Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Central Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Central Gateway ECU Communication Stop Mode Either condition is met:
·

Communication stop for "CAN Gateway1" and/or "CAN Gateway2" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here) ).

·

Communication system DTCs (DTCs that start with U) that correspond to "Central Gateway ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Central gateway ECU (network gateway ECU) main line or connector

·

Central gateway ECU (network gateway ECU) branch line or connector

·

Power source circuit of central gateway ECU (network gateway ECU)

·

Central gateway ECU (network gateway ECU) ground circuit

·

Central gateway ECU (network gateway ECU)



WIRING DIAGRAM

C347099E12
0.469,1.042 2.458,1.302 1.99,0.26 10 false No. 2 CAN Junction Connector 5.094,4.208 7.031,4.573 1.938,0.365 10 false Central Gateway ECU (Network Gateway ECU) 5.552,3.521 6.021,3.823 0.469,0.302 10 false GND 4.729,4.219 5.198,4.521 0.469,0.302 10 false L192 5.281,0.219 5.552,0.438 0.271,0.219 10 false 18 5.292,0.656 5.563,0.875 0.271,0.219 10 false 17 5.552,0.323 6.021,0.625 0.469,0.302 10 false CA4H 5.552,0.76 6.021,1.063 0.469,0.302 10 false CA4L 5.563,1.354 6.031,1.656 0.469,0.302 10 false BATT 5.354,1.25 5.625,1.469 0.271,0.219 10 false 1 5.563,2.448 6.031,2.75 0.469,0.302 10 false IG2 5.302,1.792 5.573,2.01 0.271,0.219 10 false 11 5.292,2.333 5.563,2.552 0.271,0.219 10 false 12 5.552,1.917 6.021,2.219 0.469,0.302 10 false IG1 5.552,2.99 6.021,3.292 0.469,0.302 10 false ACC 5.333,2.885 5.604,3.104 0.271,0.219 10 false 2 5.281,3.385 5.552,3.604 0.271,0.219 10 false 10 4.219,1.5 5.208,1.729 0.99,0.229 10 false ECU-B3 4.135,3.115 4.917,3.396 0.781,0.281 10 false ECU-ACC 4.073,2.052 5.063,2.281 0.99,0.229 10 false ECU-IG NO. 2 4.365,2.583 5.042,2.896 0.677,0.313 10 false IGN 2.063,1.323 3.677,1.573 1.615,0.25 10 false from Auxiliary Battery 2.417,2.948 3.75,3.188 1.333,0.24 10 false from ACC Relay 2.104,1.875 3.594,2.146 1.49,0.271 10 false from IG1 NO. 1 Relay 2.479,2.406 3.823,2.635 1.344,0.229 10 false from IG2 Relay 0.198,1.042 0.573,1.302 0.375,0.26 10 false L95 1.667,0.229 1.938,0.448 0.271,0.219 10 false 12*2 1.667,0.656 1.979,0.885 0.313,0.229 10 false 11*2 0.115,0.073 2.104,0.333 1.99,0.26 12 false Bus 2: 1.667,0.51 1.979,0.74 0.313,0.229 10 false 12*1 1.667,0.083 1.938,0.302 0.271,0.219 10 false 11*1 0.385,2.594 2.073,2.792 1.688,0.198 10 false *1: for LHD 0.375,2.99 2.063,3.188 1.688,0.198 10 false *2: for RHD

