Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301762 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 69060A 2.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock with motor assembly.



a.

w/o Double Locking System:

i.
B282573

Install the rear door inside locking cable assembly to the rear door lock with motor assembly as shown in the illustration.


ii.
B282574

Engage the 3 claws as shown in the illustration.


iii.
B282575

Install the rear door lock remote control cable assembly to the rear door lock with motor assembly as shown in the illustration.


iv.
B282576

Engage the claw as shown in the illustration.



b.

w/ Double Locking System:

i.
B310475

Install the rear door inside locking cable assembly to the rear door lock with motor assembly as shown in the illustration.


ii.
B310473

Engage the 3 claws as shown in the illustration.


iii.
B310471

Install the rear door lock remote control cable assembly to the rear door lock with motor assembly as shown in the illustration.


iv.
B310469

Engage the claw as shown in the illustration.



c.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


d.

When reusing the rear door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



e.
B282577E01
0.247,2.531 0.465,2.727 0.218,0.196 10 *1 0.449,2.614 1.374,2.472 false

Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.

Text in Illustration
*1 Release Plate

HINT:

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.



f.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68104 3.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67488C 4.INSTALL REAR DOOR REAR GUIDE SEAL

Hide 67872 5.CONNECT REAR DOOR WEATHERSTRIP

a.

Connect the rear door weatherstrip.


Hide 67408D 6.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

Hide 68152C 7.INSTALL REAR DOOR GLASS RUN

Hide 67842E 8.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 67628 9.INSTALL REAR DOOR TRIM BRACKET

Hide 67604 10.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74262 11.INSTALL REAR DOOR ARMREST COVER

Hide 12.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 69284D 13.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 20.INITIALIZE POWER WINDOW CONTROL SYSTEM