Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag ECU assembly and air conditioning control assembly (passenger airbag ON/OFF indicator).

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. DTC Detection Condition Trouble Area
B1660/43
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit.

·

Air conditioning control assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Air conditioning control assembly (Passenger airbag ON/OFF indicator)

·

Airbag ECU assembly



WIRING DIAGRAM

C264460E01
1.306,1.071 1.729,1.245 0.423,0.174 10 PAON 1.382,2.075 1.730,2.250 0.348,0.174 10 P-AB 1.478,3.065 1.731,3.240 0.253,0.174 10 IG+ 1.805,2.956 1.983,3.126 0.178,0.170 10 16 1.805,1.966 2.123,2.136 0.318,0.170 10 13 1.805,0.957 1.998,1.127 0.193,0.170 10 5 5.507,1.071 5.927,1.245 0.420,0.174 10 PAON 5.507,2.075 5.947,2.250 0.440,0.174 10 P-A/B 5.507,3.065 5.719,3.240 0.211,0.174 10 E1 5.507,4.074 5.719,4.248 0.211,0.174 10 E2 5.246,2.956 5.436,3.126 0.190,0.170 10 25 5.246,3.96 5.440,4.130 0.195,0.170 10 26 5.246,1.966 5.426,2.136 0.181,0.170 10 17 5.246,0.957 5.436,1.127 0.190,0.170 10 23 2.453,4.032 3.821,4.211 1.368,0.179 10 from IG1 NO. 1 Relay 0.568,4.765 0.886,4.949 0.318,0.184 10 L20 0.568,4.957 2.979,5.307 2.411,0.350 10 Air Conditioning Control Assembly (Passenger Airbag ON/OFF Indicator) 5.415,4.765 5.733,4.949 0.318,0.184 10 L16 5.415,4.957 6.986,5.134 1.570,0.177 10 Airbag ECU Assembly 2.286,3.22 2.542,3.371 0.256,0.151 10 A/C

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the power switch on (IG).


b.

Check the passenger airbag ON/OFF indicator operation.

Result:
ON/OFF Indicator Illumination Proceed to
Always ON A
OFF B


HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).




A

2.CHECK CONNECTORS

B

9.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and air conditioning control assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and air conditioning control assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the air conditioning control assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE (OPEN)
4.CHECK DTC
a.
C238328E01
0.67,0.774 0.853,0.934 0.184,0.161 10 *1 1.873,0.774 2.057,0.934 0.184,0.161 10 A 1.72,0.774 1.903,0.934 0.184,0.161 10 B 1.252,0.774 1.436,0.934 0.184,0.161 10 C 1.084,0.774 1.267,0.934 0.184,0.161 10 D 2.337,1.082 2.520,1.243 0.184,0.161 10 *2

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Connect the connector to the airbag ECU assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U191099E02
1.865,0.573 2.24,1.156 true 1.5,0.771 1.208,1.167 true 1.729,1.01 1.729,1.198 false 1.542,2.156 1.542,2.375 false 1.375,3.802 1.375,3.344 1.375,3.344 1.51,3.344 true 1.375,4.021 1.375,4.385 1.375,4.385 1.51,4.385 true 0.646,0.177 0.823,0.354 0.177,0.177 10 false *a 1.458,2.396 1.615,2.573 0.156,0.177 10 false *3 0.302,3.271 0.51,3.469 0.208,0.198 10 false *b 0.458,2.01 0.656,2.156 0.198,0.146 10 false *1 2.563,2.323 2.74,2.521 0.177,0.198 10 false *2 1.542,3.271 2,3.427 0.458,0.156 10 false PAON 2.302,1.083 2.688,1.25 0.385,0.167 10 false P-A/B 0.427,3.792 0.781,3.969 0.354,0.177 10 false L20 0.76,0.5 1.031,0.677 0.271,0.177 10 false L16 0.688,1.083 1.115,1.26 0.427,0.177 10 false PAON 1.542,4.302 1.896,4.448 0.354,0.146 10 false P-AB 1.802,2.01 1.948,2.177 0.146,0.167 10 false B 0.885,2.01 1.031,2.177 0.146,0.167 10 false D 1.177,2.01 1.323,2.177 0.146,0.167 10 false C 2.083,2.01 2.229,2.177 0.146,0.167 10 false A 1.635,1.219 1.792,1.385 0.156,0.167 10 false *4

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the air conditioning control assembly.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - L20-13 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.

Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT)
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - L20-13 (P-AB) Always 1 MΩ or higher


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L20-5 (PAON) - Body ground Power switch on (IG) Below 1 V
L20-13 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - Body ground Always 1 MΩ or higher
L20-13 (P-AB) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and air conditioning control assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and air conditioning control assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

10.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U191099E02
1.865,0.573 2.24,1.156 true 1.5,0.771 1.208,1.167 true 1.729,1.01 1.729,1.198 false 1.542,2.156 1.542,2.375 false 1.375,3.802 1.375,3.344 1.375,3.344 1.51,3.344 true 1.375,4.021 1.375,4.385 1.375,4.385 1.51,4.385 true 0.646,0.177 0.823,0.354 0.177,0.177 10 false *a 1.458,2.396 1.615,2.573 0.156,0.177 10 false *3 0.302,3.271 0.51,3.469 0.208,0.198 10 false *b 0.458,2.01 0.656,2.156 0.198,0.146 10 false *1 2.563,2.323 2.74,2.521 0.177,0.198 10 false *2 1.542,3.271 2,3.427 0.458,0.156 10 false PAON 2.302,1.083 2.688,1.25 0.385,0.167 10 false P-A/B 0.427,3.792 0.781,3.969 0.354,0.177 10 false L20 0.76,0.5 1.031,0.677 0.271,0.177 10 false L16 0.688,1.083 1.115,1.26 0.427,0.177 10 false PAON 1.542,4.302 1.896,4.448 0.354,0.146 10 false P-AB 1.802,2.01 1.948,2.177 0.146,0.167 10 false B 0.885,2.01 1.031,2.177 0.146,0.167 10 false D 1.177,2.01 1.323,2.177 0.146,0.167 10 false C 2.083,2.01 2.229,2.177 0.146,0.167 10 false A 1.635,1.219 1.792,1.385 0.156,0.167 10 false *4

Using a service wire, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - L20-13 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

11.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - L20-13 (P-AB) Always 1 MΩ or higher


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L20-5 (PAON) - Body ground Power switch on (IG) Below 1 V
L20-13 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

13.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U191100E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 1.676,1.897 2.137,2.049 0.461,0.152 10 PAON 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 1.696,2.995 2.088,3.141 0.392,0.146 10 P-AB 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.428,2.479 1.428,1.983 1.428,1.983 1.646,1.983 false 1.428,2.702 1.428,3.073 1.428,3.073 1.646,3.073 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-5 (PAON) - Body ground Always 1 MΩ or higher
L20-13 (P-AB) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

14.CHECK AIR CONDITIONING CONTROL ASSEMBLY (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK AIR CONDITIONING CONTROL ASSEMBLY (SOURCE VOLTAGE)
a.
U191101E01
1.207,0.127 1.362,0.273 0.155,0.146 10 *3 0.231,1.881 0.442,2.077 0.211,0.196 10 *a 0.446,0.654 0.643,0.799 0.198,0.145 10 *1 2.591,0.968 2.770,1.164 0.179,0.196 10 *2 0.395,2.468 0.745,2.647 0.350,0.179 10 L20 2.033,2.577 2.278,2.723 0.245,0.146 10 IG+ 1.831,0.654 1.973,0.824 0.142,0.170 10 B 0.852,0.654 0.994,0.824 0.142,0.170 10 D 1.148,0.654 1.290,0.824 0.142,0.170 10 C 2.122,0.654 2.264,0.824 0.142,0.170 10 A 1.546,0.675 1.546,0.206 1.546,0.206 1.398,0.206 false 1.746,2.658 2.012,2.658 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L20-16 (IG+) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR AUXILIARY BATTERY

15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
U191114E01
1.726,0.087 1.881,0.235 0.155,0.148 10 *3 0.833,1.862 1.045,2.058 0.211,0.196 10 *a 0.549,0.624 0.746,0.770 0.198,0.145 10 *1 2.528,0.933 2.707,1.129 0.179,0.196 10 *2 1.315,2.885 1.729,3.037 0.414,0.152 10 PAON 0.978,2.289 1.328,2.468 0.350,0.179 10 L16 2.191,2.885 2.574,3.031 0.383,0.146 10 P-A/B 1.75,0.613 1.892,0.783 0.142,0.170 10 B 0.955,0.613 1.097,0.783 0.142,0.170 10 D 1.113,0.613 1.255,0.783 0.142,0.170 10 C 2.041,0.613 2.183,0.783 0.142,0.170 10 A 2.092,2.415 2.389,2.871 false 1.747,2.608 1.576,2.871 false 1.489,0.64 1.489,0.178 1.489,0.178 1.695,0.178 false

Connect the connector to the air conditioning control assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
L16-23 (PAON) - Body ground Power switch on (IG) "ON" comes on
L16-17 (P-A/B) - Body ground Power switch on (IG) "OFF" comes on



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)



OK

16.CHECK DTC

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

16.CHECK DTC
a.
C238328E01
0.67,0.774 0.853,0.934 0.184,0.161 10 *1 1.873,0.774 2.057,0.934 0.184,0.161 10 A 1.72,0.774 1.903,0.934 0.184,0.161 10 B 1.252,0.774 1.436,0.934 0.184,0.161 10 C 1.084,0.774 1.267,0.934 0.184,0.161 10 D 2.337,1.082 2.520,1.243 0.184,0.161 10 *2

Connect the connector to the airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Air Conditioning Control Assembly
*2 Airbag ECU Assembly



OK

NG