Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Power Steering (EPS)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C346649E09
5.042,4.229 7.031,4.479 1.99,0.25 10 false Power Steering ECU Assembly 0.469,1.333 2.448,1.625 1.979,0.292 10 false No. 2 CAN Junction Connector 5.177,0.531 5.542,0.75 0.365,0.219 10 false L54 5.177,1.052 5.542,1.271 0.365,0.219 10 false L54 5.177,2.25 5.542,2.469 0.365,0.219 10 false L54 5.146,3.365 5.51,3.583 0.365,0.219 10 false A27 5.24,3.167 5.604,3.385 0.365,0.219 10 false 2 5.229,2.063 5.594,2.281 0.365,0.219 10 false 6 5.24,0.865 5.604,1.083 0.365,0.219 10 false 7 5.24,0.333 5.604,0.552 0.365,0.219 10 false 1 5.542,0.542 6.083,0.76 0.542,0.219 10 false CANH 5.552,1.063 6.094,1.281 0.542,0.219 10 false CANL 5.542,2.25 5.906,2.469 0.365,0.219 10 false IG 5.531,3.385 5.99,3.594 0.458,0.208 10 false PGND 3.885,2.406 5,2.646 1.115,0.24 10 false ECU-IG NO. 2 1.938,2.26 3.406,2.552 1.469,0.292 10 false from IG1 NO. 1 Relay 0.146,1.333 0.51,1.552 0.365,0.219 10 false L95 1.667,0.438 2.01,0.656 0.344,0.219 10 false 3*2 1.656,0.958 2,1.177 0.344,0.219 10 false 2*2 1.656,0.813 2,1.031 0.344,0.219 10 false 3*1 1.667,0.302 2.01,0.521 0.344,0.219 10 false 2*1 0.5,3.25 2.188,3.448 1.688,0.198 10 false *1: for LHD 0.5,3.552 2.188,3.75 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 5 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154718E02
1.302,2.313 0.802,1.802 false 1.302,2.5 0.802,3.01 false 0.156,0.188 0.656,0.552 0.5,0.365 10 false *a 0.396,1.594 0.969,1.896 0.573,0.302 10 false CANH 0.417,3 1.021,3.292 0.604,0.292 10 false CANL 1.552,0.708 1.99,1.104 0.438,0.396 10 false L54

Disconnect the L54 power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L54-1 (CANH) - L54-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U154722E02
1.802,2.406 2.198,2.844 false 0.177,0.156 1.021,0.656 0.844,0.5 10 false *a 2.104,2.885 2.74,3.156 0.635,0.271 10 false PGND 1.583,0.969 1.938,1.25 0.354,0.281 10 false A27

Disconnect the A27 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (PGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.
U154719E02
2.167,2.302 2.667,2.802 false 0.156,0.135 0.656,0.5 0.5,0.365 10 false *a 2.677,2.833 3.052,3.156 0.375,0.323 10 false IG 1.563,0.708 1.906,0.927 0.344,0.219 10 false L54

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L54-6 (IG) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)