Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.08–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the key is in the vehicle and the power switch is pressed, the power management control ECU receives a signal and changes the power source mode.

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



WIRING DIAGRAM

B292512E05
2.469,7.781 3.875,8.146 1.406,0.365 10 false Power Management Control ECU 2.438,7.302 2.708,7.448 0.271,0.146 10 false L6 2.458,6.896 2.729,7.042 0.271,0.146 10 false L5 2.5,6.698 2.604,6.844 0.104,0.146 10 false 6 2.479,7.104 2.583,7.25 0.104,0.146 10 false 4 2.5,5.76 2.604,5.906 0.104,0.146 10 false 5 2.49,6.156 2.594,6.302 0.104,0.146 10 false 5 2.74,7.302 3.042,7.448 0.302,0.146 10 false E12 2.74,6.906 3.021,7.052 0.281,0.146 10 false E1 2.448,6.344 2.719,6.49 0.271,0.146 10 false L6 2.458,5.938 2.729,6.083 0.271,0.146 10 false L5 2.49,3.917 2.594,4.063 0.104,0.146 10 false 7 1.917,4.021 2.021,4.167 0.104,0.146 10 false 7 1.917,4.406 2.021,4.552 0.104,0.146 10 false 2 0.615,4.417 0.719,4.563 0.104,0.146 10 false 5 2.448,4.333 2.635,4.479 0.188,0.146 10 false 17 2.448,4.51 2.719,4.656 0.271,0.146 10 false L6 2.458,4.125 2.729,4.271 0.271,0.146 10 false L5 2.729,4.521 3.177,4.667 0.448,0.146 10 false SSW2 2.729,4.125 3.177,4.271 0.448,0.146 10 false SSW1 1.49,4.521 1.802,4.667 0.313,0.146 10 false SS2 0.813,4.563 1.177,4.708 0.365,0.146 10 false GND 0.833,4.854 1.125,5.01 0.292,0.156 10 false L43 0.833,5.01 1.781,5.167 0.948,0.156 10 false Power Switch 1.5,4.125 1.813,4.271 0.313,0.146 10 false SS1 2.479,1.635 2.583,1.781 0.104,0.146 10 false 2 2.385,1.833 2.708,2 0.323,0.167 10 false A22 3.802,2.406 3.906,2.552 0.104,0.146 10 false 2 3.76,2.594 4.042,2.74 0.281,0.146 10 false L6 4.417,2.406 4.615,2.552 0.198,0.146 10 false 25 2.031,1.75 2.229,1.896 0.198,0.146 10 false 2 0.552,1.75 0.75,1.896 0.198,0.146 10 false 3 0.531,2.49 0.75,2.635 0.219,0.146 10 false 1A 4.417,4.542 4.615,4.688 0.198,0.146 10 false 43 4.406,4.74 4.646,4.896 0.24,0.156 10 false 2A 5.979,3.458 6.083,3.604 0.104,0.146 10 false 4 5.927,3.656 6.146,3.802 0.219,0.146 10 false 2B 5.969,4.542 6.073,4.688 0.104,0.146 10 false 6 5.927,4.75 6.146,4.896 0.219,0.146 10 false 2B 4.948,1.823 5.625,1.969 0.677,0.146 10 false IG1 No. 1 4.948,2.854 5.625,3 0.677,0.146 10 false IG1 No. 2 4.958,3.927 5.635,4.094 0.677,0.167 10 false IG1 No. 3 5.125,5.01 5.552,5.156 0.427,0.146 10 false ACC 5,6.083 5.646,6.281 0.646,0.198 10 false P/POINT 4.396,6.583 6.188,7 1.792,0.417 10 false Instrument Panel Junction Block Assembly 2.729,1.792 3.104,1.938 0.375,0.146 10 false IG2D 3.26,2.604 3.635,2.75 0.375,0.146 10 false IG1D 2.469,0.854 2.573,1 0.104,0.146 10 false 1 2.438,1.042 2.719,1.188 0.281,0.146 10 false L5 2.729,1.042 3.177,1.188 0.448,0.146 10 false AM22 2.479,0.448 2.583,0.594 0.104,0.146 10 false 7 2.427,0.646 2.708,0.792 0.281,0.146 10 false L6 1.344,0.781 1.677,0.927 0.333,0.146 10 false AM2 1.198,2.104 1.5,2.271 0.302,0.167 10 false IG2 0.094,0.646 0.969,1.052 0.875,0.406 10 false from Auxiliary Battery 0.531,2.646 2.385,3.25 1.854,0.604 10 false No. 2 Integration Relay (Engine Room Relay Block and Junction Block Assembly) 2.729,0.646 3.177,0.792 0.448,0.146 10 false AM21 3.771,4.74 4.042,4.885 0.271,0.146 10 false L6 3.813,4.542 3.917,4.688 0.104,0.146 10 false 1 2.74,6.354 3.031,6.5 0.292,0.146 10 false E02 2.75,5.958 3.042,6.104 0.292,0.146 10 false E01 3.188,4.75 3.635,4.896 0.448,0.146 10 false ACCD 4.396,2.594 4.615,2.74 0.219,0.146 10 false 2B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor

·

Key Certif Wait T-Out


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.READ VALUE USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING GTS
a.

Reconnect the L5 and L6 connectors to the power management control ECU.


b.

Turn the power switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Power Source Control / Data List.


g.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Certif Wait T-Out Key verification malfunction/No or Yes No: Verification normal
Yes: Verification error (detected when ID code from key and ID stored in certification ECU (smart key ECU assembly) do not match)
The hybrid control system can be started, even if this item displays "Yes".

OK:

When more than 1 second elapses after the power switch is turned from off to on (IG), No is displayed in the Data List.




OK

4.READ VALUE USING GTS

NG

9.CHECK FOR DTC
4.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch1 Condition of power switch contact 1/OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the power switch input signal is malfunctioning.


Start Switch2 Condition of power switch contact 2/OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

This is the backup for power switch 1.

·

Behaves the same way as power switch 1.



OK:

ON (power switch is pushed) and OFF (power switch is not pushed) appear on the screen.




OK

5.CHECK POWER MANAGEMENT CONTROL ECU

NG

7.CHECK POWER SWITCH
5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition State of power supply/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON All OFF: Power switch off (power supply off)
ACC ON: Power switch on (ACC) (ACC relay on)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Starting hybrid control system
Since "IG1 ON" and "IG2 ON" turn "on" at approximately the same time, "IG1 ON" may not be displayed ("IG1 ON" turns on for a very short time).


b.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-2 (IG1D) - Body ground Power switch off Below 1 V
L6-2 (IG1D) - Body ground Power switch on (ACC) Below 1 V
L6-2 (IG1D) - Body ground Power switch on (IG) 9 V or higher
A22-2 (IG2D) - Body ground Power switch off Below 1 V
A22-2 (IG2D) - Body ground Power switch on (ACC) Below 1 V
A22-2 (IG2D) - Body ground Power switch on (IG) 9 V or higher
L6-1 (ACCD) - Body ground Power switch off Below 1 V
L6-1 (ACCD) - Body ground Power switch on (IG) 9 V or higher
L6-1 (ACCD) - Body ground Power switch on (ACC) 9 V or higher




OK

6.CONFIRMATION TEST

NG

6.CONFIRMATION TEST
a.

Check that the power source mode becomes on (ACC) and on (IG) when the power switch is operated.

OK:

Power source mode becomes on (ACC) and on (IG) when the power switch is operated.




OK

NG

CHECK RELAY CONTACT SIDE CIRCUIT

7.CHECK POWER SWITCH
a.
U154697E03
0.677,1.438 0.781,1.438 0.781,1.438 1.521,2.115 true 0.677,1.719 0.781,1.719 0.781,1.719 1.177,2.104 false 2.729,1.75 2.625,1.75 2.625,1.75 2.073,2.135 true 0.198,0.302 2.729,0.667 2.531,0.365 10 false *a 0.354,1.354 0.729,1.552 0.375,0.198 10 false GND 0.365,1.635 0.708,1.833 0.344,0.198 10 false SS1 2.781,1.677 3.125,1.875 0.344,0.198 10 false SS2 0.292,2.177 0.594,2.375 0.302,0.198 10 false L43

Remove the power switch (See page Engine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L43-7 (SS1) - L43-5 (GND) Pushed Below 1 Ω
L43-7 (SS1) - L43-5 (GND) Not pushed 10 kΩ or higher
L43-2 (SS2) - L43-5 (GND) Pushed Below 1 Ω
L43-2 (SS2) - L43-5 (GND) Not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Power Switch)



OK

8.CHECK HARNESS AND CONNECTOR (POWER SWITCH - POWER MANAGEMENT CONTROL ECU AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (POWER SWITCH - POWER MANAGEMENT CONTROL ECU AND BODY GROUND)
a.

Disconnect the L5 and L6 connectors from the power management control ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-17 (SSW2) - L43-2 (SS2) Always Below 1 Ω
L5-7 (SSW1) - L43-7 (SS1) Always Below 1 Ω
L6-17 (SSW2) - Body ground Always 10 kΩ or higher
L5-7 (SSW1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FOR DTC
a.

Enter the following menus:

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Result:
Result Proceed to
The following DTCs are not output:
·

B2785

·

B2287

·

B2784


A
DTC B2785 is not output but DTC B2287 is output. B
DTCs other than B2287 are output. C




A

B

GO TO OTHER FLOW CHART (DTC B2287)

C

GO TO DIAGNOSTIC TROUBLE CODE CHART