The hybrid vehicle control ECU communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the hybrid vehicle control ECU does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the hybrid vehicle control ECU stores DTC U0100 or U0129.
The ECM communicates with the hybrid vehicle control ECU. When the ECM does not receive data from the hybrid vehicle control ECU, the ECM stores DTC U0293.
The brake booster with master cylinder assembly (skid control ECU) communicates with the hybrid vehicle control ECU. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0100 | The hybrid vehicle control ECU does not receive data from the ECM. | ·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of hybrid vehicle control ECU ·
Hybrid vehicle control ECU ·
Power source circuit of ECM ·
ECM ·
Open or short in No. 1 CAN junction connector ·
Open or short in No. 5 CAN junction connector |
| U0129 | The hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU). | ·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of ECM ·
ECM ·
Power source circuit of hybrid vehicle control ECU ·
Hybrid vehicle control ECU ·
Power source circuit of brake booster with master cylinder assembly (skid control ECU) ·
Brake booster with master cylinder assembly (skid control ECU) ·
Open or short in No. 1 CAN junction connector ·
Open or short in No. 5 CAN junction connector |
| U0293 | ·
The ECM does not receive data from the hybrid vehicle control ECU. ·
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU. |
·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of ECM ·
ECM ·
Power source circuit of brake booster with master cylinder assembly (skid control ECU) ·
Brake booster with master cylinder assembly (skid control ECU) ·
Open or short in No. 1 CAN junction connector ·
Open or short in No. 5 CAN junction connector |
This diagnostic procedure is for when DTC U0100, U0129 and U0293 are output at the same time.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Reconfirm DTCs.
If the hybrid vehicle control ECU outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.
| Result | Proceed to |
|---|---|
| The hybrid vehicle control ECU outputs DTC U0129 and other DTCs.
(GTS display: Hybrid Control) |
A |
| The hybrid vehicle control ECU outputs only DTC U0129.
(GTS display: Hybrid Control) |
B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L6-31 (CA3P) - L6-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω:
Short circuit between bus lines |
| 70 Ω or higher:
Open circuit in main bus lines |
|||
| L6-31 (CA3P) - L6-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
CANH ground short |
| L6-30 (CA3N) - L6-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
CANL ground short |
| L6-31 (CA3P) - L6-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
CANH +B short |
| L6-30 (CA3N) - L6-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
CANL +B short |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
When the value is as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.
If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the hybrid vehicle control ECU.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
·
NG (Ground short) ·
NG (+B short) |
D |
A
B
C
D
Disconnect the L6 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-31 (CA3P) - L6-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
OK
NG
Reconnect the L6 hybrid vehicle control ECU connector.
Disconnect the L101 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder left side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L101-2 (CANH) - L101-4 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to No. 1 CAN Junction Connector |
OK
NG
Reconnect the L101 wire harness connector to the No. 5 CAN junction connector (instrument panel connector holder left side).
Disconnect the L102 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder right side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L102-5 (CANH) - L102-3 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Hybrid Vehicle Control ECU |
OK
NG
Reconnect the L101 wire harness connector to the No. 5 CAN junction connector (instrument panel connector holder left side).
Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L132-3 (CANH) - L132-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to No. 5 CAN Junction Connector |
OK
NG
Reconnect the L132 wire harness connector to the No. 1 CAN junction connector (instrument panel wire side).
Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-4 (CANH) - A67-10 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to ECM |
OK
NG
Reconnect the A67 wire harness connector to the No. 1 CAN junction connector (engine room main wire side).
Disconnect the A57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-12 (CANP) - A57-4 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Disconnect the L6 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-31 (CA3P) - L6-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
OK
NG
Reconnect the L6 hybrid vehicle control ECU connector.
Disconnect the L102 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder right side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L102-5 (CANH) - L102-3 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Hybrid Vehicle Control ECU |
OK
NG
Disconnect the L101 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder left side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L101-2 (CANH) - L101-4 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to No. 1 CAN Junction Connector |
OK
NG
Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L132-3 (CANH) - L132-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to No. 5 CAN Junction Connector |
OK
NG
Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-3 (CANH) - A67-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A67-4 (CANH) - A67-10 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to Brake booster with master cylinder assembly (Skid control ECU) |
| *c | to ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main bus lines) | B |
| NG (Brake booster with master cylinder assembly (skid control ECU) CAN branch lines) | C |
A
B
C
Disconnect the A57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-12 (CANP) - A57-4 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-35 (CA2H) - A58-34 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the L6 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L6-31 (CA3P) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short |
| L6-30 (CA3N) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short |
| L6-31 (CA3P) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short |
| L6-30 (CA3N) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
| *1 | DLC3 | - | - |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
OK
NG
Disconnect the L102 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder right side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L102-5 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short |
| L102-3 (CANL) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short |
| L102-5 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short |
| L102-3 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Hybrid vehicle control ECU |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
OK
NG
Disconnect the L101 wire harness connector from the No. 5 CAN junction connector (instrument panel connector holder left side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L101-2 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short |
| L101-4 (CANL) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short |
| L101-2 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short |
| L101-4 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 1 CAN Junction Connector |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
OK
NG
Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L132-3 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short |
| L132-9 (CANL) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short |
| L132-3 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short |
| L132-9 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 5 CAN Junction Connector |
OK
NG
Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| A67-3 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short | Brake booster with master cylinder assembly (skid control ECU) |
| A67-9 (CANL) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| A67-4 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANH ground short | ECM |
| A67-10 (CANL) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| A67-3 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short | Brake booster with master cylinder assembly (skid control ECU) |
| A67-9 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short | |
| A67-4 (CANH) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANH +B short | ECM |
| A67-10 (CANL) - L61-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Brake booster with master cylinder assembly (Skid control ECU) |
| *c | to ECM | - | - |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| L6-31 (CA3P) - L6-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
CANH ground short |
| L6-30 (CA3N) - L6-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
CANL ground short |
| L6-31 (CA3P) - L6-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
CANH +B short |
| L6-30 (CA3N) - L6-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
CANL +B short |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
OK
NG