Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (IG) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E249011E05
3.58,2.189 4.263,2.337 0.683,0.147 10 IG1 NO. 1 1.086,1.426 1.592,1.573 0.506,0.147 10 DC/DC 2.206,1.116 2.318,1.263 0.112,0.147 10 1 2.085,1.29 2.414,1.437 0.329,0.147 10 2F*2 2.206,0.463 2.318,0.611 0.112,0.147 10 1 2.085,0.645 2.411,0.793 0.326,0.147 10 2E*1 5.429,1.116 5.612,1.263 0.183,0.147 10 32 5.399,1.298 5.641,1.445 0.242,0.147 10 MB 5.721,1.298 5.913,1.445 0.192,0.147 10 IG 2.206,2.377 2.318,2.524 0.112,0.147 10 6 2.155,2.559 2.368,2.706 0.213,0.147 10 2B 2.206,2.965 2.318,3.113 0.112,0.147 10 4 2.155,3.147 2.368,3.295 0.213,0.147 10 2B 2.576,4.408 3.363,4.556 0.787,0.147 10 *1: for LHD 3.697,4.408 4.484,4.556 0.787,0.147 10 *2: for RHD 2.155,1.928 2.368,2.076 0.213,0.147 10 2B 2.155,1.746 2.339,1.894 0.183,0.147 10 25 4.336,1.426 5.258,1.573 0.922,0.147 10 ECU-IG NO. 1 0.131,2.907 0.994,3.275 0.863,0.368 10 from Auxiliary Battery 2.904,3.552 4.530,3.861 1.626,0.309 10 Instrument Panel Junction Block Assembly 5.267,3.926 6.968,4.234 1.701,0.309 10 Main Body ECU (Multiplex Network Body ECU) 0.458,4.031 2.076,4.363 1.618,0.332 10 from Power Management Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC (ENTRY AND START SYSTEM (for Start Function))
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR)

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Power switch IG signal/ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2E*1 or 2F*2 instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2E-1 - Body ground*1 Power switch off 11 to 14 V
2F-1 - Body ground*2 Power switch off 11 to 14 V



*1: for LHD

*2: for RHD



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U191347E02
5.469,3.021 5.667,3.208 false 0.292,0.25 0.479,0.417 0.188,0.167 10 false *a 5.083,0.719 5.292,0.885 0.208,0.167 10 false 2B 1.302,0.792 1.51,0.958 0.208,0.167 10 false 2E 1.604,0.76 1.813,0.927 0.208,0.167 10 false *A 1.948,0.792 2.156,0.958 0.208,0.167 10 false 2F 2.26,0.76 2.469,0.927 0.208,0.167 10 false *B 3.531,2.51 3.792,2.677 0.26,0.167 10 false MB 5.677,3.219 5.865,3.385 0.188,0.167 10 false IG

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - MB-32 (IG)*1 Always 10 kΩ or higher
2E-1 - MB-32 (IG)*1 Auxiliary battery positive (+) → 2B-25
Auxiliary battery negative (-) → 2B-6, 2B-4
Below 1 Ω
2F-1 - MB-32 (IG)*2 Always 10 kΩ or higher
2F-1 - MB-32 (IG)*2 Auxiliary battery positive (+) → 2B-25
Auxiliary battery negative (-) → 2B-6, 2B-4
Below 1 Ω


*1: for LHD

*2: for RHD




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY