Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061950 DOOR / HATCH _0301880 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 75762A 7.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75740 8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67674A 9.INSTALL REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)

a.
B282953

Engage the clip to install a new rear door frame garnish.


Hide 67676C 10.INSTALL REAR DOOR NO. 2 FRAME GARNISH (w/o Rear Door Sunshade)

a.
B314486

Engage the clip to install a new rear door No. 2 frame garnish.


Hide 67674A 11.INSTALL REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)

a.
B314404

Engage the clip to install a new rear door frame garnish.


Hide 67676C 12.INSTALL REAR DOOR NO. 2 FRAME GARNISH (w/ Rear Door Sunshade)

a.
B314405

Engage the clip to install a new rear door No. 2 frame garnish.


Hide 67003C 13.INSTALL REAR DOOR PANEL CUSHION

a.
B282977

Engage the 2 claws to install 2 new rear door panel cushions.


Hide 69204A 14.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B282978E01
0.121,0.088 0.299,0.246 0.177,0.158 10 *a 0.121,2.266 0.299,2.424 0.177,0.158 10 *b

Engage the door handle nut and claw.

Text in Illustration
*a Outside
*b Inside


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 15.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B282975

Engage the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 16.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B282974

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69240 17.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B282979

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B282980

Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


Hide 69227L 18.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B282970

Engage the claw and install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 19.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B282981

Install the rear door inside locking cable assembly as shown in the illustration.


b.
B282982

Engage the 3 claws as shown in the illustration.


Hide 69780B 20.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B310475

Install the rear door inside locking cable assembly as shown in the illustration.


b.
B310473

Engage the 3 claws as shown in the illustration.


Hide 69740D 21.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B282983

Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B282984

Engage the claw as shown in the illustration.


Hide 69740D 22.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B310471

Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B310469

Engage the claw as shown in the illustration.


Hide 69060A 23.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.
B282965

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B282577E01
0.247,2.531 0.465,2.727 0.218,0.196 10 *1 0.449,2.614 1.374,2.472 false

Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.

Text in Illustration
*1 Release Plate


d.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.


e.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 85720E 24.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


a.
B282963

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 25.INSTALL REAR DOOR POWER WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door power window regulator assembly.


b.

Install the temporary bolt to the rear door power window regulator assembly.


c.
B282962E01
1.663,1.095 1.816,1.248 0.153,0.152 10 *1 1.843,1.198 2.189,1.299 false

Temporarily install rear door power window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68104 26.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the rear power window regulator motor connector and power window regulator switch assembly, and move the rear door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the power window regulator switch assembly and rear power window regulator motor connector.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


e.
B282986

Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.


f.

Install the rear door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67488C 27.INSTALL REAR DOOR REAR GUIDE SEAL

a.

Install the rear door rear guide seal as shown in the illustration.

B282987


b.

Install the 3 screws.


Hide 67408D 28.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

a.
B282959

Install the rear door window guide sub-assembly with the screw and bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68152C 29.INSTALL REAR DOOR GLASS RUN

a.
B282958

Install the rear door glass run.


Hide 67872 30.INSTALL REAR DOOR WEATHERSTRIP

a.
B282957

Engage the 20 clips and install the rear door weatherstrip.


Hide 68640A 31.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the rear door check assembly.


b.

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
B282956

Install the rear door check assembly with the bolt and 2 nuts.

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 67842E 32.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.


c.
B282988E01
0.155,0.149 0.324,0.312 0.169,0.163 10 *1 2.22,0.141 2.389,0.304 0.169,0.163 10 *1 0.46,2.93 0.630,3.093 0.169,0.163 10 *1

Attach the rear door service hole cover according to the reference points on the rear door panel.

Text in Illustration
*1 Reference Point

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



d.

Connect the 2 connectors.


Hide 67628 33.INSTALL REAR DOOR TRIM BRACKET

a.
B282954

Install the rear door trim bracket with the 2 screws.


Hide 86160Y 35.INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)

Hide 69206C 36.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B282951

Engage the 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 65908D 37.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B310467

Install the rear curtain sub-assembly with the 9 screws.


Hide 68174A 38.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B282989

Engage the 7 claws to install the rear door inner glass weatherstrip to the rear door trim board sub-assembly as shown in the illustration.


Hide 67604 39.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B282990E01
2.579,1.014 2.751,1.165 0.172,0.151 10 *1 2.16,1.332 2.556,1.111 false 1.932,1.988 2.104,2.139 0.172,0.151 10 *2 2.018,1.812 2.016,1.979 false

Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly.

Text in Illustration
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


b.

for 8 Speakers:

i.

Connect the connector.



c.
B282991

Engage the 9 clips and install the rear door trim board sub-assembly.


d.

Install the 2 screws.


e.

If protective tape has been applied, remove it.


Hide 74262 40.INSTALL REAR DOOR ARMREST COVER

a.
B282947

Install the rear door armrest cover.


Hide 41.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B282992

Engage the 5 guides, 10 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 69284D 42.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B282993

Engage the 3 claws to install the rear door inside handle bezel plug.


Hide 43.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 49.INITIALIZE POWER WINDOW CONTROL SYSTEM