Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter sub-assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. DTC Detection Condition Trouble Area
B1507 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Open in turn signal light circuit


·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Combination meter sub-assembly


B1508 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Short in turn signal light circuit or hazard warning light circuit


·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Combination meter sub-assembly



WIRING DIAGRAM

E309023E03
3.979,6.688 5.75,7.344 1.771,0.656 10 false Instrument Panel Junction Block Assembly 1.344,1.073 3.51,1.396 2.167,0.323 10 false Headlight Assembly LH 1.156,0.729 1.448,0.906 0.292,0.177 10 false A85 1,2.188 3.417,2.51 2.417,0.323 10 false Rear Combination Light Assembly LH 1,2.031 1.292,2.208 0.292,0.177 10 false R17 0.969,3.292 3.469,3.615 2.5,0.323 10 false Outer Rear View Mirror Assembly LH*1 0.969,3.125 1.292,3.302 0.323,0.177 10 false O12 1.365,4.396 3.531,4.719 2.167,0.323 10 false Headlight Assembly RH 1,5.5 3.385,5.823 2.385,0.323 10 false Rear Combination Light Assembly RH 1,5.333 1.292,5.51 0.292,0.177 10 false S18 5.729,4.583 6.927,5.146 1.198,0.563 10 false Combination Meter Sub-assembly 5.729,4.417 6.146,4.594 0.417,0.177 10 false L125 5.344,4.042 5.542,4.219 0.198,0.177 10 false 2A 5.365,3.875 5.563,4.052 0.198,0.177 10 false 17 5.344,0.729 5.542,0.906 0.198,0.177 10 false 2A 5.365,0.542 5.563,0.719 0.198,0.177 10 false 22 3.865,4.052 4.063,4.229 0.198,0.177 10 false 2C 3.875,3.865 4.073,4.042 0.198,0.177 10 false 36 3.865,0.729 4.063,0.906 0.198,0.177 10 false 2C 3.865,0.531 4.063,0.708 0.198,0.177 10 false 17 3.865,1.813 4.063,1.99 0.198,0.177 10 false 2D 3.865,1.625 4.063,1.802 0.198,0.177 10 false 17 3.865,5.146 4.063,5.323 0.198,0.177 10 false 2D 3.906,4.969 4.083,5.146 0.177,0.177 10 false 4 5.958,0.625 6.156,0.802 0.198,0.177 10 false 3 5.969,3.969 6.167,4.146 0.198,0.177 10 false 5 6.125,4.063 6.323,4.24 0.198,0.177 10 false LR 6.135,0.719 6.333,0.896 0.198,0.177 10 false LL 2.521,1.74 2.646,1.917 0.125,0.177 10 false B 2.51,5.063 2.646,5.24 0.135,0.177 10 false B 1.531,1.75 1.844,1.927 0.313,0.177 10 false E 1.521,5.073 1.833,5.25 0.313,0.177 10 false E 2.708,1.74 3.021,1.917 0.313,0.177 10 false 6 1.354,1.75 1.51,1.927 0.156,0.177 10 false 5 1.24,0.542 1.396,0.719 0.156,0.177 10 false 6 2.708,5.063 3.021,5.24 0.313,0.177 10 false 6 1.344,5.063 1.5,5.24 0.156,0.177 10 false 5 3.865,2.927 4.063,3.104 0.198,0.177 10 false 2B 3.875,2.75 4.073,2.927 0.198,0.177 10 false 35 2.51,2.844 2.635,3.021 0.125,0.177 10 false B 1.531,2.854 1.844,3.031 0.313,0.177 10 false E 2.708,2.865 3.021,3.042 0.313,0.177 10 false 2 1.344,2.854 1.521,3.031 0.177,0.177 10 false 9 0.948,6.625 3.49,6.948 2.542,0.323 10 false Outer Rear View Mirror Assembly RH*1 0.948,6.479 1.24,6.656 0.292,0.177 10 false N12 3.854,6.26 4.052,6.438 0.198,0.177 10 false 2B 3.865,6.073 4.042,6.25 0.177,0.177 10 false 37 2.5,6.177 2.635,6.354 0.135,0.177 10 false B 1.521,6.177 1.833,6.354 0.313,0.177 10 false E 2.708,6.167 3.021,6.344 0.313,0.177 10 false 2 1.344,6.156 1.552,6.333 0.208,0.177 10 false 9 0.802,0.729 1.094,0.906 0.292,0.177 10 false A77 3.094,0.729 3.385,0.906 0.292,0.177 10 false A85 2.729,0.729 3.021,0.906 0.292,0.177 10 false A77 0.885,0.531 1.042,0.708 0.156,0.177 10 false 2 3.177,0.542 3.333,0.719 0.156,0.177 10 false 5 2.823,0.542 2.979,0.719 0.156,0.177 10 false 3 1.156,4.042 1.448,4.219 0.292,0.177 10 false A87 1.25,3.854 1.406,4.031 0.156,0.177 10 false 6 0.792,4.042 1.083,4.219 0.292,0.177 10 false A82 3.094,4.042 3.385,4.219 0.292,0.177 10 false A87 2.719,4.052 3.01,4.229 0.292,0.177 10 false A82 0.875,3.844 1.031,4.021 0.156,0.177 10 false 2 3.177,3.865 3.333,4.042 0.156,0.177 10 false 5 2.813,3.854 2.969,4.031 0.156,0.177 10 false 3 0.302,7.406 2.406,7.625 2.104,0.219 10 false *1: for Halogen Headlight Type 2.573,7.406 4.417,7.625 1.844,0.219 10 false *2: for LED Headlight Type 0.854,0.927 1.01,1.104 0.156,0.177 10 false *1 2.792,0.927 2.948,1.104 0.156,0.177 10 false *1 1.219,0.927 1.375,1.104 0.156,0.177 10 false *2 3.146,0.927 3.302,1.104 0.156,0.177 10 false *2 0.854,4.24 1.01,4.417 0.156,0.177 10 false *1 2.792,4.24 2.948,4.417 0.156,0.177 10 false *1 1.219,4.229 1.375,4.406 0.156,0.177 10 false *2 3.146,4.24 3.302,4.417 0.156,0.177 10 false *2 2.521,0.625 2.646,0.802 0.125,0.177 10 false B 1.531,0.625 1.844,0.802 0.313,0.177 10 false E 2.51,3.948 2.635,4.125 0.125,0.177 10 false B 1.521,3.948 1.833,4.125 0.313,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate. B
Rear turn signal light does not illuminate. C
Side turn signal light does not illuminate. D




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the L125 combination meter sub-assembly connector.


b.

Disconnect the 2A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
L125-3 (LL) - 2A-22 Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
L125-5 (LR) - 2A-17 Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
L125-3 (LL) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
L125-5 (LR) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

for Halogen headlight type

i.

Disconnect the A77*1 or A82*2 front turn signal light connector.

*1: for LH

*2: for RH



ii.

Disconnect the 2C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A77-3 - 2C-17 Always Below 1 Ω
A77-2 - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A82-3 - 2C-36 Always Below 1 Ω
A82-2 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A77-3 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A82-3 - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




b.

for LED headlight type

i.

Disconnect the A85*1 or A87*2 front turn signal light connector.

*1: for LH

*2: for RH



ii.

Disconnect the 2C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A85-5 - 2C-17 Always Below 1 Ω
A85-6 - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A87-5 - 2C-36 Always Below 1 Ω
A87-6 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A85-5 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A87-5 - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B





A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the R17*1 or S18*2 rear turn signal light connector.

*1: for LH

*2: for RH



b.

Disconnect the 2D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
R17-6 (B) - 2D-17 Always Below 1 Ω
R17-5 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
S18-6 (B) - 2D-4 Always Below 1 Ω
S18-5 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
R17-6 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
S18-6 (B) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the O12*1 or N12*2 outer rear view mirror assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 2B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
O12-2 (B) - 2B-35 Always Below 1 Ω
O12-9 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
N12-2 (B) - 2B-37 Always Below 1 Ω
N12-9 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
O12-2 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
N12-2 (B) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U155107E03
2.156,0.229 2.427,0.385 0.271,0.156 10 false 2A 5.115,0.229 5.385,0.385 0.271,0.156 10 false 2B 5.115,1.604 5.385,1.76 0.271,0.156 10 false 2D 2.156,1.615 2.427,1.771 0.271,0.156 10 false 2C 0.104,0.052 0.375,0.208 0.271,0.156 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-22 - 2C-17 Always Below 1 Ω
2A-22 - 2D-17 Always Below 1 Ω
2A-22 - 2B-35 Always Below 1 Ω
2A-17 - 2C-36 Always Below 1 Ω
2A-17 - 2D-4 Always Below 1 Ω
2A-17 - 2B-37 Always Below 1 Ω

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C




A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY