When the key is in the vehicle and the power switch is pressed, the power management control ECU receives a signal and changes the power source mode.
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).
When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.
When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.
for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
IG1 Relay Monitor(Outside) ·
IG2 Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor ·
Key Certif Wait T-Out |
- |
OK
NG
OK
NG
Reconnect the L5 and L6 connectors to the power management control ECU.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Key Certif Wait T-Out | Key verification malfunction/No or Yes | No: Verification normal
Yes: Verification error (detected when ID code from key and ID stored in certification ECU (smart key ECU assembly) do not match) |
The hybrid control system can be started, even if this item displays "Yes". |
When more than 1 second elapses after the power switch is turned from off to on (IG), No is displayed in the Data List.
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Switch1 | Condition of power switch contact 1/OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the power switch input signal is malfunctioning. |
| Start Switch2 | Condition of power switch contact 2/OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
This is the backup for power switch 1. ·
Behaves the same way as power switch 1. |
ON (power switch is pushed) and OFF (power switch is not pushed) appear on the screen.
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | State of power supply/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON | All OFF: Power switch off (power supply off)
ACC ON: Power switch on (ACC) (ACC relay on) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Starting hybrid control system |
Since "IG1 ON" and "IG2 ON" turn "on" at approximately the same time, "IG1 ON" may not be displayed ("IG1 ON" turns on for a very short time). |
Measure the voltage while checking the Data List on the GTS.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-2 (IG1D) - Body ground | Power switch off | Below 1 V |
| L6-2 (IG1D) - Body ground | Power switch on (ACC) | Below 1 V |
| L6-2 (IG1D) - Body ground | Power switch on (IG) | 9 V or higher |
| A22-2 (IG2D) - Body ground | Power switch off | Below 1 V |
| A22-2 (IG2D) - Body ground | Power switch on (ACC) | Below 1 V |
| A22-2 (IG2D) - Body ground | Power switch on (IG) | 9 V or higher |
| L6-1 (ACCD) - Body ground | Power switch off | Below 1 V |
| L6-1 (ACCD) - Body ground | Power switch on (IG) | 9 V or higher |
| L6-1 (ACCD) - Body ground | Power switch on (ACC) | 9 V or higher |
OK
NG
Check that the power source mode becomes on (ACC) and on (IG) when the power switch is operated.
Power source mode becomes on (ACC) and on (IG) when the power switch is operated.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Remove the power switch (See page Engine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L43-7 (SS1) - L43-5 (GND) | Pushed | Below 1 Ω |
| L43-7 (SS1) - L43-5 (GND) | Not pushed | 10 kΩ or higher |
| L43-2 (SS2) - L43-5 (GND) | Pushed | Below 1 Ω |
| L43-2 (SS2) - L43-5 (GND) | Not pushed | 10 kΩ or higher |
| *a | Component without harness connected
(Power Switch) |
OK
NG
Disconnect the L5 and L6 connectors from the power management control ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-17 (SSW2) - L43-2 (SS2) | Always | Below 1 Ω |
| L5-7 (SSW1) - L43-7 (SS1) | Always | Below 1 Ω |
| L6-17 (SSW2) - Body ground | Always | 10 kΩ or higher |
| L5-7 (SSW1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Enter the following menus:
for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.
for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The following DTCs are not output:
·
B2785 ·
B2287 ·
B2784 |
A |
| DTC B2785 is not output but DTC B2287 is output. | B |
| DTCs other than B2287 are output. | C |
A
B
C