Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (ACC) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E249011E08
3.76,2.188 4.448,2.333 0.688,0.146 10 false ACC 1.083,1.427 1.594,1.573 0.51,0.146 10 false DC/DC 2.208,1.115 2.323,1.26 0.115,0.146 10 false 1 2.083,1.292 2.417,1.438 0.333,0.146 10 false 2F*2 2.208,0.458 2.323,0.604 0.115,0.146 10 false 1 2.083,0.646 2.406,0.792 0.323,0.146 10 false 2E*1 5.427,1.115 5.615,1.26 0.188,0.146 10 false 29 5.396,1.302 5.635,1.448 0.24,0.146 10 false MB 5.719,1.302 6.125,1.479 0.406,0.177 10 false ACC 2.208,2.375 2.323,2.521 0.115,0.146 10 false 6 2.156,2.563 2.365,2.708 0.208,0.146 10 false 2B 2.208,2.969 2.323,3.115 0.115,0.146 10 false 4 2.156,3.146 2.365,3.292 0.208,0.146 10 false 2B 2.573,4.406 3.365,4.552 0.792,0.146 10 false *1: for LHD 3.698,4.406 4.49,4.552 0.792,0.146 10 false *2: for RHD 2.156,1.927 2.365,2.073 0.208,0.146 10 false 2A 2.156,1.75 2.344,1.896 0.188,0.146 10 false 43 4.333,1.427 5.26,1.573 0.927,0.146 10 false ECU-ACC 0.135,2.906 1,3.271 0.865,0.365 10 false from Auxiliary Battery 2.906,3.552 4.531,3.865 1.625,0.313 10 false Instrument Panel Junction Block Assembly 5.271,3.927 6.969,4.24 1.698,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 0.458,4.031 2.302,4.406 1.844,0.375 10 false from Certification ECU (Smart key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC (ENTRY AND START SYSTEM (for Start Function))
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR)

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Power switch ACC signal / ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2E*1 or 2F*2 instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2E-1 - Body ground*1 Power switch off 11 to 14 V
2F-1 - Body ground*2 Power switch off 11 to 14 V



*1: for LHD

*2: for RHD



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U191348E02
6.177,3.042 6.375,3.24 false 0.219,0.146 0.417,0.365 0.198,0.219 10 false *a 1.865,0.552 2.083,0.719 0.219,0.167 10 false 2A 5.365,0.552 5.583,0.719 0.219,0.167 10 false 2B 4.635,2.5 4.875,2.667 0.24,0.167 10 false MB 6.396,3.24 6.719,3.406 0.323,0.167 10 false ACC 0.823,2.323 1.063,2.49 0.24,0.167 10 false 2E 1.115,2.323 1.354,2.49 0.24,0.167 10 false *A 1.427,2.323 1.667,2.49 0.24,0.167 10 false 2F 1.719,2.323 1.958,2.49 0.24,0.167 10 false *B

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - MB-29 (ACC)*1 Always 10 kΩ or higher
2E-1 - MB-29 (ACC)*1 Auxiliary battery positive → 2A-43
Auxiliary battery negative → 2B-6, 2B-4
Below 1 Ω
2F-1 - MB-29 (ACC)*2 Always 10 kΩ or higher
2F-1 - MB-29 (ACC)*2 Auxiliary battery positive → 2A-43
Auxiliary battery negative → 2B-6, 2B-4
Below 1 Ω



*1: for LHD

*2: for RHD



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY