Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 2 Line for Short to +B (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

Central gateway ECU (network gateway ECU)

·

Hybrid vehicle control ECU

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter sub-assembly

·

Brake booster with master cylinder assembly (skid control ECU)

·

Spiral cable with sensor sub-assembly (steering angle sensor)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (smart key ECU assembly)

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

No. 3 CAN junction connector



WIRING DIAGRAM

C356565E02
2.573,8.438 4.563,8.625 1.99,0.188 10 false No. 2 CAN Junction Connector 2.771,3.99 4.76,4.177 1.99,0.188 10 false No. 3 CAN Junction Connector 0.385,5.51 1.833,5.76 1.448,0.25 10 false Airbag ECU Assembly 5.885,7.5 6.292,7.667 0.406,0.167 10 false CA4L 5.865,6.969 6.302,7.135 0.438,0.167 10 false CA4H 5.875,2.781 6.281,2.948 0.406,0.167 10 false CA1L 5.885,2.26 6.323,2.427 0.438,0.167 10 false CA1H 5.875,0.708 6.281,0.875 0.406,0.167 10 false CANL 5.875,0.167 6.313,0.333 0.438,0.167 10 false CANH 0.813,7.5 1.219,7.667 0.406,0.167 10 false CANL 0.792,6.958 1.229,7.125 0.438,0.167 10 false CANH 0.823,5.063 1.229,5.229 0.406,0.167 10 false CANL 0.781,4.521 1.219,4.688 0.438,0.167 10 false CANH 4.031,7 4.313,7.167 0.281,0.167 10 false L95 4.031,7.531 4.313,7.698 0.281,0.167 10 false L95 4.052,4.552 4.323,4.719 0.271,0.167 10 false L94 4.052,5.083 4.323,5.25 0.271,0.167 10 false L94 4.021,3.771 4.344,3.938 0.323,0.167 10 false L133 4.042,0.823 4.396,0.99 0.354,0.167 10 false A68 4.042,0.302 4.417,0.469 0.375,0.167 10 false A68 4.01,3.313 4.417,3.479 0.406,0.167 10 false L133 2.917,7 3.167,7.167 0.25,0.167 10 false L94 2.927,7.531 3.188,7.698 0.26,0.167 10 false L94 2.927,4.552 3.188,4.719 0.26,0.167 10 false L95 2.927,5.083 3.188,5.25 0.26,0.167 10 false L95 1.302,6.865 1.51,7.031 0.208,0.167 10 false 14 2.99,7.333 3.104,7.5 0.115,0.167 10 false 8 2.979,6.792 3.094,6.958 0.115,0.167 10 false 7 1.302,7.417 1.625,7.583 0.323,0.167 10 false 15 1.302,4.427 1.49,4.594 0.188,0.167 10 false 13 2.99,4.885 3.104,5.052 0.115,0.167 10 false 8 4.125,4.354 4.24,4.521 0.115,0.167 10 false 4 4.115,4.896 4.229,5.063 0.115,0.167 10 false 5 2.99,4.354 3.104,4.521 0.115,0.167 10 false 9 1.323,4.969 1.51,5.135 0.188,0.167 10 false 22 0.063,7.958 0.458,8.125 0.396,0.167 10 false L197 5.615,6.875 5.854,7.042 0.24,0.167 10 false 18 4.063,7.344 4.25,7.51 0.188,0.167 10 false 11 4.094,3.573 4.281,3.74 0.188,0.167 10 false 12 4.146,0.625 4.333,0.792 0.188,0.167 10 false 7 4.135,3.104 4.323,3.271 0.188,0.167 10 false 6 4.146,0.083 4.333,0.25 0.188,0.167 10 false 1 4.052,6.792 4.24,6.958 0.188,0.167 10 false 12 5.594,7.406 6,7.573 0.406,0.167 10 false 17 5.615,2.146 5.802,2.313 0.188,0.167 10 false 16 4.135,2.083 4.323,2.25 0.188,0.167 10 false 2 4.146,2.604 4.333,2.771 0.188,0.167 10 false 8 5.625,2.677 5.813,2.844 0.188,0.167 10 false 15 5.625,0.167 5.813,0.333 0.188,0.167 10 false 13 5.677,0.708 5.781,0.875 0.104,0.167 10 false 5 0.073,5.51 0.354,5.677 0.281,0.167 10 false L16 4.031,2.281 4.313,2.448 0.281,0.167 10 false A68 4.042,2.813 4.323,2.979 0.281,0.167 10 false A68 5.458,3.24 5.74,3.406 0.281,0.167 10 false A24 6.385,0.521 6.896,0.708 0.51,0.188 10 false 120 Ω 0.438,7.958 2.198,8.333 1.76,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.208,7.958 5.604,8.135 0.396,0.177 10 false L192 5.563,7.958 7.135,8.385 1.573,0.427 10 false Central Gateway ECU (Network Gateway ECU) 5.771,3.24 7.115,3.917 1.344,0.677 10 false Transmission Control ECU Assembly 6.052,1.24 6.323,1.438 0.271,0.198 10 false A57 6.375,1.24 6.719,1.438 0.344,0.198 10 false ECM 0.333,1.25 1.729,1.76 1.396,0.51 10 false Hybrid Vehicle Control ECU 0.854,0.844 1.26,1.01 0.406,0.167 10 false CA1L 0.823,0.292 1.26,0.458 0.438,0.167 10 false CA1H 2.906,0.302 3.281,0.469 0.375,0.167 10 false L133 2.906,0.833 3.271,1 0.365,0.167 10 false L133 0.094,1.25 0.333,1.417 0.24,0.167 10 false L6 3.021,0.083 3.208,0.25 0.188,0.167 10 false 4 2.979,0.625 3.167,0.792 0.188,0.167 10 false 10 1.302,0.156 1.49,0.323 0.188,0.167 10 false 25 1.313,0.688 1.5,0.854 0.188,0.167 10 false 24 0.427,3.24 2.063,3.542 1.635,0.302 10 false Main Body ECU (Multiplex Network Body ECU) 0.844,2.781 1.25,2.948 0.406,0.167 10 false CANL 0.833,2.25 1.271,2.417 0.438,0.167 10 false CANH 2.896,2.292 3.271,2.458 0.375,0.167 10 false L133 2.917,2.823 3.281,2.99 0.365,0.167 10 false L133 0.063,3.24 0.542,3.406 0.479,0.167 10 false L201 3.021,2.073 3.208,2.24 0.188,0.167 10 false 5 2.979,2.594 3.167,2.76 0.188,0.167 10 false 11 1.302,2.167 1.49,2.333 0.188,0.167 10 false 14 1.313,2.698 1.5,2.865 0.188,0.167 10 false 13

C356566E02
6.375,5.49 6.792,5.677 0.417,0.188 10 false 120 Ω 5.865,5.635 6.271,5.802 0.406,0.167 10 false CANL 5.438,6.156 5.729,6.323 0.292,0.167 10 false L27 4,5.729 4.323,5.896 0.323,0.167 10 false L132 4,4.625 4.406,4.792 0.406,0.167 10 false L132 4.042,2.427 4.313,2.594 0.271,0.167 10 false L94 4.021,0.417 4.323,0.583 0.302,0.167 10 false L95 4.021,0.948 4.354,1.115 0.333,0.167 10 false L95 5.479,1.365 5.76,1.531 0.281,0.167 10 false L54 4.042,2.958 4.313,3.125 0.271,0.167 10 false L94 2.906,0.417 3.167,0.583 0.26,0.167 10 false L95 2.917,0.948 3.177,1.115 0.26,0.167 10 false L95 4.01,4.167 4.406,4.333 0.396,0.167 10 false L132 4.01,5.208 4.333,5.375 0.323,0.167 10 false L132 2.927,5.198 3.219,5.365 0.292,0.167 10 false A67 2.917,5.719 3.208,5.885 0.292,0.167 10 false A67 5.719,6.156 6.906,6.604 1.188,0.448 10 false Combination Meter Sub-assembly 5.865,5.104 6.302,5.271 0.438,0.167 10 false CANH 0.813,0.948 1.219,1.115 0.406,0.167 10 false CANL 0.771,0.396 1.208,0.563 0.438,0.167 10 false CANH 5.865,0.969 6.271,1.135 0.406,0.167 10 false CANL 5.854,0.406 6.292,0.573 0.438,0.167 10 false CANH 0.802,5.177 1.24,5.344 0.438,0.167 10 false CA1H 0.833,5.729 1.271,5.896 0.438,0.167 10 false CA1L 5.604,5.094 5.813,5.26 0.208,0.167 10 false 19 4.083,4.427 4.292,4.594 0.208,0.167 10 false 11 3,0.75 3.104,0.917 0.104,0.167 10 false 5 2.979,0.219 3.094,0.385 0.115,0.167 10 false 6 1.302,5.094 1.51,5.26 0.208,0.167 10 false 37 1.313,5.625 1.521,5.792 0.208,0.167 10 false 38 4.104,0.76 4.313,0.927 0.208,0.167 10 false 2 4.104,0.208 4.313,0.375 0.208,0.167 10 false 3 4.083,5.531 4.281,5.698 0.198,0.167 10 false 12 5.604,5.615 5.802,5.781 0.198,0.167 10 false 20 4.135,3.969 4.25,4.135 0.115,0.167 10 false 5 4.115,2.219 4.229,2.385 0.115,0.167 10 false 1 4.115,2.76 4.229,2.927 0.115,0.167 10 false 2 4.125,5.01 4.24,5.177 0.115,0.167 10 false 6 3,5 3.115,5.167 0.115,0.167 10 false 1 1.323,0.844 1.615,1.01 0.292,0.167 10 false 12 1.302,0.302 1.552,0.469 0.25,0.167 10 false 11 5.656,0.833 5.771,1 0.115,0.167 10 false 7 5.656,0.302 5.771,0.469 0.115,0.167 10 false 1 3.021,5.521 3.208,5.688 0.188,0.167 10 false 7 0.031,6.135 0.354,6.354 0.323,0.219 10 false A58 0.313,6.135 2.542,6.688 2.229,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 2.708,6.073 4.698,6.573 1.99,0.5 10 false No. 1 CAN Junction Connector 2.708,3.604 4.698,3.792 1.99,0.188 10 false No. 2 CAN Junction Connector 0.052,1.365 0.344,1.521 0.292,0.156 10 false L17 0.375,1.365 1.948,1.927 1.573,0.563 10 false Air Conditioning Amplifier Assembly 5.792,1.365 7.083,1.708 1.292,0.344 10 false Power Steering ECU Assembly 0.802,2.958 1.208,3.125 0.406,0.167 10 false CANL 0.802,2.417 1.24,2.583 0.438,0.167 10 false CANH 2.917,2.438 3.198,2.604 0.281,0.167 10 false L94 2.917,2.958 3.198,3.125 0.281,0.167 10 false L94 1.313,2.313 1.427,2.479 0.115,0.167 10 false 4 2.969,2.76 3.156,2.927 0.188,0.167 10 false 11 2.948,2.229 3.135,2.396 0.188,0.167 10 false 10 1.344,2.844 1.469,3.01 0.125,0.167 10 false 3 0.042,3.385 0.333,3.563 0.292,0.177 10 false L51 0.365,3.385 1.906,4.063 1.542,0.677 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L94 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder left side).


c.
U191024E03
2.781,4.229 2.688,4.229 2.688,4.229 2.448,4.083 false 0.75,0.927 0.99,0.927 0.99,0.927 1.552,1.208 false 0.75,1.208 0.99,1.208 0.99,1.208 1.542,1.417 false 0.729,2.24 1.156,2.24 1.156,2.24 1.563,1.854 false 0.719,1.885 1.146,1.885 1.146,1.885 1.542,1.667 false 2.615,2.188 2.104,2.188 2.104,2.188 1.719,1.854 false 2.604,1.875 2.094,1.875 2.094,1.875 1.75,1.646 false 2.646,0.938 2.125,0.938 2.125,0.938 1.729,1.219 false 2.656,1.188 2.427,1.188 2.427,1.188 1.74,1.406 false 0.063,0.031 0.406,0.198 0.344,0.167 10 false *a 0.042,2.979 0.198,3.156 0.156,0.177 10 false *1 0.167,0.833 0.708,1.01 0.542,0.177 10 false CANH*b 0.156,1.802 0.698,1.979 0.542,0.177 10 false CANH*d 0.156,2.156 0.698,2.333 0.542,0.177 10 false CANH*e 0.177,1.125 0.719,1.302 0.542,0.177 10 false CANH*c 2.698,0.854 3.24,1.031 0.542,0.177 10 false CANL*b 2.656,1.781 3.198,1.958 0.542,0.177 10 false CANL*d 2.646,2.083 3.188,2.26 0.542,0.177 10 false CANL*e 2.698,1.115 3.24,1.292 0.542,0.177 10 false CANL*c 1.604,0.167 2.021,0.365 0.417,0.198 10 false L94 0.25,3.667 0.563,3.844 0.313,0.177 10 false L61 2.802,4.156 3.094,4.333 0.292,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to No. 3 CAN Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 1 CAN junction connector
L94-2 (CANL) - L61-16 (BAT)
L94-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 3 CAN junction connector
L94-5 (CANL) - L61-16 (BAT)
L94-7 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)
L94-8 (CANL) - L61-16 (BAT)
L94-10 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly (steering angle sensor)
L94-11 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (Line to No. 1 CAN junction connector) B
NG (Line to No. 3 CAN junction connector) C
NG (Line to ECU or sensor) D




A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the L95 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder right side).


b.
U191031E02
2.781,4.25 2.688,4.25 2.688,4.25 2.448,4.104 true 0.75,0.938 0.99,0.938 0.99,0.938 1.708,1.219 true 0.75,1.198 0.99,1.198 0.99,1.198 1.698,1.406 true 0.729,2.229 1.156,2.229 1.156,2.229 1.719,1.844 true 0.729,1.885 1.156,1.885 1.156,1.885 1.708,1.667 true 2.615,2.188 2.104,2.188 2.104,2.188 1.875,1.854 true 2.604,1.875 2.094,1.875 2.094,1.875 1.896,1.646 true 2.625,0.948 2.135,0.948 2.135,0.948 1.896,1.229 true 2.625,1.219 2.427,1.219 2.427,1.219 1.896,1.438 true 0.125,0.083 0.469,0.25 0.344,0.167 10 false *a 0.073,2.979 0.229,3.156 0.156,0.177 10 false *1 2.677,0.854 3.219,1.031 0.542,0.177 10 false CANH*b 2.677,1.792 3.219,1.969 0.542,0.177 10 false CANH*d 2.677,2.104 3.219,2.281 0.542,0.177 10 false CANH*e 2.677,1.135 3.219,1.313 0.542,0.177 10 false CANH*c 0.208,0.844 0.75,1.021 0.542,0.177 10 false CANL*b 0.208,1.792 0.75,1.969 0.542,0.177 10 false CANL*d 0.208,2.135 0.75,2.313 0.542,0.177 10 false CANL*e 0.219,1.115 0.76,1.292 0.542,0.177 10 false CANL*c 1.604,0.177 2.021,0.375 0.417,0.198 10 false L95 0.229,3.667 0.542,3.844 0.313,0.177 10 false L61 2.823,4.167 3.115,4.344 0.292,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly
*d to Airbag ECU Assembly
*e to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power steering ECU assembly
L95-2 (CANL) - L61-16 (BAT)
L95-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Air conditioning amplifier assembly
L95-5 (CANL) - L61-16 (BAT)
L95-9 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Airbag ECU assembly
L95-8 (CANL) - L61-16 (BAT)
L95-12 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
L95-11 (CANL) - L61-16 (BAT)




OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.
U154822E03
2.427,4.073 2.688,4.25 2.688,4.25 2.865,4.25 false 2.031,1.479 2.031,0.667 2.031,0.667 1.833,0.667 false 2,1.813 2,2.396 2,2.396 1.74,2.396 false 2.177,1.49 2.177,0.667 2.177,0.667 2.375,0.667 false 2.167,1.802 2.167,2.396 2.167,2.396 2.427,2.396 false 0.115,2.729 0.365,2.969 0.25,0.24 10 false *1 0.115,0.115 0.365,0.354 0.25,0.24 10 false *a 1.188,0.573 1.875,0.823 0.688,0.25 10 false CANH*b 1.156,2.302 1.844,2.552 0.688,0.25 10 false CANL*b 2.438,0.583 3.125,0.833 0.688,0.25 10 false CANH*c 2.49,2.302 3.177,2.552 0.688,0.25 10 false CANL*c 2.917,4.156 3.271,4.354 0.354,0.198 10 false BAT 0.229,3.75 0.646,4 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L132

Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Combination Meter Sub-assembly

Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 2 CAN junction connector
L132-11 (CANL) - L61-16 (BAT)
L132-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter sub-assembly
L132-12 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to combination meter sub-assembly) C




A

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.
U191047E02
2.438,4.125 2.698,4.302 2.698,4.302 2.875,4.302 false 1.292,1.469 1.292,0.656 1.292,0.656 1.094,0.656 false 1.292,1.844 1.292,2.469 1.292,2.469 1.031,2.469 false 0.094,2.885 0.344,3.125 0.25,0.24 10 false *1 0.083,0.083 0.333,0.323 0.25,0.24 10 false *a 0.563,0.573 1.25,0.823 0.688,0.25 10 false CANH*b 0.521,2.385 1.208,2.635 0.688,0.25 10 false CANL*b 2.917,4.208 3.271,4.406 0.354,0.198 10 false BAT 0.219,3.771 0.635,4.021 0.417,0.25 10 false L61 0.385,1.49 0.802,1.74 0.417,0.25 10 false A67

Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Tester Connection Condition Specified Condition
A67-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A67-7 (CANL) - L61-16 (BAT)




OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.
U191051E02
2.438,4.115 2.698,4.292 2.698,4.292 2.875,4.292 false 1.813,1.49 1.813,0.677 1.813,0.677 1.615,0.677 false 1.823,1.823 1.823,2.448 1.823,2.448 1.563,2.448 false 2.177,1.479 2.177,0.656 2.177,0.656 2.385,0.656 false 2.177,1.833 2.177,2.458 2.177,2.458 2.438,2.458 false 1.99,1.479 1.99,0.333 1.99,0.333 1.698,0.333 false 2,1.823 2,2.76 2,2.76 1.771,2.76 false 0.146,2.875 0.396,3.115 0.25,0.24 10 false *1 0.135,0.188 0.385,0.427 0.25,0.24 10 false *a 1.073,0.594 1.76,0.844 0.688,0.25 10 false CANH*b 1.042,2.365 1.729,2.615 0.688,0.25 10 false CANL*b 2.917,4.198 3.271,4.396 0.354,0.198 10 false BAT 0.177,3.76 0.594,4.01 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L133 2.438,0.573 3.042,0.823 0.604,0.25 10 false CANH*d 2.49,2.375 3.073,2.625 0.583,0.25 10 false CANL*d 1.177,0.25 1.74,0.5 0.563,0.25 10 false CANH*c 1.26,2.677 1.813,2.927 0.552,0.25 10 false CANL*c

Disconnect the L133 wire harness connector from the No. 3 CAN junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Main Body ECU (Multiplex Network Body ECU)
*d to No. 2 CAN Junction Connector

Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control ECU
L133-10 (CANL) - L61-16 (BAT)
L133-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
L133-11 (CANL) - L61-16 (BAT)
L133-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 2 CAN junction connector
L133-12 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to ECU or sensor) C




A

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.
U191048E02
2.427,4.104 2.688,4.281 2.688,4.281 2.865,4.281 false 1.281,1.479 1.281,0.667 1.281,0.667 1.083,0.667 false 1.292,1.833 1.292,2.458 1.292,2.458 1.031,2.458 false 1.479,1.458 1.479,0.646 1.479,0.646 1.677,0.646 false 1.469,1.833 1.469,2.458 1.469,2.458 1.729,2.458 false 0.094,2.906 0.344,3.146 0.25,0.24 10 false *1 0.042,0.208 0.292,0.448 0.25,0.24 10 false *a 0.552,0.594 1.24,0.844 0.688,0.25 10 false CANH*b 0.521,2.375 1.208,2.625 0.688,0.25 10 false CANL*b 2.917,4.198 3.271,4.396 0.354,0.198 10 false BAT 0.208,3.771 0.625,4.021 0.417,0.25 10 false L61 0.375,1.49 0.792,1.74 0.417,0.25 10 false A68 1.729,0.563 2.417,0.813 0.688,0.25 10 false CANH*c 1.771,2.375 2.458,2.625 0.688,0.25 10 false CANL*c

Disconnect the A68 wire harness connector from the No. 3 CAN junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to ECM
*c to Transmission Control ECU Assembly

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A68-7 (CANL) - L61-16 (BAT)
A68-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Transmission control ECU assembly
A68-8 (CANL) - L61-16 (BAT)




OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).



c.

Measure the resistance according to the value(s) in the table below.

U191199E03
1.948,1.438 1.948,0.719 1.948,0.719 2.281,0.719 false 1.854,1.417 1.854,0.698 1.854,0.698 1.49,0.698 false 5.948,1.708 5.948,2.167 5.948,2.167 5.719,2.167 false 0.115,0.052 0.49,0.333 0.375,0.281 10 false *a 2.344,0.635 3.177,0.948 0.833,0.313 10 false CA4L 1.083,0.615 1.917,0.927 0.833,0.313 10 false CA4H 5.406,2.083 6.24,2.396 0.833,0.313 10 false BAT 1.729,0.104 2.26,0.323 0.531,0.219 10 false L192 3.76,0.083 4.135,0.365 0.375,0.281 10 false *1 5.25,0.125 5.781,0.365 0.531,0.24 10 false L61

Text in Illustration
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -

Standard Resistance:
Tester Connection Condition Specified Condition
L192-18 (CA4H) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-17 (CA4L) - L61-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR