There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Central gateway ECU (network gateway ECU) ·
Hybrid vehicle control ECU ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter sub-assembly ·
Brake booster with master cylinder assembly (skid control ECU) ·
Spiral cable with sensor sub-assembly (steering angle sensor) ·
Air conditioning amplifier assembly ·
Power steering ECU assembly ·
Airbag ECU assembly ·
Transmission control ECU assembly ·
Certification ECU (smart key ECU assembly) ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
No. 3 CAN junction connector |
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A57 ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-13 (CANH) - A57-5 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
OK
NG
Reconnect the A57 ECM connector.
Disconnect the L27 combination meter sub-assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-19 (CANH) - L27-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
OK
NG
Reconnect the L27 combination meter sub-assembly connector.
Disconnect the L94 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder left side).
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to No. 3 CAN Junction Connector |
| *c | to No. 1 CAN Junction Connector |
| *d | to Certification ECU (Smart Key ECU Assembly) |
| *e | to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L94-2 (CANH) - L94-1 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 3 CAN junction connector |
| L94-5 (CANH) - L94-4 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| L94-8 (CANH) - L94-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Certification ECU (Smart key ECU assembly) |
| L94-11 (CANH) - L94-10 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Spiral cable with sensor sub-assembly (Steering angle sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 CAN junction connector) | B |
| NG (Line to No. 3 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the L95 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder right side).
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to Power Steering ECU Assembly |
| *c | to Air Conditioning Amplifier Assembly |
| *d | to Airbag ECU Assembly |
| *e | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L95-2 (CANH) - L95-3 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power steering ECU assembly |
| L95-5 (CANH) - L95-6 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| L95-8 (CANH) - L95-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Airbag ECU assembly |
| L95-11 (CANH) - L95-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
OK
NG
Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to No. 2 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L132-5 (CANH) - L132-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Main body ECU (Multiplex network body ECU) |
| L132-6 (CANH) - L132-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher | No. 2 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 2 CAN junction connector) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to ECM |
| *c | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A67-1 (CANH) - A67-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| A67-2 (CANH) - A67-8 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to ECM) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the L133 wire harness connector from the No. 3 CAN junction connector (instrument panel wire side).
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to Hybrid Vehicle Control ECU |
| *c | to No. 2 CAN Junction Connector |
| *d | to Combination Meter Sub-assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L133-4 (CANH) -L133-10 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Hybrid vehicle control ECU |
| L133-5 (CANH) - L133-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher | No. 2 CAN junction connector |
| L133-6 (CANH) - L133-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Combination meter sub-assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 2 CAN junction connector) | B |
| NG (Line to combination meter subassembly) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the A68 wire harness connector from the No. 3 CAN junction connector (engine room main wire side).
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to Transmission Control ECU Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-1 (CANH) - A68-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L192-18 (CA4H) - L192-17 (CA4L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short circuited branch line or connector.
OK
NG