Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Open in Bus 3 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

No. 6 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C346805E29
0.802,4.448 2.75,4.875 1.948,0.427 10 false Central Gateway ECU (Network Gateway ECU) 0.958,1.333 1.729,1.531 0.771,0.198 10 false 120 Ω 0.969,3.792 1.74,3.99 0.771,0.198 10 false 120 Ω 1.573,0.979 2.188,1.177 0.615,0.198 10 false CA3H 1.594,1.469 2.208,1.667 0.615,0.198 10 false CA3L 1.563,3.427 2.177,3.625 0.615,0.198 10 false CAYH 1.583,3.906 2.198,4.104 0.615,0.198 10 false CAYL 2.083,0.979 2.438,1.177 0.354,0.198 10 false 6 2.104,1.458 2.417,1.656 0.313,0.198 10 false 21 2.073,3.896 2.385,4.094 0.313,0.198 10 false 20 2.073,3.427 2.385,3.625 0.313,0.198 10 false 19 5.354,0.969 5.688,1.177 0.333,0.208 10 false 1 5.354,1.458 5.74,1.688 0.385,0.229 10 false 4 5.354,3.906 5.75,4.135 0.396,0.229 10 false 5 5.354,3.438 5.75,3.656 0.396,0.219 10 false 2 4.719,4.448 5.229,4.688 0.51,0.24 10 false L200 5.104,4.448 6.979,4.906 1.875,0.458 10 false No. 6 CAN Junction Connector 0.406,4.448 0.719,4.698 0.313,0.25 10 false L192

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L200 No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

U191042E02
3.219,1.427 3.219,0.708 3.219,0.708 2.844,0.708 false 3.792,1.417 3.792,0.698 3.792,0.698 4.156,0.698 false 3.656,1.427 3.656,0.271 3.656,0.271 3.927,0.271 false 3.365,1.427 3.365,0.271 3.365,0.271 3.115,0.271 false 0.156,0.115 0.573,0.427 0.417,0.313 10 false *a 3.99,0.188 4.823,0.5 0.833,0.313 10 false CANL*b 2.271,0.625 3.104,0.938 0.833,0.313 10 false CANH*b 2.552,0.198 3.385,0.51 0.833,0.313 10 false CANH*b 4.219,0.625 5.052,0.938 0.833,0.313 10 false CANL*b 2.375,1.406 2.927,1.656 0.552,0.25 10 false L200

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L200-1 (CANH) - L200-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L200-2 (CANH) - L200-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE NO. 6 CAN JUNCTION CONNECTOR

NG

2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the L200 No. 6 CAN junction connector.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.
U191201E02
2.479,0.344 2.281,0.344 2.281,0.344 2.281,0.917 true 1.854,1.938 2.052,1.938 2.052,1.938 2.052,1.219 true 1.708,1.74 1.917,1.74 1.917,1.74 1.917,1.219 true 2.385,1.74 2.198,1.74 2.198,1.74 2.198,1.219 true 0.135,0.083 0.313,0.25 0.177,0.167 10 false *a 2.521,0.271 2.969,0.427 0.448,0.156 10 false CA3H 1.615,0.115 1.979,0.292 0.365,0.177 10 false L192 2.438,1.667 2.885,1.823 0.448,0.156 10 false CA3L 1.458,1.854 1.906,2.01 0.448,0.156 10 false CAYL 1.271,1.667 1.719,1.823 0.448,0.156 10 false CAYH

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L192-6 (CA3H) - L192-19 (CAYH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-21 (CA3L) - L192-20 (CAYL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)