Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2013.08–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2323  Rear Door RH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for rear RH side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2323 No communication between power window regulator motor assembly (for rear RH side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for rear RH side)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DOOR RR fuse



WIRING DIAGRAM

B220667E30
4.348,1.811 6.360,2.138 2.012,0.327 10 Power Window Regulator Motor Assembly (for Rear RH Side) 4.348,1.653 4.536,1.799 0.188,0.147 10 P4 4.607,0.597 4.702,0.733 0.095,0.136 10 9 2.172,0.597 2.347,0.733 0.176,0.136 10 16 3.131,0.597 3.307,0.733 0.176,0.136 10 27 5.721,0.536 5.817,0.673 0.096,0.136 10 2 5.721,1.376 5.818,1.512 0.097,0.136 10 1 4.773,0.466 5.012,0.613 0.239,0.147 10 LIN 1.789,0.466 2.102,0.613 0.313,0.147 10 LIN2 0.624,0.857 0.849,1.000 0.225,0.143 10 MB 0.624,0.989 2.273,1.318 1.649,0.329 10 Main Body ECU (Multiplex Network Body ECU) 0.545,1.643 0.744,1.796 0.200,0.153 10 2A 0.545,1.776 3.233,1.929 2.689,0.153 10 Instrument Panel Junction Block Assembly 0.445,2.482 2.066,2.635 1.621,0.153 10 : LIN Communication Line 5.564,0.466 5.680,0.613 0.115,0.147 10 B 5.354,1.289 5.706,1.436 0.352,0.147 10 GND 6.073,0.538 6.753,0.680 0.680,0.142 10 DOOR RR

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190812E02
2.042,1.698 2.667,2.219 true 5.385,1.708 6.063,2.229 true 0.24,0.156 0.448,0.323 0.208,0.167 10 false *1 4.854,0.156 5.063,0.323 0.208,0.167 10 false *2 1.917,1.167 2.156,1.313 0.24,0.146 10 false MB 5.594,0.906 5.792,1.052 0.198,0.146 10 false 2A 5.938,2.24 6.302,2.417 0.365,0.177 10 false LIN2 2.542,2.219 2.906,2.396 0.365,0.177 10 false LIN2


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument Panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the P4 power window regulator motor assembly (for rear RH side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - P4-9 (LIN) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)
a.
U190798E02
0.906,0.833 1.521,1.208 true 2.365,0.833 1.917,1.208 true 0.813,1.271 1.094,1.542 0.281,0.271 10 false P4 0.521,0.083 0.677,0.219 0.156,0.135 10 false *1 0.583,0.708 0.99,0.99 0.406,0.281 10 false GND 2.417,0.719 2.573,0.927 0.156,0.208 10 false B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P4-2 (B) - Body ground Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Power Window Regulator Motor Assembly (for Rear RH Side))



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR (for REAR RH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR (for REAR RH SIDE)
a.

Replace the power window regulator motor assembly (for rear RH side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Check for DTCs.

OK:

DTC B2323 is not output.




OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)