Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter sub-assembly receives signals from this circuit to adjust the illumination of the meter. The combination meter sub-assembly sets the illumination level based on the user operation of the light control rheostat switch.

HINT:
·

The meter illumination level can be adjusted by operating the hazard warning signal switch assembly (light control rheostat switch).


·

The meter illumination dims when the light control switch is turned to the tail, head, or AUTO position at night.


·

Setting the meter illumination to maximum brightness cancels the above dimming of the meter illumination.



WIRING DIAGRAM

E225731E05
2.469,1.26 2.656,1.49 0.188,0.229 10 false E 2.646,0.625 2.823,0.833 0.177,0.208 10 false 2 2.365,0.625 2.698,0.885 0.333,0.26 10 false CS 2.646,1.26 2.979,1.49 0.333,0.229 10 false 5 4.604,0.625 4.917,0.917 0.313,0.292 10 false 26 4.875,0.74 5.625,1.031 0.75,0.292 10 false TC O 4.406,1.75 4.708,1.927 0.302,0.177 10 false L27 4.406,1.896 6.479,2.25 2.073,0.354 10 false Combination Meter Sub-assembly 0.917,1.802 1.323,2.01 0.406,0.208 10 false L57 0.917,1.948 3.448,2.333 2.531,0.385 10 false Hazard Warning Signal Switch Assembly(Light Control Rheostat Switch)

PROCEDURE

1.READ VALUE USING GTS (LIGHT CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Light Control Switch Light control rheostat switch (hazard warning signal switch assembly) / OFF or ON OFF: Light control rheostat switch not pressed -
ON: Light control rheostat switch pressed

OK:

The value displayed on the GTS gradually changes as the actual light control rheostat switch operation.

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C




A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.
E190200E07
0.13,0.051 0.323,0.225 0.193,0.174 10 *a 2.688,1.757 2.835,1.932 0.147,0.174 10 E 2.04,0.297 2.274,0.455 0.235,0.158 10 CS 1.819,1.116 2.103,0.483 false 2.054,1.375 2.647,1.742 false

Remove the hazard warning signal switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (CS) - 5 (E) Light control rheostat switch pressed Below 1 Ω
Light control rheostat switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Light Control Rheostat)



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - HAZARD WARNING SIGNAL SWITCH ASSEMBLY)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - HAZARD WARNING SIGNAL SWITCH ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-26 (TC O) - L57-2 (CS) Always Below 1 Ω
L57-5 (E) - Body ground Always Below 1 Ω
L27-26 (TC O) - Body ground Always 10 kΩ or higher

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C




A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR