Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2012.03–2013.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2324  Rear Door LH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for rear LH side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2324 No communication between power window regulator motor assembly (for rear LH side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for rear LH side)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DOOR RL fuse



WIRING DIAGRAM

B220667E31
4.208,1.811 6.248,2.138 2.040,0.327 10 Power Window Regulator Motor Assembly (for Rear LH Side) 4.208,1.653 4.479,1.799 0.272,0.147 10 Q4 4.607,0.597 4.702,0.733 0.095,0.136 10 9 2.172,0.597 2.347,0.733 0.176,0.136 10 16 3.131,0.597 3.307,0.733 0.176,0.136 10 26 5.721,0.536 5.817,0.673 0.096,0.136 10 2 5.721,1.376 5.818,1.512 0.097,0.136 10 1 4.773,0.466 5.012,0.613 0.239,0.147 10 LIN 1.789,0.466 2.102,0.613 0.313,0.147 10 LIN2 0.624,0.857 0.854,1.005 0.230,0.148 10 MB 0.624,0.998 2.273,1.328 1.649,0.329 10 Main Body ECU (Multiplex Network Body ECU) 0.545,1.643 0.744,1.796 0.200,0.153 10 2D 0.545,1.776 3.425,1.929 2.880,0.153 10 Instrument Panel Junction Block Assembly 0.445,2.482 2.066,2.635 1.621,0.153 10 : LIN Communication Line 5.564,0.466 5.680,0.613 0.115,0.147 10 B 5.345,1.289 5.678,1.436 0.333,0.147 10 GND 6.073,0.538 6.753,0.680 0.680,0.142 10 DOOR RL

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190818E02
2.969,0.885 3.573,0.229 true 3.51,2.24 4.625,1.667 true 1.927,0.823 2.125,0.969 0.198,0.146 10 false 2D 1.969,0.094 2.125,0.24 0.156,0.146 10 false *1 3.625,0.125 3.938,0.271 0.313,0.146 10 false LIN2 4.677,1.594 5.01,1.74 0.333,0.146 10 false LIN2 1.969,1.521 2.125,1.667 0.156,0.146 10 false *2 0.76,2.188 0.99,2.333 0.229,0.146 10 false MB


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2D-26 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2D-26 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument Panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the Q4 power window regulator motor assembly (for rear LH side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-26 (LIN2) - Q4-9 (LIN) Always Below 1 Ω
2D-26 (LIN2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)
a.
U190799E02
0.917,0.792 1.521,1.188 true 2.354,0.813 1.906,1.188 true 0.792,1.281 1.083,1.469 0.292,0.188 10 false Q4 0.781,0.104 0.938,0.24 0.156,0.135 10 false *1 0.583,0.708 0.958,0.958 0.375,0.25 10 false GND 2.427,0.698 2.646,0.969 0.219,0.271 10 false B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q4-2 (B) - Body ground Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*1 Front view of wire harness or connector
(to Power Window Regulator Motor Assembly (for Rear LH Side))



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE)
a.

Replace the power window regulator motor assembly (for rear LH side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Check for DTCs.

OK:

DTC B2324 is not output.




OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)