Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U023A No communication from the lane departure warning camera continues.
·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera



The diagnosis procedure is for when DTC U023A is output by the power management control ECU (GTS display: PM1 Gateway).

WIRING DIAGRAM

C317121E05
3.083,0.979 3.083,0.448 3.083,0.448 3.385,0.448 false 0.688,1.927 1.083,2.073 0.396,0.146 10 false 120 Ω 5.76,2.521 7.073,2.906 1.313,0.385 10 false Power Management Control ECU 6.135,1.927 6.531,2.073 0.396,0.146 10 false 120 Ω 3,3.198 3.458,3.344 0.458,0.146 10 false CA1P 2.688,4.135 4.76,4.313 2.073,0.177 10 false Lane Departure Warning Camera 5.167,4.094 6.073,4.281 0.906,0.188 10 false Trouble Area 3.115,2.99 3.271,3.135 0.156,0.146 10 false 6 3.688,2.99 3.948,3.135 0.26,0.146 10 false 12 3.698,3.563 4.125,3.75 0.427,0.188 10 false GND 2.823,3.531 3.135,3.708 0.313,0.177 10 false IGB 3.552,3.198 4.01,3.344 0.458,0.146 10 false CA1N 1.073,5.083 3.104,5.26 2.031,0.177 10 false : CAN Main Bus Line (CANH) 1.073,5.469 3.104,5.646 2.031,0.177 10 false : CAN Main Bus Line (CANL) 4.219,5.073 5.938,5.25 1.719,0.177 10 false : CAN Branch Line (CANH) 4.219,5.469 5.906,5.646 1.688,0.177 10 false : CAN Branch Line (CANL) 3.5,0.375 5.427,0.604 1.927,0.229 10 false CAN No. 4 Junction Connector 1.552,3.698 2.698,3.875 1.146,0.177 10 false ECU-IG NO. 2 2.375,4.135 2.698,4.313 0.323,0.177 10 false U13 4.135,3.448 4.333,3.625 0.198,0.177 10 false 11 2.656,3.427 2.792,3.604 0.135,0.177 10 false 7 0.042,0.021 4.823,0.208 4.781,0.188 12 false Sub Bus 11 : 0.146,2.542 1.417,3.083 1.271,0.542 10 false CAN No. 1 Junction Terminal

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 52 seconds and then drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from power management control ECU (GTS display: PM1 Gateway) B




A

2.CHECK FOR OPEN IN SUB BUS 11 LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 11 LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191153E02
2.104,1.688 2.104,0.583 2.104,0.583 2.469,0.583 false 2.104,1.979 2.104,2.594 2.104,2.594 2.469,2.594 false 0.135,0.094 0.615,0.354 0.479,0.26 10 false *a 2.51,0.5 2.99,0.76 0.479,0.26 10 false CA1P 2.521,2.51 3,2.771 0.479,0.26 10 false CA1N 0.51,1.635 0.99,1.896 0.479,0.26 10 false U13

Disconnect the U13 lane departure warning camera connector.

Text in Illustration
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U13-6 (CA1P) - U13-12 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (LANE DEPARTURE WARNING CAMERA)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191154E02
1.385,1.979 1.385,2.594 1.385,2.594 1.208,2.594 false 1.958,1.99 1.958,2.604 1.958,2.604 2.135,2.604 false 0.135,0.083 0.615,0.344 0.479,0.26 10 false *a 0.938,2.51 1.417,2.771 0.479,0.26 10 false IGB 2.198,2.521 2.677,2.781 0.479,0.26 10 false GND 0.5,1.646 0.979,1.906 0.479,0.26 10 false U13

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Lane Departure Warning Camera)

Standard Resistance:
Tester Connection Condition Specified Condition
U13-11 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U13-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)