Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Hybrid Vehicle Control" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Hybrid Vehicle Control ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Hybrid vehicle control ECU branch line or connector

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU ground circuit

·

Hybrid vehicle control ECU



WIRING DIAGRAM

C354530E05
0.573,1.417 2.604,1.698 2.031,0.281 10 false No. 3 CAN Junction Connector 0.229,1.417 0.75,1.656 0.521,0.24 10 false L133 1.76,0.365 2.031,0.625 0.271,0.26 10 false 4 1.74,0.969 2.01,1.229 0.271,0.26 10 false 10 5.615,0.49 5.885,0.75 0.271,0.26 10 false L6 5.604,1.083 5.875,1.344 0.271,0.26 10 false L6 5.615,2.073 5.885,2.333 0.271,0.26 10 false L5 5.615,0.271 5.885,0.531 0.271,0.26 10 false 25 5.615,0.854 5.885,1.115 0.271,0.26 10 false 24 5.938,0.49 6.375,0.708 0.438,0.219 10 false CA1H 5.948,1.063 6.385,1.281 0.438,0.219 10 false CA1L 0.156,3 0.656,3.313 0.5,0.313 10 false L184 5.958,2.073 6.396,2.292 0.438,0.219 10 false CA2H 5.948,2.646 6.385,2.865 0.438,0.219 10 false CA2L 5.625,1.844 5.896,2.104 0.271,0.26 10 false 34 5.615,2.438 5.885,2.698 0.271,0.26 10 false 35 1.75,2.563 2.021,2.823 0.271,0.26 10 false 2 1.75,1.969 2.021,2.229 0.271,0.26 10 false 1 5.958,3.49 6.396,3.708 0.438,0.219 10 false MREL 5.573,3.5 5.844,3.76 0.271,0.26 10 false A22 5.646,3.271 5.917,3.531 0.271,0.26 10 false 6 2.26,3.49 3.281,3.708 1.021,0.219 10 false to IGCT Relay 4.052,4.104 4.875,4.323 0.823,0.219 10 false IGCT NO. 2 5.979,3.979 6.417,4.198 0.438,0.219 10 false +B1 5.969,4.406 6.406,4.625 0.438,0.219 10 false +B2 5.583,3.969 5.854,4.229 0.271,0.26 10 false A22 5.583,4.417 5.854,4.677 0.271,0.26 10 false A21 5.656,3.76 5.927,4.021 0.271,0.26 10 false 4 5.646,4.198 5.917,4.458 0.271,0.26 10 false 1 5.625,5.771 5.896,6.031 0.271,0.26 10 false L5 5.625,6.208 5.896,6.469 0.271,0.26 10 false L6 5.625,7.052 5.896,7.313 0.271,0.26 10 false L5 5.615,7.479 5.885,7.74 0.271,0.26 10 false L6 5.667,5.552 5.938,5.813 0.271,0.26 10 false 6 5.969,5.771 6.24,6.031 0.271,0.26 10 false E1 5.958,6.208 6.229,6.469 0.271,0.26 10 false E12 5.667,6 5.938,6.26 0.271,0.26 10 false 4 5.646,6.823 5.917,7.083 0.271,0.26 10 false 5 5.646,7.271 5.917,7.531 0.271,0.26 10 false 5 5.979,7.063 6.25,7.323 0.271,0.26 10 false E01 5.969,7.479 6.24,7.74 0.271,0.26 10 false E02 5.354,7.969 7.115,8.229 1.76,0.26 10 false Hybrid Vehicle Control ECU 5.615,2.656 5.885,2.917 0.271,0.26 10 false L5 0.521,3.01 2.448,3.281 1.927,0.271 10 false No. 4 CAN Junction Connector 2.094,3.958 3.323,4.188 1.229,0.229 10 false from IGCT Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HYBRID VEHICLE CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L5 and L6 hybrid vehicle control ECU connectors.


c.
U191008E02
1.406,2.656 1.76,2.594 false 1.458,3 1.813,2.583 false 2.469,2.51 2.469,3.104 2.469,3.104 2.594,3.104 false 2.427,2.51 2.427,3.104 2.427,3.104 2.188,3.104 false 1.948,0.573 2.229,0.729 0.281,0.156 10 false L5 1.073,2.938 1.594,3.115 0.521,0.177 10 false CA2H 1.073,2.583 1.458,2.76 0.385,0.177 10 false CA2L 0.156,0.052 0.594,0.385 0.438,0.333 10 false *a 2.604,0.573 2.885,0.729 0.281,0.156 10 false L6 2.635,3.021 3.021,3.198 0.385,0.177 10 false CA1L 1.792,3.021 2.313,3.198 0.521,0.177 10 false CA1H

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L6-25 (CA1H) - L6-24 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

2.CHECK ECU POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HYBRID VEHICLE CONTROL ECU)

2.CHECK ECU POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)