Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here))


·

Combination meter sub-assembly main line or connector

·

Power source circuit of combination meter sub-assembly

·

Combination meter sub-assembly ground circuit

·

Combination meter sub-assembly



WIRING DIAGRAM

C240417E12
1.417,5.042 2.396,5.281 0.979,0.24 10 false Trouble Area 4.302,2.302 4.854,2.521 0.552,0.219 10 false DLC3 1.229,0.604 3.729,0.938 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.229,0.938 3.729,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.229,1.281 2.969,1.615 1.74,0.333 10 false : CAN Branch Line (CANH) 1.229,1.646 2.969,1.979 1.74,0.333 10 false : CAN Branch Line (CANL) 1.01,4.583 3.198,4.781 2.188,0.198 10 false Combination Meter Sub-assembly 3.365,4.594 4.063,5.135 0.698,0.542 10 false CAN No. 3 Junction Connector 1.698,3.115 1.885,3.292 0.188,0.177 10 false B 1.698,3.667 1.969,3.844 0.271,0.177 10 false IG+ 1.698,4.281 1.99,4.458 0.292,0.177 10 false ES 1.021,4.406 1.333,4.583 0.313,0.177 10 false L27 2.396,3.958 2.781,4.135 0.385,0.177 10 false CANL 2.385,3.073 2.792,3.25 0.406,0.177 10 false CANH 2.281,4.198 2.677,4.375 0.396,0.177 10 false 120 Ω 1.479,4.156 1.646,4.333 0.167,0.177 10 false 11 2.844,3.063 3.01,3.24 0.167,0.177 10 false 19 2.844,3.958 3.01,4.135 0.167,0.177 10 false 20 0.917,3.26 1.365,3.438 0.448,0.177 10 false ECU-B 0.979,3.792 1.396,3.969 0.417,0.177 10 false MET 1.479,3 1.646,3.177 0.167,0.177 10 false 1 1.479,3.552 1.646,3.729 0.167,0.177 10 false 2 4.188,4.594 4.885,5.146 0.698,0.552 10 false CAN No. 2 Junction Connector 4.99,4.594 5.698,5.177 0.708,0.583 10 false CAN No. 1 Junction Connector 6.208,4.583 6.625,4.802 0.417,0.219 10 false ECM 6.167,4.104 6.563,4.281 0.396,0.177 10 false 120 Ω 0.115,0.063 1.583,0.385 1.469,0.323 12 false V Bus (for LHD):

C240417E13
1.417,5.021 2.396,5.26 0.979,0.24 10 false Trouble Area 4.354,2.313 4.906,2.531 0.552,0.219 10 false DLC3 1.229,0.594 3.729,0.927 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.229,0.938 3.729,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.229,1.281 2.969,1.615 1.74,0.333 10 false : CAN Branch Line (CANH) 1.229,1.625 2.969,1.958 1.74,0.333 10 false : CAN Branch Line (CANL) 1.031,4.583 3.51,4.896 2.479,0.313 10 false Combination Meter Sub-assembly 3.365,4.583 4.063,5.115 0.698,0.531 10 false CAN No. 1 Junction Connector 1.698,3.115 1.885,3.292 0.188,0.177 10 false B 1.698,3.656 1.969,3.833 0.271,0.177 10 false IG+ 1.698,4.271 1.99,4.448 0.292,0.177 10 false ES 1.031,4.427 1.344,4.604 0.313,0.177 10 false L27 2.396,3.958 2.781,4.135 0.385,0.177 10 false CANL 2.385,3.073 2.792,3.25 0.406,0.177 10 false CANH 2.281,4.188 2.677,4.365 0.396,0.177 10 false 120 Ω 1.479,4.115 1.646,4.292 0.167,0.177 10 false 11 2.844,3.073 3.01,3.25 0.167,0.177 10 false 19 2.844,3.958 3.01,4.135 0.167,0.177 10 false 20 0.917,3.26 1.365,3.438 0.448,0.177 10 false ECU-B 0.979,3.802 1.396,3.979 0.417,0.177 10 false MET 1.479,2.948 1.646,3.125 0.167,0.177 10 false 1 1.479,3.5 1.646,3.677 0.167,0.177 10 false 2 4.188,4.594 4.875,5.135 0.688,0.542 10 false CAN No. 2 Junction Connector 4.99,4.583 5.698,5.156 0.708,0.573 10 false CAN No. 3 Junction Connector 6.208,4.583 6.625,4.802 0.417,0.219 10 false ECM 6.167,4.104 6.563,4.281 0.396,0.177 10 false 120 Ω 0.115,0.052 1.385,0.281 1.271,0.229 12 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 31 seconds.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER SUB-ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154716E02
2.844,2.469 3.052,2.927 false 2.719,2.469 2.333,2.927 false 0.198,0.156 0.438,0.5 0.24,0.344 10 false *a 2.802,2.948 3.26,3.115 0.458,0.167 10 false CANL 2.125,2.958 2.583,3.125 0.458,0.167 10 false CANH 1.677,0.74 1.99,0.906 0.313,0.167 10 false L27

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U154717E03
1.792,2.479 1.969,3.052 false 0.76,2.479 1.083,3.063 false 0.458,3.073 0.635,2.469 false 0.198,0.156 0.458,0.5 0.26,0.344 10 false *a 1.99,3.063 2.448,3.229 0.458,0.167 10 false ES 0.365,3.104 0.5,3.271 0.135,0.167 10 false B 1.021,3.083 1.271,3.25 0.25,0.167 10 false IG+ 1.646,0.74 1.969,0.906 0.323,0.167 10 false L27

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-11 (ES) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L27-2 (IG+) - Body ground Power switch on (IG) 11 to 14 V
L27-1 (B) - Body ground Power switch off 11 to 14 V



Result Proceed to
OK (w/o Multi-information Display) A
OK (w/ Multi-information Display) B
NG C


A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)