Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Spiral cable with sensor subassembly (steering angle sensor) branch line or connector

·

Power source circuit of spiral cable with sensor subassembly (steering angle sensor)

·

Spiral cable with sensor sub-assembly (steering angle sensor) ground circuit

·

Spiral cable with sensor sub-assembly (steering angle sensor)



WIRING DIAGRAM

C356582E02
4.625,4.094 7.115,4.49 2.49,0.396 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 0.385,1.25 2.667,1.406 2.281,0.156 10 false No. 2 CAN Junction Connector 5.521,0.5 5.948,0.646 0.427,0.146 10 false CANH 5.531,0.948 5.948,1.094 0.417,0.146 10 false CANL 5.542,1.583 5.719,1.729 0.177,0.146 10 false IG 4.125,2.427 4.771,2.583 0.646,0.156 10 false ECU-B 3.875,1.677 4.896,1.854 1.021,0.177 10 false ECU-IG NO. 2 5.531,3.333 5.844,3.49 0.313,0.156 10 false ESS 5.344,1.458 5.458,1.604 0.115,0.146 10 false 5 5.344,0.844 5.458,1 0.115,0.156 10 false 3 5.354,0.406 5.469,0.563 0.115,0.156 10 false 4 5.333,3.24 5.448,3.385 0.115,0.146 10 false 2 4.365,4.104 4.833,4.271 0.469,0.167 10 false L51 5.333,2.198 5.448,2.344 0.115,0.146 10 false 6 5.531,2.292 5.823,2.448 0.292,0.156 10 false BAT 1.688,0.698 2.156,0.854 0.469,0.156 10 false 10*1 1.688,0.24 2.146,0.396 0.458,0.156 10 false 11*1 1.688,0.844 2.156,1 0.469,0.156 10 false 11*2 1.688,0.406 2.146,0.563 0.458,0.156 10 false 10*2 1.792,2.292 3.25,2.448 1.458,0.156 10 false from Auxiliary Battery 1.802,1.563 3.333,1.74 1.531,0.177 10 false from IG1 NO. 1 Relay 0.104,1.25 0.552,1.406 0.448,0.156 10 false L94 0.896,3.302 2.354,3.458 1.458,0.156 10 false *2: for RHD 0.896,3.021 2.354,3.177 1.458,0.156 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154708E02
1.323,3.073 1.625,2.469 false 1.896,2.469 2.115,3.073 false 1.594,1.104 1.875,1.26 0.281,0.156 10 false L51 0.198,0.156 0.417,0.313 0.219,0.156 10 false *a 1.042,3.115 1.427,3.292 0.385,0.177 10 false CANL 1.865,3.135 2.271,3.313 0.406,0.177 10 false CANH

Disconnect the L51 spiral cable with sensor sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L51-4 (CANH) - L51-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U154709E02
1.063,2.885 1.375,2.5 false 1.594,1.104 1.896,1.26 0.302,0.156 10 false L51 0.198,0.156 0.417,0.313 0.219,0.156 10 false *a 0.729,2.906 1.021,3.083 0.292,0.177 10 false ESS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L51-2 (ESS) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.
U191148E01
1.636,1.061 1.984,1.217 0.348,0.156 10 L51 0.194,0.184 0.413,0.340 0.218,0.156 10 *a 2.678,2.918 2.363,2.516 false 2.509,2.936 2.882,3.092 0.372,0.156 10 BAT 1.767,2.901 2.14,2.516 false 1.667,2.936 1.899,3.092 0.232,0.156 10 IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L51-5 (IG) - Body ground Power switch on (IG) 11 to 14 V
L51-6 (BAT) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)