C350460E03
5.5,0.344 6.031,0.563 0.531,0.219 10 false CA3H 5.49,1.01 6.052,1.25 0.563,0.24 10 false CA3L 5.292,0.365 5.625,0.531 0.333,0.167 10 false 6 5.229,0.802 5.563,0.969 0.333,0.167 10 false 21 1.625,0.354 1.969,0.719 0.344,0.365 10 false 1 1.625,0.781 1.969,1.135 0.344,0.354 10 false 4 5.479,1.25 6.063,1.458 0.583,0.208 10 false CAYH 5.5,1.927 6.104,2.177 0.604,0.25 10 false CAYL 5.49,4.573 5.938,4.823 0.448,0.25 10 false GND 4.979,5.292 6.917,5.719 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 4.969,5.115 5.396,5.281 0.427,0.167 10 false L192 4.135,2.552 5.01,2.719 0.875,0.167 10 false ECU-B3 3.99,3.115 4.917,3.281 0.927,0.167 10 false ECU-IG NO. 2 4.271,3.646 5.469,3.813 1.198,0.167 10 false IGN 4.104,4.188 4.979,4.354 0.875,0.167 10 false ECU-ACC 5.49,2.406 6.042,2.656 0.552,0.25 10 false BATT 5.49,2.969 6,3.313 0.51,0.344 10 false IG1 5.49,3.5 6.083,3.74 0.594,0.24 10 false IG2 5.49,4.042 5.896,4.281 0.406,0.24 10 false ACC 5.292,2.302 5.625,2.469 0.333,0.167 10 false 1 5.25,2.865 5.583,3.031 0.333,0.167 10 false 11 5.24,3.396 5.573,3.563 0.333,0.167 10 false 12 5.292,3.938 5.625,4.104 0.333,0.167 10 false 2 5.219,1.271 5.552,1.438 0.333,0.167 10 false 19 5.229,1.708 5.563,1.875 0.333,0.167 10 false 20 5.24,4.458 5.573,4.625 0.333,0.167 10 false 10 0.135,2.094 2.208,2.26 2.073,0.167 10 false No. 6 CAN Junction Connector 2.052,2.375 3.521,2.781 1.469,0.406 10 false from Auxiliary Battery 2.052,2.938 3.51,3.292 1.458,0.354 10 false from IG1 NO. 1 Relay 2.448,3.479 3.49,3.771 1.042,0.292 10 false from IG2 Relay 2.396,4.01 3.521,4.406 1.125,0.396 10 false from ACC Relay 1.625,1.25 1.958,1.417 0.333,0.167 10 false 2 1.604,1.688 2,1.917 0.396,0.229 10 false 5 0.135,1.927 0.76,2.208 0.625,0.281 10 false L200 0.115,0.094 0.708,0.385 0.594,0.292 12 false Bus 3:

