Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C346651E08
0.552,1.167 2.563,1.427 2.01,0.26 10 false No. 1 CAN Junction Connector*1 1.604,2 3.323,2.313 1.719,0.313 10 false from EFI MAIN Relay 5.146,0.333 5.531,0.573 0.385,0.24 10 false A57 5.135,0.771 5.521,1.01 0.385,0.24 10 false A57 5.156,1.5 5.542,1.74 0.385,0.24 10 false A57 5.146,2 5.531,2.24 0.385,0.24 10 false A57 5.146,2.76 5.531,3 0.385,0.24 10 false A57 5.135,3.5 5.521,3.74 0.385,0.24 10 false D28 5.188,0.146 5.573,0.385 0.385,0.24 10 false 13 5.229,0.594 5.615,0.833 0.385,0.24 10 false 5 5.229,1.313 5.615,1.552 0.385,0.24 10 false 2 5.229,1.802 5.615,2.042 0.385,0.24 10 false 1 5.198,2.573 5.583,2.813 0.385,0.24 10 false 28 5.167,3.313 5.552,3.552 0.385,0.24 10 false 104 5.563,3.51 5.948,3.75 0.385,0.24 10 false E1 5.542,0.229 5.99,0.479 0.448,0.25 10 false CANH 5.552,0.906 6,1.156 0.448,0.25 10 false CANL 5.552,1.5 6,1.75 0.448,0.25 10 false +B 5.542,2.01 5.99,2.26 0.448,0.25 10 false +B2 5.542,2.771 6.031,3.021 0.49,0.25 10 false IGSW 5.875,4.229 6.406,4.5 0.531,0.271 10 false ECM 3.938,2.906 4.729,3.188 0.792,0.281 10 false IGN 1.969,2.76 2.938,2.979 0.969,0.219 10 false from IG2 Relay 0.25,1.167 0.646,1.375 0.396,0.208 10 false A67 1.667,0.229 2.115,0.479 0.448,0.25 10 false 1 1.667,0.667 2.115,0.917 0.448,0.25 10 false 7 5.896,0.583 6.344,0.833 0.448,0.25 10 false 120 Ω 0.542,1.479 2.552,1.74 2.01,0.26 10 false No. 3 CAN Junction Connector*2 0.25,1.479 0.646,1.688 0.396,0.208 10 false A68 0.479,3.438 2.167,3.635 1.688,0.198 10 false *1: for LHD 0.469,3.75 2.156,3.948 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154226E02
1.781,1.667 1.365,2.573 false 1.406,1.021 1.781,1.583 false 0.146,0.104 0.917,0.427 0.771,0.323 10 false *a 0.25,1.781 0.531,1.948 0.281,0.167 10 false A57 1.01,0.927 1.542,1.073 0.531,0.146 10 false CANL 1.094,2.615 1.552,2.76 0.458,0.146 10 false CANH

Disconnect the A57 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)