Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0129 No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



HINT:

This diagnostic procedure is for when DTC U0129 is output only by the hybrid vehicle control ECU (GTS display: Hybrid Control).


WIRING DIAGRAM

C346646E12
0.615,0.917 1.844,1.427 1.229,0.51 10 false No. 1 CAN Junction Connector 5.292,0.104 5.521,0.313 0.229,0.208 10 false 35 5.531,0.198 6.01,0.406 0.479,0.208 10 false CA2H 5.292,0.521 5.521,0.729 0.229,0.208 10 false 34 5.531,0.646 6.01,0.854 0.479,0.208 10 false CA2L 5.292,0.927 5.521,1.135 0.229,0.208 10 false 14 5.292,1.26 5.521,1.469 0.229,0.208 10 false 15 5.292,1.635 5.521,1.844 0.229,0.208 10 false 16 5.292,2 5.521,2.208 0.229,0.208 10 false 12 5.531,1.042 6.01,1.25 0.479,0.208 10 false BI 4.115,1.177 5.26,1.406 1.146,0.229 10 false ABS MAIN NO. 2 4.021,1.51 5.156,1.781 1.135,0.271 10 false ABS MAIN NO. 1 4.135,1.885 5.083,2.177 0.948,0.292 10 false ECU-IG NO. 2 4.406,2.25 5.24,2.542 0.833,0.292 10 false IGN 5.531,1.375 6.01,1.583 0.479,0.208 10 false BS 5.531,1.74 6.01,1.948 0.479,0.208 10 false IG1 5.531,2.104 6.01,2.313 0.479,0.208 10 false IG2 5.292,2.365 5.521,2.573 0.229,0.208 10 false 28 5.292,2.625 5.521,2.833 0.229,0.208 10 false 27 5.281,2.865 5.51,3.073 0.229,0.208 10 false 26 5.281,3.135 5.51,3.344 0.229,0.208 10 false 25 5.281,3.385 5.51,3.594 0.229,0.208 10 false 24 5.281,3.635 5.51,3.844 0.229,0.208 10 false 23 5.531,2.479 6.01,2.688 0.479,0.208 10 false GND 5.531,2.729 6.01,2.938 0.479,0.208 10 false GND2 5.531,2.979 6.01,3.188 0.479,0.208 10 false GND3 5.531,3.229 6.01,3.438 0.479,0.208 10 false GND4 5.531,3.49 6.01,3.698 0.479,0.208 10 false GND5 5.531,3.74 6.01,3.948 0.479,0.208 10 false GND6 4.906,4.188 7.083,4.583 2.177,0.396 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.604,4.198 4.927,4.396 0.323,0.198 10 false A58 0.354,0.917 0.688,1.135 0.333,0.219 10 false A67 1.677,0.094 1.906,0.302 0.229,0.208 10 false 3 1.688,0.531 1.917,0.74 0.229,0.208 10 false 9 2.219,1.01 3.656,1.26 1.438,0.25 10 false from Auxiliary Battery 2.219,1.719 3.625,1.99 1.406,0.271 10 false from IG1 NO. 1 Relay 2.615,2.083 3.646,2.333 1.031,0.25 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If the hybrid vehicle control ECU outputs DTC U0100 and DTC U0129, check the branch circuit of sub bus 15.


Result:
Result Proceed to
The hybrid vehicle control ECU outputs only DTC U0129.
(GTS display: Hybrid Control)
A
The hybrid vehicle control ECU outputs DTC U0100 and U0129.
(GTS display: Hybrid Control)
B




A

2.CHECK DTC (BRAKE SYSTEM)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK DTC (BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Result:
Result Proceed to
DTC C1241 is not output. A
DTC C1241 is output. B




A

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154755E04
1.115,2.667 1.656,2.115 false 1.99,2.656 1.76,2.115 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.594,0.885 1.896,1.042 0.302,0.156 10 false A58 0.771,2.688 1.135,2.865 0.365,0.177 10 false CA2L 1.896,2.677 2.281,2.854 0.385,0.177 10 false CA2H

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU))