Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when there is a problem in the ACC output circuit. The ACC circuit is the circuit that goes from inside the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the certification ECU (smart key ECU assembly) and the ACC relay is detected.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274 Malfunction in the ACC relay activation circuit in the certification ECU (smart key ECU assembly) or the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

ECU-B2 fuse

·

ACC relay (Instrument panel junction block assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.
HINT:

To turn the power switch on (ACC), carry the key and press the power switch with park (P) selected and the brake pedal released.



*: Only output while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off.

·

If there is a malfunction when the relay is off, the ACC relay does not turn on even though the power source mode is on (ACC).


HINT:

The power source can change to on (IG) and the hybrid control system can be started.


-

WIRING DIAGRAM

B327840E22
0.073,1.094 0.958,1.615 0.885,0.521 10 false from Auxiliary Battery 1.531,1.26 2.448,1.458 0.917,0.198 10 false ECU-B2 2.375,1.104 3.292,1.302 0.917,0.198 10 false L195 2.49,0.927 3.406,1.125 0.917,0.198 10 false 2 2.719,1.094 3.635,1.292 0.917,0.198 10 false +B 2.375,2.25 3.292,2.448 0.917,0.198 10 false L195 2.448,2.083 3.365,2.281 0.917,0.198 10 false 11 2.729,2.25 3.646,2.448 0.917,0.198 10 false E 2.375,2.896 3.917,3.302 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly) 3.094,1.75 4.01,1.948 0.917,0.198 10 false ACCD 3.552,1.75 4.469,1.948 0.917,0.198 10 false 197 3.646,1.583 3.938,1.771 0.292,0.188 10 false 4 4.281,1.333 5.198,1.531 0.917,0.198 10 false 2E 4.281,1.75 5.198,1.948 0.917,0.198 10 false 2A 4.292,1.573 5.208,1.771 0.917,0.198 10 false 43 4.323,1.156 5.24,1.354 0.917,0.198 10 false 1 5.49,2.083 6.406,2.281 0.917,0.198 10 false ACC 6.417,1.75 6.833,2 0.417,0.25 10 false 2B 6.417,1.333 6.833,1.583 0.417,0.25 10 false 2B 6.438,1.156 6.854,1.406 0.417,0.25 10 false 34 5.99,1.479 6.375,1.865 0.385,0.385 10 false ECU-ACC 4.125,2.438 6.865,2.646 2.74,0.208 10 false Instrument Panel Junction Block Assembly 6.469,1.573 6.885,1.823 0.417,0.25 10 false 6 0.302,0.115 1.448,0.469 1.146,0.354 12 false for LHD:

B327840E24
0.073,1.094 0.958,1.615 0.885,0.521 10 false from Auxiliary Battery 1.531,1.26 2.448,1.458 0.917,0.198 10 false ECU-B2 2.375,1.104 3.292,1.302 0.917,0.198 10 false L195 2.49,0.927 3.406,1.125 0.917,0.198 10 false 2 2.719,1.094 3.635,1.292 0.917,0.198 10 false +B 2.375,2.25 3.292,2.448 0.917,0.198 10 false L195 2.448,2.083 3.365,2.281 0.917,0.198 10 false 11 2.729,2.25 3.646,2.448 0.917,0.198 10 false E 2.375,2.896 3.917,3.302 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly) 3.094,1.75 4.01,1.948 0.917,0.198 10 false ACCD 3.552,1.75 4.469,1.948 0.917,0.198 10 false 197 3.646,1.583 3.938,1.771 0.292,0.188 10 false 4 4.281,1.333 5.198,1.531 0.917,0.198 10 false 2F 4.281,1.75 5.198,1.948 0.917,0.198 10 false 2A 4.292,1.573 5.208,1.771 0.917,0.198 10 false 43 4.323,1.156 5.24,1.354 0.917,0.198 10 false 1 5.49,2.083 6.406,2.281 0.917,0.198 10 false ACC 6.417,1.75 6.833,2 0.417,0.25 10 false 2B 6.417,1.333 6.833,1.583 0.417,0.25 10 false 2B 6.438,1.156 6.854,1.406 0.417,0.25 10 false 34 5.99,1.479 6.375,1.865 0.385,0.385 10 false ECU-ACC 4.125,2.438 6.865,2.646 2.74,0.208 10 false Instrument Panel Junction Block Assembly 6.469,1.573 6.885,1.823 0.417,0.25 10 false 6 0.302,0.115 1.448,0.469 1.146,0.354 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the power source mode cannot change to on (ACC), the audio and navigation systems do not operate.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2A and 2B instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-4 (ACCD) - 2A-25 Always Below 1 Ω
2B-9 - Body ground Always Below 1 Ω
L197-4 (ACCD) or 2A-25 - Body ground Always 10 kΩ or higher




OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ACC RELAY)
a.

Remove the instrument panel junction block assembly.

U190981E02
1.385,0.208 1.698,0.406 0.313,0.198 10 false 2B 5.323,0.208 5.635,0.406 0.313,0.198 10 false 2A 2.865,1.823 3.177,2.021 0.313,0.198 10 false 2E 2.885,2.26 3.198,2.458 0.313,0.198 10 false 2F 3.177,1.813 3.49,2.01 0.313,0.198 10 false *A 3.167,2.26 3.479,2.458 0.313,0.198 10 false *B

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly


c.

Measure the resistance according to the value(s) the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2B-13*1
2F-1 - 2B-13*2
Auxiliary battery voltage not applied between terminals 2A-25 and 2B-9 10 kΩ or higher
Auxiliary battery voltage applied between terminals 2A-25 and 2B-9 Below 1 Ω


·

*1: for LHD

·

*2: for RHD




OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
U190843E02
1.156,1.083 0.875,1.813 true 0.156,0.104 0.344,0.26 0.188,0.156 10 false *a 1.458,0.323 1.854,0.479 0.396,0.156 10 false L197 0.573,1.844 1,1.99 0.427,0.146 10 false ACCD

Reconnect the L197 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L197-4 (ACCD) - Body ground Power switch off → Power switch on (ACC)) 1 V or less → 8.5 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)