Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the No. 2 integration relay (EFI MAIN relay) and supplying power to either terminal +B and +B2 of the ECM.

WIRING DIAGRAM

A259022E07
0.511,2.551 1.144,2.714 0.633,0.163 10 EFI MAIN 3.569,1.895 4.202,2.057 0.633,0.163 10 EFI MAIN 0.511,5.12 1.083,5.282 0.572,0.163 10 MAIN 0.618,5.993 1.666,6.155 1.048,0.163 10 Auxiliary Battery 1.735,5.531 2.891,6.087 1.155,0.556 10 Certification ECU (Smart Key ECU Assembly) 4.06,3.598 4.318,3.760 0.258,0.163 10 IG2 1.772,3.072 2.030,3.234 0.258,0.163 10 IG2 0.532,4.535 0.957,4.698 0.424,0.163 10 P/I 1 5.175,3.072 5.457,3.234 0.282,0.163 10 IGN 6.357,5.947 6.695,6.110 0.338,0.163 10 ECM 5.758,5.046 6.031,5.208 0.273,0.163 10 D28 5.764,4.855 6.037,5.017 0.273,0.163 10 104 5.766,2.923 6.039,3.085 0.273,0.163 10 A57 5.806,2.747 6.000,2.909 0.194,0.163 10 28 5.766,2.255 6.039,2.417 0.273,0.163 10 A57 5.806,2.081 6.000,2.244 0.194,0.163 10 20 5.766,1.669 6.043,1.831 0.277,0.163 10 A57 5.848,1.49 6.042,1.653 0.194,0.163 10 6 5.766,1.23 6.039,1.392 0.273,0.163 10 A57 6.1,1.23 6.540,1.392 0.439,0.163 10 +B2 6.1,1.669 6.524,1.831 0.424,0.163 10 MREL 6.1,0.73 6.524,0.892 0.424,0.163 10 +B 6.1,2.255 6.524,2.417 0.424,0.163 10 BATT 6.1,2.923 6.505,3.085 0.404,0.163 10 IGSW 1.747,5.329 2.224,5.551 0.477,0.221 10 L195 2.758,4.738 2.952,4.901 0.194,0.163 10 9 2.306,4.862 2.663,5.024 0.357,0.163 10 IG2D 6.1,5.046 6.299,5.208 0.199,0.163 10 E1 5.848,1.051 5.954,1.214 0.106,0.163 10 1 5.766,0.728 6.039,0.891 0.273,0.163 10 A57 5.848,0.55 5.954,0.712 0.106,0.163 10 2 4.637,1.219 4.863,1.361 0.225,0.142 10 1B 4.691,1.031 4.847,1.187 0.156,0.156 10 4 4.637,1.653 4.863,1.795 0.225,0.142 10 1B 4.691,1.465 4.847,1.621 0.156,0.156 10 2 4.637,2.256 4.863,2.398 0.225,0.142 10 1B 4.691,2.068 4.847,2.224 0.156,0.156 10 1 4.637,2.928 4.863,3.070 0.225,0.142 10 1A 2.922,3.811 3.148,3.953 0.225,0.142 10 1B 3.637,3.811 3.862,3.953 0.225,0.142 10 1A 4.584,3.811 4.809,3.953 0.225,0.142 10 1A 4.691,2.74 4.847,2.896 0.156,0.156 10 4 2.716,3.811 2.871,3.967 0.156,0.156 10 3 0.317,3.81 0.542,3.952 0.225,0.142 10 1C 0.612,3.811 0.768,3.967 0.156,0.156 10 1 3.444,3.811 3.600,3.967 0.156,0.156 10 3 4.397,3.811 4.553,3.967 0.156,0.156 10 2 0.87,4.015 2.452,4.241 1.582,0.225 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D28-104 (E1) - Body ground Always Below 1 Ω




OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (IGSW VOLTAGE)
a.
U154231E03
2.25,2.104 2.25,2.979 false 0.271,0.219 0.469,0.396 0.198,0.177 10 false *a 0.323,2.01 0.604,2.177 0.281,0.167 10 false A57 2.083,2.99 2.49,3.135 0.406,0.146 10 false IGSW

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-28 (IGSW) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

3.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN RELAY)

NG

6.INSPECT NO. 2 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN RELAY)
a.

Inspect the No. 2 integration relay (EFI MAIN relay) (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)
a.

Remove the No. 2 integration relay (EFI MAIN relay) from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-4 - A57-1 (+B2) Always Below 1 Ω
1B-4 - A57-2 (+B) Always Below 1 Ω
1B-2 - A57-6 (MREL) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - BODY GROUND)
a.

Remove the No. 2 integration relay (EFI MAIN relay) from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 2 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 2 integration relay (IG2 relay) (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - ECM)
a.

Disconnect the ECM connector.


b.

Remove the No. 2 integration relay (IG2 relay) from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-4 - A57-28 (IGSW) Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - AUXILIARY BATTERY)
a.

Remove the No. 2 integration relay (IG2 relay) from the engine room relay block and junction block assembly.


b.

Disconnect the negative (-) auxiliary battery terminal.


c.

Disconnect the positive (+) auxiliary battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - Positive (+) auxiliary battery terminal Always Below 1 Ω




OK

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)
a.

Remove the No. 2 integration relay (IG2 relay) from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-3 - Body ground Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY)
a.

Remove the No. 2 integration relay (IG2 relay) from the engine room relay block and junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-9 (IG2D) - 1A-2 Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR