Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 1 CAN junction connector (engine room main wire side).

i.

Connection diagram

U154814E02
3.229,1.406 3.229,0.677 3.229,0.677 2.854,0.677 false 3.375,1.427 3.375,0.281 3.375,0.281 3.75,0.281 false 3.375,1.667 3.375,2.5 3.375,2.5 3.75,2.5 false 3.229,1.677 3.229,2.396 3.229,2.396 2.865,2.396 false 3.521,1.396 3.521,0.583 3.521,0.583 4.438,0.583 false 3.521,1.667 3.521,2.229 3.521,2.229 4.51,2.229 false 3.667,1.417 3.667,0.865 3.667,0.865 4.729,0.865 false 3.677,1.667 3.677,2.052 3.677,2.052 4.781,2.052 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.604 3.104,0.917 0.833,0.313 10 false CANH*b 2.313,2.313 3.146,2.625 0.833,0.313 10 false CANL*b 3.802,0.208 4.635,0.521 0.833,0.313 10 false CANH*c 3.781,2.427 4.615,2.74 0.833,0.313 10 false CANL*c 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.49 5.302,0.802 0.833,0.313 10 false CANH*d 4.531,2.146 5.365,2.458 0.833,0.313 10 false CANL*d 4.76,0.792 5.594,1.104 0.833,0.313 10 false CANH*e 4.813,1.969 5.646,2.281 0.833,0.313 10 false CANL*e

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to ECM
(for Bus 2)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Bus 2)
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*e to ECM
(for Sub Bus 15)
- -


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) P ECM
(for Bus 2)
A67-7 (CANL) V
A67-2 (CANH) LG Brake booster with master cylinder assembly (skid control ECU)
(for Bus 2)
A67-8 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the No. 1 CAN junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
(for Sub Bus 15)
*c Main body ECU (Multiplex Network Body ECU)
(for Bus 2)
*d to No. 2 CAN Junction Connector
(for Bus 2)


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R No. 5 CAN junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 2)
L132-11 (CANL) W
L132-6 (CANH) B No. 2 CAN junction connector
(for Bus 2)
L132-12 (CANL) W




NO. 1 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 1 CAN junction connector (engine room main wire side).

i.

Connection diagram

U191039E02
3.219,1.417 3.219,0.688 3.219,0.688 2.844,0.688 false 3.219,1.698 3.219,2.188 3.219,2.188 2.854,2.188 false 3.5,1.427 3.5,0.406 3.5,0.406 4.417,0.406 false 3.5,1.688 3.5,2.458 3.5,2.458 4.49,2.458 false 3.646,1.417 3.646,0.688 3.646,0.688 4.708,0.688 false 3.646,1.667 3.646,2.167 3.646,2.167 4.75,2.167 false 0.156,0.115 0.531,0.396 0.375,0.281 10 false *a 2.292,0.604 3.125,0.917 0.833,0.313 10 false CANH*b 2.323,2.104 3.156,2.417 0.833,0.313 10 false CANL*b 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.323 5.302,0.635 0.833,0.313 10 false CANH*c 4.542,2.375 5.375,2.688 0.833,0.313 10 false CANL*c 4.76,0.604 5.594,0.917 0.833,0.313 10 false CANH*d 4.802,2.083 5.635,2.396 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Bus 2)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*d to ECM
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) LG Brake booster with master cylinder assembly (skid control ECU)
(for Bus 2)
A67-7 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the No. 1 CAN junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
(for Sub Bus 15)
*c to No. 2 CAN Junction Connector
(for Bus 2)
*d Combination Meter Sub-assembly
(for Bus 2)


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R No. 5 CAN junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) GR No. 2 CAN junction connector
(for Bus 2)
L132-11 (CANL) W
L132-6 (CANH) SB Combination meter sub-assembly
(for Bus 2)
L132-12 (CANL) G




NO. 2 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 2 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

U154779E02
2.75,0.938 2.906,0.938 2.906,0.938 3.448,1.354 false 2.75,1.573 2.906,1.573 2.906,1.573 3.438,1.677 false 4.313,0.958 4.208,0.958 4.208,0.958 3.615,1.365 false 4.333,1.531 4.073,1.531 4.073,1.531 3.615,1.656 false 2.75,1.271 2.875,1.271 2.875,1.271 3.448,1.521 false 4.333,1.24 4.24,1.24 4.24,1.24 3.615,1.5 false 2.75,1.885 2.969,1.885 2.969,1.885 3.438,1.823 false 4.323,1.938 4.115,1.938 4.115,1.938 3.625,1.833 false 4.354,0.875 4.938,1.177 0.583,0.302 10 false CANH*b 4.354,1.469 4.938,1.771 0.583,0.302 10 false CANH*d 2.198,0.844 2.781,1.146 0.583,0.302 10 false CANL*b 4.354,1.167 4.938,1.469 0.583,0.302 10 false CANH*c 2.198,1.177 2.781,1.479 0.583,0.302 10 false CANL*c 2.198,1.49 2.781,1.792 0.583,0.302 10 false CANL*d 4.354,1.875 4.938,2.177 0.583,0.302 10 false CANH*e 2.198,1.823 2.781,2.125 0.583,0.302 10 false CANL*e 0.052,0 0.531,0.5 0.479,0.5 10 false *a 3.531,0.563 3.896,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for Bus 2)
*c to No. 1 CAN Junction Connector
(for Bus 2)
*d to Certification ECU (Smart Key ECU Assembly)
(for Bus 2)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for Bus 2)
- -


ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-2 (CANH) GR No. 3 CAN junction connector
(for Bus 2)
L94-1 (CANL) W
L94-5 (CANH) B No. 1 CAN junction connector
(for Bus 2)
L94-4 (CANL) W
L94-8 (CANH) B Certification ECU (smart key ECU assembly)
(for Bus 2)
L94-7 (CANL) W
L94-11 (CANH) B Spiral cable with sensor sub-assembly (steering angle sensor)
(for Bus 2)
L94-10 (CANL) W



b.

Check the No. 2 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

U191022E02
2.531,0.865 2.792,0.865 2.792,0.865 3.563,1.333 false 2.531,1.469 3.052,1.469 3.052,1.469 3.552,1.646 false 4.229,0.927 3.99,0.927 3.99,0.927 3.698,1.333 false 4.25,1.542 3.854,1.542 3.854,1.542 3.729,1.656 false 2.531,1.188 2.958,1.188 2.958,1.188 3.563,1.49 false 4.25,1.25 4.01,1.25 4.01,1.25 3.729,1.51 false 2.542,2.01 2.906,2.01 2.906,2.01 3.563,1.854 false 4.24,1.938 3.885,1.938 3.885,1.938 3.719,1.854 false 4.281,0.844 4.865,1.146 0.583,0.302 10 false CANL*b 4.281,1.458 4.865,1.76 0.583,0.302 10 false CANL*d 1.958,0.76 2.542,1.063 0.583,0.302 10 false CANH*b 4.281,1.177 4.865,1.479 0.583,0.302 10 false CANL*c 1.958,1.094 2.542,1.396 0.583,0.302 10 false CANH*c 1.958,1.375 2.542,1.677 0.583,0.302 10 false CANH*d 4.281,1.865 4.865,2.167 0.583,0.302 10 false CANL*e 1.979,1.927 2.563,2.229 0.583,0.302 10 false CANH*e 0.156,0.104 0.521,0.479 0.365,0.375 10 false *a 3.49,0.552 3.906,0.792 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
(for Bus 2)
*c to Air Conditioning Amplifier Assembly
(for Bus 2)
*d to Airbag ECU Assembly
(for Bus 2)
*e to Central Gateway ECU (Network Gateway ECU)
(for Bus 2)
- -


ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-2 (CANH) R Power steering ECU assembly
(for Bus 2)
L95-3 (CANL) W
L95-5 (CANH) B Air conditioning amplifier assembly
(for Bus 2)
L95-6 (CANL) W
L95-8 (CANH) B Airbag ECU assembly
(for Bus 2)
L95-9 (CANL) W
L95-11 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 2)
L95-12 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 2 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

U191020E02
2.75,0.927 2.906,0.927 2.906,0.927 3.448,1.344 false 2.75,1.563 2.906,1.563 2.906,1.563 3.438,1.667 false 4.302,0.948 4.198,0.948 4.198,0.948 3.604,1.354 false 4.323,1.542 4.063,1.542 4.063,1.542 3.604,1.667 false 2.74,1.25 2.865,1.25 2.865,1.25 3.438,1.5 false 4.313,1.24 4.219,1.24 4.219,1.24 3.594,1.5 false 2.76,1.906 2.979,1.906 2.979,1.906 3.448,1.844 false 4.302,1.938 4.094,1.938 4.094,1.938 3.604,1.833 false 4.365,0.865 4.948,1.167 0.583,0.302 10 false CANL*b 4.354,1.458 4.938,1.76 0.583,0.302 10 false CANL*d 2.198,0.833 2.781,1.135 0.583,0.302 10 false CANH*b 4.365,1.156 4.948,1.458 0.583,0.302 10 false CANL*c 2.198,1.156 2.781,1.458 0.583,0.302 10 false CANH*c 2.198,1.479 2.781,1.781 0.583,0.302 10 false CANH*d 4.354,1.854 4.938,2.156 0.583,0.302 10 false CANL*e 2.208,1.813 2.792,2.115 0.583,0.302 10 false CANH*e 0.177,0.094 0.656,0.594 0.479,0.5 10 false *a 3.51,0.563 3.875,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
(for Bus 2)
*c to No. 3 CAN Junction Connector
(for Bus 2)
*d to Certification ECU (Smart Key ECU Assembly)
(for Bus 2)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for Bus 2)
- -


ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-1 (CANH) GR No. 1 CAN junction connector
(for Bus 2)
L94-2 (CANL) W
L94-4 (CANH) B No. 3 CAN junction connector
(for Bus 2)
L94-5 (CANL) W
L94-7 (CANH) B Certification ECU (smart key ECU assembly)
(for Bus 2)
L94-8 (CANL) W
L94-10 (CANH) B Spiral cable with sensor sub-assembly (steering angle sensor)
(for Bus 2)
L94-11 (CANL) W



b.

Check the No. 2 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

U191023E02
2.531,0.865 2.792,0.865 2.792,0.865 3.563,1.333 false 2.531,1.469 3.052,1.469 3.052,1.469 3.552,1.646 false 4.229,0.938 3.99,0.938 3.99,0.938 3.698,1.344 false 4.25,1.542 3.854,1.542 3.854,1.542 3.729,1.656 false 2.531,1.198 2.958,1.198 2.958,1.198 3.563,1.5 false 4.24,1.25 4,1.25 4,1.25 3.719,1.51 false 2.542,2 2.906,2 2.906,2 3.563,1.844 false 4.24,1.938 3.885,1.938 3.885,1.938 3.719,1.854 false 4.302,0.844 4.885,1.146 0.583,0.302 10 false CANH*b 4.302,1.458 4.885,1.76 0.583,0.302 10 false CANH*d 2,0.76 2.583,1.063 0.583,0.302 10 false CANL*b 4.302,1.167 4.885,1.469 0.583,0.302 10 false CANH*c 2,1.094 2.583,1.396 0.583,0.302 10 false CANL*c 2,1.375 2.583,1.677 0.583,0.302 10 false CANL*d 4.302,1.854 4.885,2.156 0.583,0.302 10 false CANH*e 2.01,1.906 2.594,2.208 0.583,0.302 10 false CANL*e 0.135,0.115 0.5,0.49 0.365,0.375 10 false *a 3.49,0.552 3.906,0.792 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
(for Bus 2)
*c to Air Conditioning Amplifier Assembly
(for Bus 2)
*d to Airbag ECU Assembly
(for Bus 2)
*e to Central Gateway ECU (Network Gateway ECU)
(for Bus 2)
- -


ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-3 (CANH) R Power steering ECU assembly
(for Bus 2)
L95-2 (CANL) W
L95-6 (CANH) B Air conditioning amplifier assembly
(for Bus 2)
L95-5 (CANL) W
L95-9 (CANH) B Airbag ECU assembly
(for Bus 2)
L95-8 (CANL) W
L95-12 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 2)
L95-11 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 3 CAN junction connector (engine room main wire side).

i.

Connection diagram

U154816E02
3.229,1.417 3.229,0.688 3.229,0.688 2.854,0.688 false 3.229,1.698 3.229,2.417 3.229,2.417 2.865,2.417 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.615 3.104,0.927 0.833,0.313 10 false CANH*b 2.313,2.333 3.146,2.646 0.833,0.313 10 false CANL*b 2.406,1.396 2.771,1.615 0.365,0.219 10 false A68

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Transmission Control ECU Assembly
(for Bus 2)


ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) Y Transmission control ECU assembly
(for Bus 2)
A68-7 (CANL) BR



b.

Check the No. 3 CAN junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
(for Bus 2)
*c to No. 2 CAN Junction Connector
(for Bus 2)
*d to Combination Meter Sub-assembly
(for Bus 2)


ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for Bus 2)
L133-10 (CANL) P
L133-5 (CANH) GR No. 2 CAN junction connector
(for Bus 2)
L133-11 (CANL) W
L133-6 (CANH) SB Combination meter sub-assembly
(for Bus 2)
L133-12 (CANL) G




NO. 3 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 3 CAN junction connector (engine room main wire side).

i.

Connection diagram

U191040E02
3.208,1.406 3.208,0.677 3.208,0.677 2.833,0.677 false 3.219,1.677 3.219,2.396 3.219,2.396 2.854,2.396 false 3.365,1.406 3.365,0.677 3.365,0.677 3.729,0.677 false 3.365,1.677 3.365,2.396 3.365,2.396 3.729,2.396 false 0.104,0.042 0.479,0.323 0.375,0.281 10 false *a 2.292,0.583 3.125,0.896 0.833,0.313 10 false CANH*b 2.313,2.302 3.146,2.615 0.833,0.313 10 false CANL*b 2.406,1.406 2.771,1.625 0.365,0.219 10 false A68 3.781,0.594 4.344,0.906 0.563,0.313 10 false CANH*c 3.781,2.313 4.344,2.625 0.563,0.313 10 false CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b ECM
(for Bus 2)
*c to Transmission Control ECU Assembly
(for Bus 2)
- -


ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) P ECM
(for Bus 2)
A68-7 (CANL) V
A68-2 (CANH) Y Transmission control ECU assembly
(for Bus 2)
A68-8 (CANL) BR



b.

Check the No. 3 CAN junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
(for Bus 2)
*c to Main body ECU (Multiplex Network Body ECU)
(for Bus 2)
*d to No. 2 CAN Junction Connector
(for Bus 2)


ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for Bus 2)
L133-10 (CANL) P
L133-5 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 2)
L133-11 (CANL) W
L133-6 (CANH) B No. 2 CAN junction connector
(for Bus 2)
L133-12 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



i.

Connection diagram

C423692C13
0.792,1.104 0.969,1.104 0.969,1.104 1.323,1.354 true 0.844,1.719 1.031,1.719 1.031,1.719 1.323,1.563 true 0.542,0.656 0.854,0.854 0.313,0.198 10 false *a 0.448,1.667 1.052,1.875 0.604,0.208 10 false CANH 0.438,1.063 0.948,1.271 0.51,0.208 10 false CANL 2.781,0.646 3.094,0.844 0.313,0.198 10 false *b
*a Vehicle wire harness connector
connected to CAN junction connector
*b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)




b.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L199-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
L199-2 (CANL) P
L198-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
L198-2 (CANL) V
L185-1 (CANH) B Lane departure warning camera*1
(for Bus 5)
L185-2 (CANL) W
L184-1 (CANH) B Hybrid vehicle control ECU
(for Bus 5)
L184-2 (CANL) G
L183-1 (CANH) B Parking assist ECU*2
(for Bus 5)
L183-2 (CANL) L
L182-1 (CANH) B Driving support ECU assembly*3
(for Bus 5)
L182-2 (CANL) R

·

*1: w/ Lane Departure Alert System

·

*2: w/ Intelligent Parking Assist System

·

*3: w/ Pre-crash Safety System




NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

U191044E02
3.385,1.427 3.385,0.604 3.385,0.604 3.021,0.604 false 3.667,1.417 3.667,0.594 3.667,0.594 4.031,0.594 false 0.167,0.083 0.542,0.365 0.375,0.281 10 false *a 4.083,0.521 4.917,0.833 0.833,0.313 10 false CANL*b 2.385,1.396 2.75,1.615 0.365,0.219 10 false L101 2.448,0.531 3.281,0.844 0.833,0.313 10 false CANH*b

Text in Illustration
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L101-2 (CANH) R No. 1 CAN junction connector
(for Sub bus 15)
L101-4 (CANL) Y



b.

Check the No. 5 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

U154819E02
3.521,1.406 3.521,0.688 3.521,0.688 3.156,0.688 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 4.229,0.615 5.063,0.927 0.833,0.313 10 false CANH*b 2.594,0.594 3.427,0.906 0.833,0.313 10 false CANL*b 2.385,1.406 2.792,1.625 0.406,0.219 10 false L102

Text in Illustration
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L102-5 (CANH) B Hybrid vehicle control ECU
(for Sub bus 15)
L102-3 (CANL) W




NO. 6 CAN JUNCTION CONNECTOR


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

U191045E02
3.677,1.417 3.677,0.385 3.677,0.385 4.042,0.385 false 3.813,1.417 3.813,0.604 3.813,0.604 4.188,0.604 false 3.521,1.406 3.521,0.385 3.521,0.385 3.156,0.385 false 3.375,1.406 3.375,0.604 3.375,0.604 3,0.604 false 3.219,1.406 3.219,0.833 3.219,0.833 2.844,0.833 false 3.958,1.417 3.958,0.844 3.958,0.844 4.323,0.844 false 0.135,0.115 0.51,0.396 0.375,0.281 10 false *a 4.094,0.292 4.927,0.604 0.833,0.313 10 false CANL*b 4.25,0.521 5.083,0.833 0.833,0.313 10 false CANL*b 4.375,0.781 5.208,1.094 0.833,0.313 10 false CANL*c*d 2.385,1.406 2.75,1.625 0.365,0.219 10 false L200 2.458,0.302 3.292,0.615 0.833,0.313 10 false CANH*c*d 2.427,0.521 3.26,0.833 0.833,0.313 10 false CANH*b 2.292,0.75 3.125,1.063 0.833,0.313 10 false CANH*b

Text in Illustration
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
(for Bus 3)
*c to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for Bus 3)
*d to Navigation Receiver Assembly
(for Navigation Receiver Type)
(for Bus 3)


ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L200-1 (CANH) R Central gateway ECU (network gateway ECU)
(for Bus 3)
L200-4 (CANL) W
L200-2 (CANH) GR Central gateway ECU (network gateway ECU)
(for Bus 3)
L200-5 (CANL) W
L200-3 (CANH) B Radio and display receiver assembly*1
(for Bus 3)
L200-6 (CANL) W
L200-3 (CANH) B Navigation receiver assembly*2
(for Bus 3)
L200-6 (CANL) W

*1: for Radio and Display Type

*2: for Navigation Receiver Type




DLC3


a.

Measure the resistance according to the value(s) in the table below.

U154710E01
0.269,0.211 0.787,0.374 0.518,0.163 10 *1 1.574,1.596 1.848,1.768 0.274,0.172 10 L61 4.207,1.94 4.493,2.319 false 3.362,2.342 3.815,2.504 0.453,0.163 10 CANL 4.251,0.719 4.704,0.881 0.453,0.163 10 CANH 4.262,0.869 3.834,1.391 false 3.071,0.869 3.499,1.391 false 4.389,2.342 4.740,2.504 0.351,0.163 10 BAT 2.842,0.719 3.192,0.881 0.351,0.163 10 CG 3.862,1.94 3.576,2.319 false

Text in Illustration
*1 DLC3 - -

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L61-6 (CANH) - L61-4 (CG) G - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-14 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-6 (CANH) - L61-16 (BAT) G - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


U191192E02
2.74,0.844 2.99,0.844 2.99,0.844 2.99,1.302 false 2.688,1.948 2.938,1.948 2.938,1.948 2.938,1.417 false 3.198,2.427 3.458,2.427 3.458,2.427 3.458,1.417 false 4,2.083 3.802,2.083 3.802,2.083 3.802,1.417 false 3.833,0.646 3.635,0.646 3.635,0.646 3.635,1.385 false 3.302,0.406 3.552,0.406 3.552,0.406 3.552,1.385 false 4.167,0.896 3.927,0.896 3.927,0.896 3.927,1.292 false 2.99,0.667 3.24,0.667 3.24,0.667 3.24,1.292 false 3.115,2.26 3.365,2.26 3.365,2.26 3.365,1.417 false 4.083,1.927 3.885,1.927 3.885,1.927 3.885,1.427 false 3.917,2.24 3.719,2.24 3.719,2.24 3.719,1.406 false 3.031,2.073 3.281,2.073 3.281,2.073 3.281,1.417 false 1.292,1.333 1.729,1.51 0.438,0.177 10 false L192 0.167,0.115 0.323,0.292 0.156,0.177 10 false *a 2.896,0.333 3.427,0.51 0.531,0.177 10 false CA4H 3.885,0.573 4.302,0.75 0.417,0.177 10 false CA4L 2.354,0.76 2.833,0.938 0.479,0.177 10 false CAXH 2.594,0.594 3.073,0.771 0.479,0.177 10 false CA3H 2.313,1.854 2.813,2.031 0.5,0.177 10 false CAXL 2.656,1.979 3.156,2.156 0.5,0.177 10 false CA3L 2.802,2.354 3.292,2.531 0.49,0.177 10 false CAYH 2.708,2.167 3.198,2.344 0.49,0.177 10 false CAYL 4.063,2 4.583,2.177 0.521,0.177 10 false CA5H 3.958,2.167 4.479,2.344 0.521,0.177 10 false CA5L 4.125,1.844 4.615,2.021 0.49,0.177 10 false CA6H 4.219,0.802 4.656,0.979 0.438,0.177 10 false CA6L

Text in Illustration
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

U191193E02
2.344,1.76 2.344,1.125 2.344,1.125 2.156,1.125 true 4.729,1.75 4.729,1.188 4.729,1.188 4.885,1.188 true 3.625,1.896 3.635,0.531 3.635,0.531 3.427,0.531 false 3.469,1.906 3.469,0.729 3.469,0.729 3.271,0.729 false 2.948,1.781 2.948,0.938 2.948,0.938 2.76,0.938 true 3.021,1.969 3.021,2.625 3.021,2.625 2.417,2.625 true 3.156,1.969 3.156,2.854 3.156,2.854 2.729,2.854 true 3.76,1.969 3.76,3.104 3.76,3.104 3.99,3.104 true 3.917,1.99 3.917,2.896 3.917,2.896 4.146,2.896 true 3.313,1.99 3.313,3.104 3.313,3.104 3.146,3.104 true 4.667,1.979 4.667,2.542 4.667,2.542 5,2.542 true 4.063,1.99 4.063,2.729 4.063,2.729 4.521,2.729 true 4.583,1.75 4.583,0.896 4.583,0.896 4.75,0.896 true 4.146,1.729 4.146,0.698 4.146,0.698 4.313,0.698 true 0.188,0.063 0.406,0.24 0.219,0.177 10 false *a 1.292,1.979 1.76,2.219 0.469,0.24 10 false L192 1.76,1.073 2.188,1.271 0.427,0.198 10 false BATT 4.927,1.094 5.281,1.292 0.354,0.198 10 false GND 3.042,0.448 3.469,0.646 0.427,0.198 10 false CA4H 2.885,0.667 3.313,0.865 0.427,0.198 10 false CA4L 2.396,0.854 2.823,1.052 0.427,0.198 10 false CA6L 2.021,2.531 2.448,2.729 0.427,0.198 10 false CA6H 2.771,3.031 3.198,3.229 0.427,0.198 10 false CA5L 2.333,2.771 2.76,2.969 0.427,0.198 10 false CA5H 4.031,3.031 4.521,3.229 0.49,0.198 10 false CAYH 4.208,2.823 4.677,3.021 0.469,0.198 10 false CAYL 5.031,2.458 5.417,2.656 0.385,0.198 10 false CAXL 4.573,2.646 4.958,2.844 0.385,0.198 10 false CA3L 4.802,0.823 5.229,1.021 0.427,0.198 10 false CAXH 4.365,0.625 4.792,0.823 0.427,0.198 10 false CA3H

Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -

Standard Resistance:
V Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-14 (CA6H) - L192-5 (CA6L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
L192-14 (CA6H) - L192-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-5 (CA6L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-14 (CA6H) - L192-1 (BATT) G - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-5 (CA6L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-18 (CA4H) - L192-17 (CA4L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L192-18 (CA4H) - L192-10 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-17 (CA4L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-18 (CA4H) - L192-1 (BATT) L - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-17 (CA4L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-6 (CA3H) - L192-19 (CAYH) R - GR HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-21 (CA3L) - L192-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-6 (CA3H) - L192-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-21 (CA3L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-6 (CA3H) - L192-1 (BATT) R - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-21 (CA3L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-15 (CA5H) - L192-9 (CAXH) B - B HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-16 (CA5L) - L192-24 (CAXL) V - P LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-15 (CA5H) - L192-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-16 (CA5L) - L192-10 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-15 (CA5H) - L192-1 (BATT) B - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-16 (CA5L) - L192-1 (BATT) V - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU


Refer to Terminals of ECU (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191188E02
2.458,2.438 1.729,2.073 false 2.406,2.448 1.646,2.406 false 2.677,2.313 2.177,1.833 false 1.698,2.708 2.417,2.51 false 1.99,3.031 2.458,2.51 false 1.823,1.01 1.573,0.51 false 2.552,3.031 2.917,3.25 0.365,0.219 10 false L6 1.51,1.896 1.948,2.156 0.438,0.26 10 false CA1L 1.24,2.333 1.688,2.583 0.448,0.25 10 false CA1H 1.302,2.656 1.75,2.917 0.448,0.26 10 false CA3P 1.729,3.073 2.125,3.323 0.396,0.25 10 false CA3N 0.073,0 0.271,0.167 0.198,0.167 10 false *a 1.99,1.656 2.375,1.917 0.385,0.26 10 false BATT 1.469,0.344 1.698,0.563 0.229,0.219 10 false E1 1.99,0.375 2.344,0.615 0.354,0.24 10 false L5

Disconnect the L6 hybrid vehicle control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-25 (CA1H) - L6-24 (CA1L) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L6-25 (CA1H) - L5-6 (E1) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-24 (CA1L) - L5-6 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-25 (CA1H) - L6-3 (BATT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-24 (CA1L) - L6-3 (BATT) P - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L6-31 (CA3P) - L5-6 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-30 (CA3N) - L5-6 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-31 (CA3P) - L6-3 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-30 (CA3N) - L6-3 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.
U191007E03
1.771,2.375 1.094,2.208 true 1.417,2.635 1.771,2.583 true 1.469,3 1.823,2.583 true 2.698,2.344 2.698,1.875 2.698,1.875 2.458,1.875 true 1.948,3 2.229,3.156 0.281,0.156 10 false L5 0.896,2.104 1.083,2.281 0.188,0.177 10 false E1 1.083,2.948 1.604,3.125 0.521,0.177 10 false CA2H 1.063,2.563 1.448,2.74 0.385,0.177 10 false CA2L 0.156,0.021 0.594,0.354 0.438,0.333 10 false *a 2.604,3 2.885,3.156 0.281,0.156 10 false L6 2.083,1.802 2.667,1.979 0.583,0.177 10 false BATT

Disconnect the L5 hybrid vehicle control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 5 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) B - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L5-34 (CA2H) - L5-6 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-35 (CA2L) - L5-6 (E1) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-34 (CA2H) - L6-3 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L5-35 (CA2L) - L6-3 (BATT) G - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A57 and D28 ECM connectors.

U154723E01
0.18,0.166 0.643,0.516 0.462,0.349 10 *a 3.109,1.531 3.405,1.704 0.296,0.172 10 D28 5.113,1.799 5.399,2.364 false 2.207,0.746 2.660,0.909 0.453,0.163 10 CANL 2.26,2.159 2.713,2.322 0.453,0.163 10 CANH 0.826,2.138 1.223,2.301 0.397,0.163 10 BATT 5.335,2.366 5.580,2.528 0.244,0.163 10 E1 0.517,1.514 0.848,1.686 0.331,0.172 10 A57 1.644,1.496 1.213,2.114 false 1.328,2.16 1.731,2.341 0.403,0.181 10 CANP 1.126,0.743 1.536,0.924 0.411,0.181 10 CANN 1.964,1.352 2.19,0.896 false 1.893,1.352 1.554,0.901 false 1.976,1.414 2.249,2.141 false 1.897,1.426 1.726,2.141 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-13 (CANH) - D28-104 (E1) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-5 (CANL) - D28-104 (E1) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-13 (CANH) - A57-20 (BATT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-5 (CANL) - A57-20 (BATT) V - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-12 (CANP) - D28-104 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-4 (CANN) - D28-104 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-12 (CANP) - A57-20 (BATT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-4 (CANN) - A57-20 (BATT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TRANSMISSION CONTROL ECU ASSEMBLY


Refer to Terminals of ECU (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154768E02
2.073,1.688 1.802,2.156 false 2.167,1.698 2.438,2.177 false 2.104,3.719 2.521,4.146 false 1.208,1.354 0.906,0.99 false 0.052,0 0.406,0.375 0.354,0.375 10 false *a 0.5,1.448 0.927,1.792 0.427,0.344 10 false A24 0.51,3.51 0.927,3.844 0.417,0.333 10 false A23 2.479,2.198 2.885,2.375 0.406,0.177 10 false CA1H 1.406,2.198 1.792,2.375 0.385,0.177 10 false CA1L 2.552,4.156 2.927,4.333 0.375,0.177 10 false BATT 0.677,0.792 0.865,0.969 0.188,0.177 10 false E1

Disconnect the A23 and A24 transmission control ECU assembly connectors.

Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Y - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A24-16 (CA1H) - A24-1 (E1) Y - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-15 (CA1L) - A24-1 (E1) BR - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-16 (CA1H) - A23-15 (BATT) Y - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A24-15 (CA1L) - A23-15 (BATT) BR - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154754E02
2.656,1.729 2.948,1 false 1.115,2.688 1.656,2.135 false 1.615,2.677 1.76,2.135 false 1.958,2.125 2.042,2.667 false 2.063,2.125 2.448,2.667 false 2.646,2.042 2.948,2.802 false 0.198,0.156 0.469,0.406 0.271,0.25 10 false *a 0.271,0.885 0.563,1.042 0.292,0.156 10 false A58 2.938,0.823 3.167,0.979 0.229,0.156 10 false BS 2.927,2.813 3.25,2.99 0.323,0.177 10 false GND 0.771,2.708 1.135,2.885 0.365,0.177 10 false CA2L 1.302,2.698 1.688,2.875 0.385,0.177 10 false CA2H 1.802,2.708 2.188,2.885 0.385,0.177 10 false CA1H 2.333,2.698 2.698,2.875 0.365,0.177 10 false CA1L

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-37 (CA1H) - A58-38 (CA1L) LG - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-37 (CA1H) - A58-28 (GND) LG - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-38 (CA1L) - A58-28 (GND) L - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-37 (CA1H) - A58-15 (BS) LG - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-38 (CA1L) - A58-15 (BS) L - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-35 (CA2H) - A58-28 (GND) P - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-34 (CA2L) - A58-28 (GND) V - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-35 (CA2H) - A58-15 (BS) P - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-34 (CA2L) - A58-15 (BS) V - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L16 airbag ECU assembly connector.

U191001E02
1.208,1.156 1.5,1.635 false 1.417,1.854 1.198,2.323 false 1.688,1.875 1.604,2.229 false 5.719,1.938 5.927,2.344 false 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 0.99,2.333 1.438,2.5 0.448,0.167 10 false CANL 1,1 1.448,1.167 0.448,0.167 10 false CANH 1.521,2.26 1.719,2.427 0.198,0.167 10 false E1 5.854,2.354 6.208,2.521 0.354,0.167 10 false BAT 0.625,1.594 1.073,1.885 0.448,0.292 10 false L16 3.396,0.156 3.896,0.323 0.5,0.167 10 false *1 3.396,1.635 3.823,1.906 0.427,0.271 10 false L61

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L16-13 (CANH) - L16-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L16-13 (CANH) - L16-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-22 (CANL) - L16-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-13 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L16-22 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.

U191126E02
2.438,0.354 2.323,0.354 2.323,0.354 1.844,1.302 true 2.646,0.635 2.479,0.635 2.479,0.635 1.917,1.302 true 6.719,1.792 6.573,1.792 6.573,1.792 6.25,1.615 true 5.927,0.51 5.677,0.51 5.677,0.51 5.521,1.083 true 0.146,0.104 0.417,0.406 0.271,0.302 10 false *a 3.865,0.115 4.333,0.406 0.469,0.292 10 false *1 6.771,1.708 7.063,1.885 0.292,0.177 10 false BAT 4.125,1.313 4.448,1.531 0.323,0.219 10 false L61 1.552,0.479 1.896,0.75 0.344,0.271 10 false L201 2.49,0.271 2.875,0.448 0.385,0.177 10 false CANL 2.688,0.552 3.094,0.729 0.406,0.177 10 false CANH 5.969,0.438 6.375,0.615 0.406,0.177 10 false CG

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L201-14 (CANH) - L201-13 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L201-14 (CANH) - L61-4 (CG) SB - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-13 (CANL) - L61-4 (CG) W- G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-14 (CANH) - L61-16 (BAT) SB - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L201-13 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)


U190989E01
0.138,0.035 0.601,0.385 0.462,0.349 10 *a 3.963,1.367 4.416,1.530 0.453,0.163 10 CANL 2.75,1.402 3.203,1.565 0.453,0.163 10 CANH 3.496,0.234 3.828,0.407 0.331,0.172 10 L51 3.204,1.474 3.506,1.102 false 3.671,1.106 3.92,1.449 false

Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154707E01
1.59,1.064 1.941,1.269 0.351,0.206 10 L51 0.194,0.153 0.529,0.425 0.335,0.273 10 *a 0.727,2.907 1.022,3.088 0.295,0.181 10 ESS 1.042,3.115 1.429,3.296 0.387,0.181 10 CANL 1.662,3.111 2.073,3.292 0.411,0.181 10 CANH 2.711,2.902 2.998,3.083 0.287,0.181 10 BAT 1.063,2.884 1.38,2.496 false 1.319,3.07 1.628,2.467 false 1.895,2.467 1.948,3.076 false 2.396,2.467 2.711,2.878 false

Disconnect the L51 spiral cable with sensor sub-assembly (steering angle sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L51-4 (CANH) - L51-3 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L51-4 (CANH) - L51-2 (ESS) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-3 (CANL) - L51-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-4 (CANH) - L51-6 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L51-3 (CANL) - L51-6 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 and L54 power steering ECU assembly connectors.

U154726E01
0.166,0.148 2.563,0.497 2.397,0.349 10 *a 2.248,2.449 2.701,2.612 0.453,0.163 10 CANL 1.292,2.449 1.745,2.612 0.453,0.163 10 CANH 5.299,1.023 5.625,1.186 0.325,0.163 10 PIG 5.215,2.357 5.647,2.519 0.432,0.163 10 PGND 1.115,1.631 1.437,1.803 0.323,0.172 10 L54 1.966,1.891 1.513,2.414 false 1.979,2.065 2.403,2.414 false 4.93,1.588 5.382,1.183 false 4.93,1.912 5.382,2.316 false 3.909,1.643 4.232,1.815 0.323,0.172 10 A27

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L54-1 (CANH) - L54-7 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L54-1 (CANH) - A27-2 (PGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-7 (CANL) - A27-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-1 (CANH) - A27-1 (PIG) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L54-7 (CANL) - A27-1 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

U191171E02
2.01,0.854 2.271,0.854 2.271,0.854 2.271,1.531 false 2.594,0.865 2.354,0.865 2.354,0.865 2.354,1.542 false 5.104,0.854 5.323,0.854 5.323,0.854 5.323,1.375 false 4.021,1.698 4.385,1.698 false 0.156,0 0.354,0.198 0.198,0.198 10 false *a 4.885,0.771 5.156,1.01 0.271,0.24 10 false +B 3.885,1.615 4.104,1.875 0.219,0.26 10 false E 2.646,0.781 3.125,1.021 0.479,0.24 10 false CANL 1.594,0.771 2.073,1.042 0.479,0.271 10 false CANH 2.021,0.396 2.438,0.677 0.417,0.281 10 false L197 4.74,0.448 5.146,0.719 0.406,0.271 10 false L195

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L197-14 (CANH) - L197-15 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L197-14 (CANH) - L195-11 (E) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-15 (CANL) - L195-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-14 (CANH) - L195-2 (+B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L197-15 (CANL) - L195-2 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L35 and L167 radio and display receiver assembly connectors.

U191095E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.792,0.521 5.635,0.521 5.635,0.521 5.635,1.5 true 5.198,2.302 5.031,2.302 5.031,2.302 5.031,1.906 true 0.135,0.094 0.313,0.271 0.177,0.177 10 false *a 2.385,0.49 2.823,0.667 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.229 5.677,2.417 0.448,0.188 10 false GND1 0.688,1.521 0.969,1.698 0.281,0.177 10 false L35 3.917,1.531 4.354,1.708 0.438,0.177 10 false L167

Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L35-9 (CANH) - L35-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L35-9 (CANH) - L167-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-10 (CANL) - L167-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-9 (CANH) - L167-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L35-10 (CANL) - L167-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


Refer to Terminals of ECU (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L38 and L171 navigation receiver assembly connectors.

U191096E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.813,0.521 5.656,0.521 5.656,0.521 5.656,1.5 true 5.198,2.271 5.031,2.271 5.031,2.271 5.031,1.875 true 0.135,0.125 0.313,0.302 0.177,0.177 10 false *a 2.375,0.479 2.813,0.656 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.198 5.677,2.385 0.448,0.188 10 false GND1 0.688,1.531 0.969,1.708 0.281,0.177 10 false L38 3.917,1.531 4.365,1.719 0.448,0.188 10 false L171

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L38-9 (CANH) - L38-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L38-9 (CANH) - L171-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-10 (CANL) -L171-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-9 (CANH) - L171-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L38-10 (CANL) - L171-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER SUB-ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L27 combination meter sub-assembly connector.

U154724E02
3.625,2 3.875,2.365 false 4.76,0.969 4.615,0.969 4.615,0.969 4.385,1.948 false 4.75,1.344 4.667,1.344 4.667,1.344 4.479,1.948 false 2.292,1.229 2.375,1.229 2.375,1.229 2.677,1.958 false 0.219,0.177 2.615,0.531 2.396,0.354 10 false *a 4.792,1.25 5.24,1.417 0.448,0.167 10 false CANL 4.792,0.885 5.24,1.052 0.448,0.167 10 false CANH 2.167,1.135 2.344,1.302 0.177,0.167 10 false B 3.844,2.406 4.094,2.573 0.25,0.167 10 false ES 1.813,1.75 2.135,1.927 0.323,0.177 10 false L27

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) SB - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L27-19 (CANH) - L27-11 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-20 (CANL) - L27-11 (ES) G - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-19 (CANH) - L27-1 (B) SB - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L27-20 (CANL) - L27-1 (B) G - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L17 air conditioning amplifier assembly connector.

U154725E01
0.22,0.181 2.617,0.530 2.397,0.349 10 *a 4.352,0.909 4.805,1.072 0.453,0.163 10 CANL 2.626,0.909 3.079,1.072 0.453,0.163 10 CANH 2.342,2.471 2.517,2.634 0.175,0.163 10 B 4.141,2.471 4.573,2.634 0.432,0.163 10 GND 1.825,1.788 2.148,1.960 0.323,0.172 10 L17 3.65,1.962 3.06,1.072 false 3.746,1.962 4.336,1.072 false 2.702,2.091 2.415,2.46 false 4.281,2.46 3.927,1.964 false

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L17-11 (CANH) - L17-14 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-12 (CANL) - L17-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-11 (CANH) - L17-21 (B) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L17-12 (CANL) - L17-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


Refer to Terminals of ECU (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191155E03
2.823,1.906 2.688,2.729 false 2.844,1.75 2.698,0.948 false 2.698,1.906 2.115,2.729 false 2.719,1.75 2.135,1 false 1.76,1.896 1.51,2.729 false 1.302,1.906 0.917,2.719 false 0.49,0.927 0.854,1.135 0.365,0.208 10 false L60 2.51,0.771 2.927,1 0.417,0.229 10 false CA1N 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 2.521,2.771 2.99,3 0.469,0.229 10 false CA1P 1.948,0.813 2.333,1.052 0.385,0.24 10 false CA2L 1.917,2.781 2.354,3.01 0.438,0.229 10 false CA2H 1.448,2.771 1.688,2.99 0.24,0.219 10 false B 0.74,2.75 1.198,2.99 0.458,0.24 10 false GND

Disconnect the L60 driving support ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 5 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-39 (CA2H) - L60-17 (CA2L) B - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L60-39 (CA2H) - L60-25 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-17 (CA2L) - L60-25 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-39 (CA2H) - L60-30 (B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L60-17 (CA2L) - L60-30 (B) R - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 13 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-40 (CA1P) - L60-18 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L60-40 (CA1P) - L60-25 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-18 (CA1N) - L60-25 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-40 (CA1P) - L60-30 (B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L60-18 (CA1N) - L60-30 (B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Intelligent Parking Assist System)


Refer to Terminals of ECU (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191128E01
0.071,0.06 0.283,0.260 0.212,0.200 10 *a 2.224,0.341 2.498,0.518 0.273,0.177 10 L65 1.576,2.716 1.849,2.893 0.273,0.177 10 L64 1.939,1.897 2.331,2.056 0.392,0.159 10 CANL 2.114,2.24 2.566,2.394 0.452,0.154 10 CANH 2.77,2.709 3.185,2.863 0.415,0.154 10 GND1 0.311,2.686 0.529,2.841 0.218,0.154 10 +B 2.394,1.969 2.462,1.969 2.462,1.969 2.604,1.483 false 2.615,2.315 2.683,2.315 2.683,2.315 2.727,1.482 false 2.746,2.799 2.674,2.799 2.674,2.799 2.483,3.355 false 0.559,2.78 0.638,2.78 0.638,2.78 0.916,3.355 false

Disconnect the L64 and L65 parking assist ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) B - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L65-40 (CANH) - L64-4 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-39 (CANL) - L64-4 (GND1) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-40 (CANH) - L64-1 (+B) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L65-39 (CANL) - L64-1 (+B) L - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


U191365E03
2.313,0.844 2.625,1.083 0.313,0.24 10 false A76 0.146,0.031 0.427,0.188 0.281,0.156 10 false *a

Text in Illustration
*a Component without harness connected
(Millimeter Wave Radar Sensor Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191168E04
1.667,1.365 2.396,0.75 false 1.542,1.354 0.708,0.729 false 1.375,1.396 0.76,1.406 false 2.458,4.052 2.885,4.25 false 0.115,0.104 0.5,0.479 0.385,0.375 10 false *a 0.313,0.573 0.802,0.854 0.49,0.281 10 false CA1N 2.448,0.604 2.938,0.885 0.49,0.281 10 false CA1P 0.333,1.333 0.823,1.615 0.49,0.281 10 false SGND 2.948,4.26 3.406,4.615 0.458,0.354 10 false BAT 1.531,0.458 1.823,0.635 0.292,0.177 10 false A76 1.573,2.604 1.917,2.813 0.344,0.208 10 false L61 0.115,2.24 0.5,2.615 0.385,0.375 10 false *1

Disconnect the A76 millimeter wave radar sensor assembly connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A76-3 (CA1P) - A76-2 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A76-3 (CA1P)- A76-1 (SGND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-2 (CA1N) - A76-1 (SGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-3 (CA1P) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A76-2 (CA1N) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


Refer to Terminals of ECU (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191169E02
2.552,1.365 2.438,1.365 2.438,1.365 2.073,1.479 false 1.479,2.302 1.74,2.302 1.74,2.302 1.896,1.854 false 2.563,2.083 2.448,2.083 2.448,2.083 2.083,1.844 false 2.708,4.396 2.594,4.396 2.594,4.396 2.448,4.031 false 1.531,2.615 1.948,2.875 0.417,0.26 10 false L61 1.531,0.573 1.875,0.854 0.344,0.281 10 false U13 2.625,1.281 3.135,1.594 0.51,0.313 10 false CA1P 2.615,2 3.094,2.292 0.479,0.292 10 false CA1N 0.146,2.25 0.5,2.542 0.354,0.292 10 false *1 0.146,0.167 0.531,0.458 0.385,0.292 10 false *a 1.135,2.24 1.594,2.479 0.458,0.24 10 false GND 2.781,4.313 3.229,4.469 0.448,0.156 10 false BAT

Disconnect the U13 lane departure warning camera connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U13-6 (CA1P) - U13-12 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
U13-6 (CA1P) - U13-11 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U13-12 (CA1N) - U13-11 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U13-6 (CA1P) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
U13-12 (CA1N) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher