is output. | A |
| DTC B1206 and B2321 are output simultaneously. | B |
When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.
A
B
Disconnect the O6*1 or N13*2 multiplex network master switch connector.
Disconnect the O2*1 or N2*2 power window regulator motor (for driver side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O6-16 (LIN2) - O2-9 (LIN)*1
N13-16 (LIN2) - N2-9 (LIN)*2 |
Always | Below 1 Ω |
| O6-16 (LIN2) - Body ground*1
N13-16 (LIN2) - Body ground*2 |
Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
OK
NG
Remove the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 16 (LIN2) - 17 (LIN1) | Always | Below 1 Ω |
| 16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| *1 | Component without harness connected
(Multiplex Network Master Switch Assembly) |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O2-2 (B) - Body ground*1
N2-2 (B) - Body ground*2 |
Power switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O2-1 (GND) - Body ground*1
N2-1 (GND) - Body ground*2 |
Always | Below 1 Ω |
*1: for LHD
*2: for RHD
| *1 | Front view of wire harness connector
(to Power Window Regulator Motor Assembly (for Driver Side)) |
| *2 | for LHD |
| *3 | for RHD |
OK
NG
Replace the power window regulator motor assembly (for driver side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).
NEXT
Clear the DTC (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
Check for DTCs.
DTC B2321 is not output.
OK
NG