C355803E04
0.115,0.073 1.219,0.313 1.104,0.24 12 false Bus 5: 0.396,1.979 2.365,2.313 1.969,0.333 10 false No. 4 CAN Junction Connector 1.854,0.354 2.958,0.594 1.104,0.24 10 false L198 1.865,0.771 2.969,1.01 1.104,0.24 10 false L198 1.875,1.24 2.979,1.479 1.104,0.24 10 false L199 1.844,1.656 2.948,1.896 1.104,0.24 10 false L199 1.969,1.469 3.073,1.708 1.104,0.24 10 false 2 1.958,1.031 3.063,1.271 1.104,0.24 10 false 1 1.979,0.583 3.083,0.823 1.104,0.24 10 false 2 1.958,0.135 3.063,0.375 1.104,0.24 10 false 1 5.74,0.24 6.844,0.479 1.104,0.24 10 false CA5H 5.719,0.906 6.823,1.146 1.104,0.24 10 false CA5L 5.708,1.823 6.813,2.063 1.104,0.24 10 false CAXL 5.729,1.135 6.833,1.375 1.104,0.24 10 false CAXH 5.438,0.25 5.948,0.531 0.51,0.281 10 false 15 5.427,0.688 5.938,0.969 0.51,0.281 10 false 16 5.51,1.115 6.021,1.396 0.51,0.281 10 false 9 5.438,1.552 5.948,1.833 0.51,0.281 10 false 24 5.146,5.229 7.104,5.667 1.958,0.438 10 false Central Gateway ECU (Network Gateway ECU) 4.76,5.24 5.865,5.479 1.104,0.24 10 false L192 5.708,4.542 6.313,4.844 0.604,0.302 10 false GND 5.719,3.458 6.323,3.76 0.604,0.302 10 false IG2 5.729,2.969 6.333,3.271 0.604,0.302 10 false IG1 5.708,4.042 6.313,4.344 0.604,0.302 10 false ACC 5.719,2.385 6.323,2.688 0.604,0.302 10 false BATT 5.469,2.25 5.729,2.458 0.26,0.208 10 false 1 5.51,3.906 5.771,4.115 0.26,0.208 10 false 2 5.438,2.823 5.698,3.031 0.26,0.208 10 false 11 5.448,3.365 5.708,3.573 0.26,0.208 10 false 12 5.448,4.417 5.708,4.625 0.26,0.208 10 false 10 4.5,3.615 5.292,3.854 0.792,0.24 10 false IGN 4.188,3.083 5.292,3.333 1.104,0.25 10 false ECU-IG NO. 2 4.302,4.156 5.406,4.406 1.104,0.25 10 false ECU-ACC 4.365,2.521 5.469,2.771 1.104,0.25 10 false ECU-B3 2.24,2.354 3.719,2.667 1.479,0.313 10 false from Auxiliary Battery 2.563,3.99 3.646,4.302 1.083,0.313 10 false from ACC Relay 2.24,2.906 3.677,3.25 1.438,0.344 10 false from IG1 NO. 1 Relay 2.656,3.448 3.729,3.854 1.073,0.406 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.
U191185E02
0.469,0.979 0.271,1.813 false 0.573,1.198 0.875,1.813 false 0.74,1.198 1.365,1.813 false 0.688,0.969 1.99,1.802 false 2.625,0.229 2.938,0.917 false 0.104,0.073 0.271,0.229 0.167,0.156 10 false *a 1.563,0.167 2.01,0.344 0.448,0.177 10 false L192 0.042,1.823 0.448,1.969 0.406,0.146 10 false BATT 0.781,1.823 1.188,1.969 0.406,0.146 10 false IG1 1.25,1.823 1.656,1.969 0.406,0.146 10 false IG2 1.885,1.823 2.292,1.969 0.406,0.146 10 false ACC 2.281,0.115 2.688,0.26 0.406,0.146 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L192-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


d.

Reconnect the cable to the negative (-) auxiliary battery terminal.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L192-1 (BATT) - Body ground Power switch off 11 to 14 V
L192-2 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
L192-11 (IG1) - Body ground Power switch on (IG) 11 to 14 V
L192-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V




OK

2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191186E02
2.25,0.104 2.177,0.104 2.177,0.104 2.177,1.125 true 2.354,0.281 2.281,0.281 2.281,0.281 2.281,0.917 true 1.198,0.229 1.51,0.229 1.51,0.229 1.51,1.135 true 1.063,0.417 1.375,0.417 1.375,0.417 1.375,1.146 true 2.833,0.417 2.771,0.417 2.771,0.417 2.771,0.917 true 2.927,1.729 2.854,1.729 2.854,1.729 2.854,1.208 true 2.104,1.896 1.917,1.896 1.917,1.896 1.917,1.208 true 2.24,1.729 2.042,1.729 2.042,1.729 2.042,1.208 true 1.594,1.896 1.792,1.896 1.792,1.896 1.792,1.208 true 1.458,1.729 1.656,1.729 1.656,1.729 1.656,1.208 true 0.094,0.063 0.26,0.219 0.167,0.156 10 false *a 1.698,0.083 2.188,0.26 0.49,0.177 10 false L192 2.292,0.031 2.688,0.177 0.396,0.146 10 false CA3L 2.385,0.208 2.781,0.354 0.396,0.146 10 false CA3H 0.802,0.135 1.198,0.281 0.396,0.146 10 false CA5L 0.635,0.323 1.031,0.469 0.396,0.146 10 false CA5H 2.865,0.344 3.313,0.49 0.448,0.146 10 false CAXH 2.948,1.656 3.344,1.802 0.396,0.146 10 false CAXL 2.292,1.656 2.698,1.802 0.406,0.146 10 false CAYL 2.177,1.813 2.583,1.958 0.406,0.146 10 false CAYH 0.958,1.656 1.365,1.802 0.406,0.146 10 false CA4L 1.094,1.813 1.5,1.958 0.406,0.146 10 false CA4H

