Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Immobiliser System does not Operate Properly  


DESCRIPTION

The engine immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

CAUTION:
·

The engine immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the hybrid vehicle control ECU or ID code box (immobiliser code ECU), refer to Service Bulletin..

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If an engine immobiliser system or SFI system DTC is output, first perform troubleshooting for the engine immobiliser system or SFI system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS

B

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).

OK:

Hybrid control system starts normally.


Result:
Result Proceed to
NG A
OK B




A

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI AND IMO)

B

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

U190939E02
5.385,1.313 5.385,2.271 5.385,2.271 5.531,2.271 false 5.292,1.313 5.292,2.271 5.292,2.271 5.156,2.271 false 5.25,0.229 5.573,0.406 0.323,0.177 10 false L6 1.031,3.604 1.375,3.76 0.344,0.156 10 false GND 0.135,0.094 0.406,0.323 0.271,0.229 10 false *a 2.927,3.719 3.198,3.938 0.271,0.219 10 false *b 3.115,3.719 3.385,3.938 0.271,0.219 10 false *c 3.333,5.729 3.604,5.948 0.271,0.219 10 false *b 3.521,5.729 3.792,5.948 0.271,0.219 10 false *c 1.854,7.094 2.125,7.313 0.271,0.219 10 false *d 1.49,6.479 1.76,6.698 0.271,0.219 10 false *i 3.208,6.49 3.479,6.708 0.271,0.219 10 false *i 2.406,4.646 2.677,4.865 0.271,0.219 10 false *f 3.438,4.646 3.708,4.865 0.271,0.219 10 false *h 3.031,2.615 3.302,2.833 0.271,0.219 10 false *g 1.927,7.344 2.198,7.563 0.271,0.219 10 false *e 3.719,7.094 3.99,7.313 0.271,0.219 10 false *d 3.656,7.354 3.927,7.573 0.271,0.219 10 false *e 1.031,5.646 1.375,5.802 0.344,0.156 10 false GND 4.854,2.198 5.385,2.438 0.531,0.24 10 false IMO 5.573,2.198 5.875,2.354 0.302,0.156 10 false IMI

Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms *f Waveform 1
*g Waveform 2 *h Waveform 3
*i Waveform 1 (detail) - -

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
L6-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
L6-22 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)


Result:
Result Proceed to
Normal waveform A
Waveform 1 not output, or has abnormal wavelength or shape B
Waveform 2 not output, or has abnormal wavelength or shape C
Waveform 3 not output, or has abnormal wavelength or shape D




A

4.REGISTER ECU COMMUNICATION ID

B

6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)

C

D

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the L191 ID code box (immobiliser code ECU) connector.


b.

Disconnect the L6 hybrid control system connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L191-3 (EFII) - L6-23 (IMO) Always Below 1 Ω
L191-3 (EFII) or L6-23 (IMO) - Body ground Always 10 kΩ or higher
L191-4 (EFIO) - L6-22 (IMI) Always Below 1 Ω
L191-4 (EFIO) or L6-22 (IMI) - Body ground Always 10 kΩ or higher




OK

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG