Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Sensor Bus)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

·

The driving support ECU assembly will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 13.

·

When the driving support ECU assembly receives a response signal from the ECUs connected to sub bus 13, the driving support ECU assembly recognizes and memorizes that the ECU is connected to sub bus 13. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to sub bus 13 when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 13, the driving support ECU assembly determines that a malfunction exists.


DTC No. DTC Detection Condition Trouble Area
U0235 No communication from the millimeter wave radar sensor assembly continues.
·

Open or short in sub bus 13 main line or connector

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


U1002 The driving support ECU assembly cannot receive signals from all ECUs that have been memorized as those connected to the sensor bus 13.
·

Open or short in sub bus 13 main line or connector

·

Driving support ECU assembly

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit



HINT:

The diagnostic procedure is for when DTC U1002 is output by the driving support ECU assembly (GTS display: Pre-crash 2).


WIRING DIAGRAM

C354527E03
0.5,1.875 2.948,2.073 2.448,0.198 10 false Driving Support ECU Assembly 0.24,1.875 0.531,2.094 0.292,0.219 10 false L60 0.698,1.177 1.396,1.396 0.698,0.219 10 false 120 Ω 6.146,1.188 6.844,1.406 0.698,0.219 10 false 120 Ω 5.146,1.844 7.021,2.344 1.875,0.5 10 false Millimeter Wave Radar Sensor Assembly 4.854,1.844 5.146,2.063 0.292,0.219 10 false A76 1.24,1.323 1.938,1.542 0.698,0.219 10 false CA1N 1.24,0.771 1.938,0.99 0.698,0.219 10 false CA1P 5.646,0.792 6.344,1.01 0.698,0.219 10 false CA1P 5.625,1.323 6.323,1.542 0.698,0.219 10 false CA1N 1.708,1.323 2.01,1.563 0.302,0.24 10 false 18 1.708,0.771 2.01,1.01 0.302,0.24 10 false 40 5.427,0.792 5.729,1.031 0.302,0.24 10 false 3 5.417,1.323 5.719,1.563 0.302,0.24 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK SUB BUS 13
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U155027E03
0.521,1.667 0.833,0.813 false 0.302,2.531 0.542,1.938 false 1.229,2.604 1.667,1.917 false 2.188,1.917 2.5,2.625 false 0.104,0.073 0.458,0.344 0.354,0.271 10 false *a 1.635,0.365 1.979,0.542 0.344,0.177 10 false L60 0.063,2.531 0.438,2.708 0.375,0.177 10 false CA1P 0.75,0.635 1.135,0.813 0.385,0.177 10 false CA1N 1.125,2.615 1.281,2.792 0.156,0.177 10 false B 2.521,2.604 2.844,2.781 0.323,0.177 10 false GND

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Component with harness connected
(Driving Support ECU Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L60-40 (CA1P) - L60-18 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
L60-40 (CA1P) - L60-25 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L60-18 (CA1N) - L60-25 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L60-40 (CA1P) - L60-30 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L60-18 (CA1N) - L60-30 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus line) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D




A

2.CHECK FOR POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

6.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (DRIVING SUPPORT ECU ASSEMBLY)

C

8.CHECK FOR SHORT IN SUB BUS 13 LINES (DRIVING SUPPORT ECU ASSEMBLY)

D

10.CHECK FOR SHORT IN SUB BUS 13 LINE (DRIVING SUPPORT ECU ASSEMBLY)
2.CHECK FOR POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Check the millimeter wave radar sensor assembly power source circuit (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>Millimeter Wave Radar Sensor Power Source Circuit).



OK

3.CHECK FOR DTC OUTPUT

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

3.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.


f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs.

Result:
Result Proceed to
DTC U1002 is not output from the driving support ECU assembly.
(GTS display: Pre-Crash 2)
A
DTC U1002 is output from the driving support ECU assembly.
(GTS display: Pre-Crash 2)
B




A

B

4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

5.CHECK FOR DTC OUTPUT
5.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs.