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Line
Tester Connection Condition Specified Condition
L192-18 (CA4H) - L192-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

Bus 3 Main Line
Tester Connection Condition Specified Condition
L192-6 (CA3H) - L192-19 (CAYH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-21 (CA3L) - L192-20 (CAYL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

Bus 5 Main Line
Tester Connection Condition Specified Condition
L192-15 (CA5H) - L192-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-16 (CA5L) - L192-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Result:
Result Proceed to
OK A
NG (Bus 2 Branch line) B
NG (Bus 3 Main line) C
NG (Bus 5 Main line) D



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR OPEN IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)

D

4.CHECK FOR OPEN IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the L192 central gateway ECU (network gateway ECU) connector.


b.

Disconnect the L200 No. 6 CAN junction connector.


c.
U191213E02
1.26,1.719 1.26,1.031 1.26,1.031 1.031,1.031 true 1.979,1.719 1.979,1.073 1.979,1.073 2.25,1.073 true 1.792,1.729 1.792,0.615 1.792,0.615 2.031,0.615 true 1.448,1.729 1.448,0.615 1.448,0.615 1.229,0.615 true 0.135,0.063 0.51,0.344 0.375,0.281 10 false *a 2.083,0.542 2.917,0.854 0.833,0.313 10 false CANL*b 0.458,0.948 1.292,1.26 0.833,0.313 10 false CANH*b 0.667,0.521 1.5,0.833 0.833,0.313 10 false CANH*b 2.313,1 3.146,1.313 0.833,0.313 10 false CANL*b 0.271,1.75 0.802,1.969 0.531,0.219 10 false L200

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L200-1 (CANH) - L200-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CA3H and CA3L terminal)
L200-2 (CANH) - L200-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CAYH and CAYL terminal)




OK

REPLACE NO. 6 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the L192 central gateway ECU (network gateway ECU) connector.


b.

Disconnect the L198 and L199 No. 4 CAN junction connectors.


c.
U191203E02
0.594,2.396 0.365,2.135 0.365,2.135 0.292,2.135 true 1.563,2.375 1.969,2.375 true 0.594,2.25 0.396,1.865 0.396,1.865 0.323,1.865 true 0.781,2.177 0.813,1.625 0.813,1.625 0.75,1.625 true 0.75,2.396 0.802,3.177 0.802,3.177 0.875,3.177 true 1.323,2.302 1.208,1.948 1.208,1.948 1.135,1.948 true 1.385,2.417 1.719,2.938 1.719,2.938 1.792,2.938 true 1.563,2.219 1.875,1.875 1.875,1.875 1.948,1.875 true 2,1.802 2.625,2 0.625,0.198 10 false CANH*b 2.021,2.302 2.604,2.5 0.583,0.198 10 false CANL*b 0.167,2.042 0.354,2.26 0.188,0.219 10 false P 0.208,1.781 0.396,2 0.188,0.219 10 false B 1.844,2.865 2.052,3.052 0.208,0.188 10 false V 0.115,0.115 0.365,0.344 0.25,0.229 10 false *a 0.573,1.229 0.969,1.479 0.396,0.25 10 false L199 0.24,1.531 0.865,1.729 0.625,0.198 10 false CANH*b 0.917,3.104 1.5,3.302 0.583,0.198 10 false CANL*b 1.01,1.875 1.198,2.094 0.188,0.219 10 false B 1.375,1.552 1.771,1.802 0.396,0.25 10 false L198

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L198-1 (CANH) - L198-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CA5H and CA5L terminal)
L199-1 (CANH) - L199-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CAXH and CAXL terminal)




OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))