Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Either condition is met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera



WIRING DIAGRAM

B423566E31
4.969,3.115 5.427,3.313 0.458,0.198 10 false U13 5.375,1.74 5.656,2 0.281,0.26 10 false 7 5.333,2.396 5.583,2.708 0.25,0.313 10 false 11 5.333,0.927 5.583,1.219 0.25,0.292 10 false 12 5.375,0.406 5.625,0.667 0.25,0.26 10 false 6 5.583,2.51 6.198,2.708 0.615,0.198 10 false GND 5.594,1.823 6.208,2.021 0.615,0.198 10 false IGB 5.573,0.51 6.188,0.708 0.615,0.198 10 false CA1P 5.583,1.031 6.198,1.229 0.615,0.198 10 false CA1N 4.969,3.281 7.146,3.521 2.177,0.24 10 false Lane Departure Warning Camera 0.167,1.563 2.344,1.802 2.177,0.24 10 false No. 4 CAN Junction Connector 0.177,1.396 0.5,1.719 0.323,0.323 10 false L185 1.49,0.927 1.74,1.188 0.25,0.26 10 false 2 1.479,0.406 1.729,0.667 0.25,0.26 10 false 1 1.708,1.823 3.854,2.021 2.146,0.198 10 false from IG1 NO. 1 Relay 3.833,2 4.813,2.229 0.979,0.229 10 false ECU-IG1 NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 15 seconds, turn the lane departure alert switch on and wait at least 52 seconds and then drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191182E02
2.177,1.104 2.51,0.438 2.51,0.438 2.688,0.438 true 2.177,1.458 2.385,1.854 2.385,1.854 2.521,1.854 true 0.167,0.094 0.531,0.281 0.365,0.188 10 false *a 1.656,0.208 2,0.385 0.344,0.177 10 false U13 2.563,1.771 3.042,2.042 0.479,0.271 10 false CA1N 2.74,0.365 3.208,0.604 0.469,0.24 10 false CA1P

Disconnect the U13 lane departure warning camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U13-6 (CA1P) - U13-12 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Lane Departure Warning Camera)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (LANE DEPARTURE WARNING CAMERA)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191183E02
1.354,1.458 1.031,1.875 1.031,1.875 0.927,1.875 true 2.021,1.458 2.167,1.865 2.167,1.865 2.219,1.865 true 0.167,0.115 0.531,0.302 0.365,0.188 10 false *a 1.646,0.219 1.969,0.396 0.323,0.177 10 false U13 2.26,1.781 2.74,2.052 0.479,0.271 10 false GND 0.646,1.792 1.094,2.031 0.448,0.24 10 false IGB

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
U13-11 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U13-7 (IGB) - Body ground Power switch switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Lane Departure Warning Camera)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)