Result:
Result Proceed to
DTC U1002 is not output from the driving support ECU assembly.
(GTS display: Pre-Crash 2)
A
DTC U1002 is output from the driving support ECU assembly.
(GTS display: Pre-Crash 2)
B




A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

6.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U154971E02
2.813,1.906 2.542,2.51 true 2.844,1.729 2.698,0.927 true 0.49,0.917 0.833,1.094 0.344,0.177 10 false L60 2.448,0.771 2.833,0.948 0.385,0.177 10 false CA1N 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 2.323,2.542 2.708,2.719 0.385,0.177 10 false CA1P

Disconnect the L60 driving support ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-40 (CA1P) - L60-18 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

7.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
7.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the L60 driving support ECU assembly connector.


b.
U191159E01
1.553,0.276 1.927,0.414 0.373,0.139 10 A76 0.489,0.528 0.929,0.723 0.441,0.194 10 CA1N 2.458,0.546 2.929,0.795 0.471,0.249 10 CA1P 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 1.028,0.622 1.177,0.622 1.177,0.622 1.56,1.141 false 2.381,0.603 2.226,0.603 2.226,0.603 1.688,1.139 false

Disconnect the A76 millimeter wave radar sensor assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A76-3 (CA1P) - A76-2 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR

8.CHECK FOR SHORT IN SUB BUS 13 LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U154971E02
2.813,1.906 2.542,2.51 true 2.844,1.729 2.698,0.927 true 0.49,0.917 0.833,1.094 0.344,0.177 10 false L60 2.448,0.771 2.833,0.948 0.385,0.177 10 false CA1N 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 2.323,2.542 2.708,2.719 0.385,0.177 10 false CA1P

Disconnect the L60 driving support ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-40 (CA1P) - L60-18 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

9.CHECK FOR SHORT IN SUB BUS 13 LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
9.CHECK FOR SHORT IN SUB BUS 13 LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the L60 driving support ECU assembly connector.


b.
U191159E01
1.553,0.276 1.927,0.414 0.373,0.139 10 A76 0.489,0.528 0.929,0.723 0.441,0.194 10 CA1N 2.458,0.546 2.929,0.795 0.471,0.249 10 CA1P 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 1.028,0.622 1.177,0.622 1.177,0.622 1.56,1.141 false 2.381,0.603 2.226,0.603 2.226,0.603 1.688,1.139 false

Disconnect the A76 millimeter wave radar sensor assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A76-3 (CA1P) - A76-2 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR

10.CHECK FOR SHORT IN SUB BUS 13 LINE (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the L60 driving support ECU assembly connector.


b.
U154972E03
1.302,1.927 1.25,2.5 false 1.771,1.875 1.771,2.438 false 2.802,1.938 2.521,2.677 false 2.854,1.74 2.625,0.938 false 0.469,0.917 0.813,1.094 0.344,0.177 10 false L60 2.313,0.792 2.698,0.969 0.385,0.177 10 false CA1N 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 1.063,2.5 1.438,2.677 0.375,0.177 10 false GND 1.729,2.448 1.885,2.625 0.156,0.177 10 false B 2.323,2.688 2.708,2.865 0.385,0.177 10 false CA1P

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L60-40 (CA1P) - L60-25 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L60-18 (CA1N) - L60-25 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L60-40 (CA1P) - L60-30 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L60-18 (CA1N) - L60-30 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 13 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 13 inspection.





OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

11.CHECK FOR SHORT IN SUB BUS 13 LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
11.CHECK FOR SHORT IN SUB BUS 13 LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the L60 driving support ECU assembly connector.


b.
U191170E02
1.563,1.469 1.135,0.698 true 1.719,1.479 2.229,0.677 true 1.625,3.396 1.906,3 true 2.385,3.948 2.865,4.281 true 0.146,0.135 0.302,0.313 0.156,0.177 10 false *a 0.188,2.729 0.344,2.906 0.156,0.177 10 false *1 0.208,3.802 0.51,3.979 0.302,0.177 10 false L61 0.365,1.417 0.656,1.594 0.292,0.177 10 false A76 1.875,2.833 2.104,3.01 0.229,0.177 10 false CG 2.917,4.229 3.208,4.406 0.292,0.177 10 false BAT 0.854,0.521 1.406,0.698 0.552,0.177 10 false CA1N 2.198,0.521 2.583,0.698 0.385,0.177 10 false CA1P

Disconnect the A76 millimeter wave radar sensor assembly connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
A76-3 (CA1P) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
A76-2 (CA1N) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
A76-3 (CA1P) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
A76-2 (CA1N) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 13 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 13 inspection.





OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR