Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The driving support ECU assembly sends information on steering angle and steering direction to the millimeter wave radar sensor. The millimeter wave radar sensor then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the power management control ECU and performs cruise control.

DTC No. DTC Detection Condition Trouble Area
U0235 When the power switch is on (IG), a communication error from the millimeter wave radar sensor to the driving support ECU assembly is detected for approx. 2 seconds.
·

Millimeter wave radar sensor

·

Driving support ECU assembly

·

Wire harness or connector



WIRING DIAGRAM

E228700E01
1.712,0.691 1.969,0.866 0.257,0.174 10 IGB 1.572,1.009 1.968,1.183 0.396,0.174 10 LRRD 3.694,0.349 4.626,0.523 0.932,0.174 10 ECU-IG NO. 2 2.029,0.214 3.389,0.388 1.360,0.174 10 from IG1 NO. 1 Relay 1.572,1.326 1.968,1.501 0.396,0.174 10 LRDD 1.548,1.644 1.967,1.819 0.420,0.174 10 SGND 5.212,0.691 5.336,0.866 0.124,0.174 10 B 4.959,0.608 5.135,0.783 0.175,0.174 10 30 4.959,1.556 5.135,1.731 0.175,0.174 10 25 4.959,1.24 5.135,1.414 0.175,0.174 10 16 4.959,0.926 5.135,1.101 0.175,0.174 10 38 2.04,0.607 2.196,0.782 0.156,0.174 10 5 2.04,1.556 2.196,1.731 0.156,0.174 10 2 2.04,1.24 2.196,1.414 0.156,0.174 10 3 2.04,0.926 2.196,1.101 0.156,0.174 10 4 5.212,1.009 5.609,1.183 0.397,0.174 10 LRRD 5.212,1.326 5.609,1.501 0.397,0.174 10 LRDD 5.212,1.644 5.609,1.819 0.397,0.174 10 GND 4.794,1.951 5.214,2.125 0.420,0.174 10 L60 4.794,2.11 6.773,2.284 1.979,0.174 10 Driving Support ECU Assembly 0.448,1.951 0.674,2.125 0.226,0.174 10 A2 0.448,2.11 2.351,2.284 1.903,0.174 10 Millimeter Wave Radar Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor with a new one, make sure to perform Adjust Millimeter Wave Radar Sensor Assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

Confirm that the connector is securely connected, as a partially connected connector is suspected for the cause of this DTC.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the L60 driving support ECU assembly connector.


b.

Disconnect the A2 millimeter wave radar sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-3 (LRDD) - L60-16 (LRDD) Always Below 1 Ω
A2-3 (LRDD) - Body ground Always 10 kΩ or higher
A2-4 (LRRD) - L60-38 (LRRD) Always Below 1 Ω
A2-4 (LRRD) - Body ground Always 10 kΩ or higher
A2-2 (SGND) - Body ground Always Below 1 Ω
L60-25 (GND) - Body ground Always Below 1 Ω




OK

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR)

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B CIRCUIT)
a.

Turn the power switch on (IG).


b.
U191313E01
2.501,0.205 2.753,0.361 0.251,0.156 10 L60 0.179,0.158 0.342,0.314 0.163,0.156 10 *a 1.807,1.792 1.921,1.948 0.114,0.156 10 B 1.773,1.535 1.868,1.774 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

3.CHECK MILLIMETER WAVE RADAR SENSOR (IGB CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (B CIRCUIT)

3.CHECK MILLIMETER WAVE RADAR SENSOR (IGB CIRCUIT)
a.

Turn the power switch on (IG).


b.
U191312E01
0.418,0.986 0.614,1.141 0.196,0.156 10 A2 0.143,0.13 0.307,0.285 0.163,0.156 10 *a 2.351,1.535 2.642,1.691 0.291,0.156 10 IGB 2.071,1.116 2.413,1.517 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A2-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor)


c.

Reconnect the A2 millimeter wave radar sensor connector.



OK

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (LRDD OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGB CIRCUIT)

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (LRDD OUTPUT VOLTAGE)
a.

Turn the power switch on (IG).


b.
U191314E01
2.504,0.205 2.766,0.361 0.262,0.156 10 L60 0.179,0.158 0.342,0.314 0.163,0.156 10 *a 2.021,1.757 2.433,1.913 0.413,0.156 10 LRDD 2.696,1.364 2.284,1.724 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-16 (LRDD) - Body ground Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

5.REPLACE DRIVING SUPPORT ECU

NG

5.REPLACE DRIVING SUPPORT ECU
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT

b.

Turn the cruise control main switch on.


c.

Check if the same DTC is output (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B




A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B