Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2016.05–2020.08
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301836 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter sub-assembly. The combination meter sub-assembly detects rear seat belt state. The rear seat belt warning light on the combination meter sub-assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B313256E04
2.291,0.446 2.716,0.623 0.425,0.177 10 RLSB 2.753,0.348 3.178,0.525 0.425,0.177 10 38 4.336,0.376 4.761,0.553 0.425,0.177 10 LBR+ 5.121,0.376 5.546,0.553 0.425,0.177 10 LBR- 4.336,1.511 4.761,1.688 0.425,0.177 10 CBR+ 5.093,1.511 5.518,1.688 0.425,0.177 10 CBR- 2.753,1.483 3.178,1.660 0.425,0.177 10 37 2.753,2.618 3.178,2.795 0.425,0.177 10 36 2.753,3.753 3.178,3.929 0.425,0.177 10 40 2.753,4.888 3.178,5.064 0.425,0.177 10 39 2.753,6.219 3.178,6.395 0.425,0.177 10 6 4.168,6.219 4.593,6.395 0.425,0.177 10 1 4.168,7.283 4.593,7.460 0.425,0.177 10 1 4.168,4.888 4.593,5.064 0.425,0.177 10 1 4.168,3.753 4.593,3.929 0.425,0.177 10 3 4.168,2.618 4.593,2.795 0.425,0.177 10 1 4.168,1.483 4.593,1.660 0.425,0.177 10 1 4.336,2.638 4.761,2.815 0.425,0.177 10 RBR+ 5.093,2.638 5.518,2.815 0.425,0.177 10 RBR- 4.336,3.781 4.552,3.957 0.216,0.177 10 + 5.331,3.781 5.492,3.957 0.161,0.177 10 E 4.336,4.911 4.552,5.087 0.216,0.177 10 + 5.331,4.911 5.492,5.087 0.161,0.177 10 E 4.168,0.348 4.593,0.525 0.425,0.177 10 1 4.028,0.628 4.453,0.805 0.425,0.177 10 R35 4.028,0.782 5.874,1.188 1.846,0.406 10 Rear Seat 3 Point Type Belt Assembly LH 3.916,1.819 4.341,1.996 0.425,0.177 10 R36 3.916,1.973 5.869,2.160 1.953,0.187 10 Rear Seat Inner Belt Assembly 4.168,2.954 4.593,3.131 0.425,0.177 10 S28 4.168,3.094 5.699,3.500 1.531,0.406 10 Rear Seat 3 Point Type Belt Assembly RH 4.063,4.089 4.488,4.226 0.425,0.137 10 S29 4.063,4.229 5.710,4.635 1.647,0.406 10 Rear No. 2 Seat Inner Belt Assembly LH 4.065,5.224 4.490,5.363 0.425,0.139 10 S29 4.065,5.364 5.712,5.677 1.647,0.313 10 Rear No. 2 Seat Inner Belt Assembly RH 4.028,6.513 4.453,6.689 0.425,0.177 10 R13 4.028,6.653 5.712,7.059 1.684,0.406 10 Rear Door Courtesy Light Switch Assembly LH 4.028,7.606 4.453,7.782 0.425,0.177 10 S10 4.028,7.746 5.712,8.152 1.684,0.406 10 Rear Door Courtesy Light Switch Assembly RH 5.541,0.348 5.966,0.525 0.425,0.177 10 2 5.541,1.483 5.966,1.660 0.425,0.177 10 2 5.541,2.618 5.966,2.795 0.425,0.177 10 2 5.541,3.753 5.966,3.929 0.425,0.177 10 2 5.541,4.888 5.966,5.064 0.425,0.177 10 4 0.714,5.35 1.139,5.527 0.425,0.177 10 L27 0.974,6.821 1.399,6.998 0.425,0.177 10 CAN 0.974,2.716 1.399,2.893 0.425,0.177 10 CAN 1.002,5.35 3.486,5.527 2.484,0.177 10 Combination Meter Sub-assembly*1 0.714,7.83 1.139,8.006 0.425,0.177 10 L201 0.7,8.53 2.448,8.707 1.748,0.177 10 : CAN Communication Line 1.058,7.83 2.795,8.291 1.737,0.461 10 Main Body ECU (Multiplex Network Body ECU) 2.277,1.581 2.702,1.758 0.425,0.177 10 RCSB 2.277,2.702 2.702,2.879 0.425,0.177 10 RRSB 2.305,3.851 2.730,4.028 0.425,0.177 10 RLBT 2.291,4.972 2.716,5.148 0.425,0.177 10 RRBT 2.291,6.303 2.716,6.479 0.425,0.177 10 LRCY 1.04,5.627 2.601,5.803 1.560,0.177 10 - Meter Circuit Plate*2 2.543,8.53 4.568,8.707 2.026,0.177 10 *1: w/ Multi-information Display 4.553,8.53 6.648,8.707 2.095,0.177 10 *2: w/o Multi-information Display

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING GTS (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch signal/ON or OFF ON: Rear door RH or LH open
OFF: Rear door RH and LH closed
-
RL Door Courtesy SW Rear door courtesy light switch signal/ON or OFF ON: Rear door LH or RH open
OFF: Rear door LH and RH closed
-

OK:

ON or OFF appears on the tester screen according to the rear door condition.




OK

2.CHECK REAR SEAT BELT WARNING

NG

2.CHECK REAR SEAT BELT WARNING
a.
B313255E01
0.207,0.197 0.361,0.334 0.154,0.137 10 *a 1.352,2.687 1.506,2.824 0.154,0.137 10 *b 1.683,2.687 1.824,2.824 0.141,0.137 10 *c 1.98,2.687 2.128,2.824 0.149,0.137 10 *d 1.49,3.058 1.639,3.195 0.149,0.137 10 *e 1.874,3.058 1.991,3.195 0.117,0.137 10 *f 1.435,2.065 1.435,2.667 false 1.575,2.288 1.575,3.048 false 1.927,2.288 1.927,3.048 false 1.753,2.065 1.753,2.667 false 2.063,2.065 2.063,2.667 false

Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).

Text in Illustration
*a Rear Seat Belt Warning Light (Combination Meter Sub-assembly)
*b Rear No. 1 Seat LH
*c Rear No. 1 Seat Center
*d Rear No. 1 Seat RH
*e Rear No. 2 Seat LH
*f Rear No. 2 Seat RH

Result:
Result Proceed to
The rear seat belt warning lights operation is normal A
The rear seat belt warning lights (all seat) operation is not normal (w/o Multi-information Display) B
The rear seat belt warning lights (all seat) operation is not normal (w/ Multi-information Display) C
The rear seat belt warning lights (any seat) operation is not normal D




A

B

3.REPLACE METER CIRCUIT PLATE

C

5.REPLACE COMBINATION METER SUB-ASSEMBLY

D

7.CHECK REAR SEAT BELT WARNING
3.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

4.CHECK REAR SEAT BELT WARNING
4.CHECK REAR SEAT BELT WARNING
a.

Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).

OK:

The rear seat belt warning function operates normally.




OK

END (METER CIRCUIT PLATE WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

6.CHECK REAR SEAT BELT WARNING
6.CHECK REAR SEAT BELT WARNING
a.

Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).

OK:

The rear seat belt warning function operates normally.




OK

END (COMBINATION METER SUB-ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK REAR SEAT BELT WARNING
a.
B313255E01
0.207,0.197 0.361,0.334 0.154,0.137 10 *a 1.352,2.687 1.506,2.824 0.154,0.137 10 *b 1.683,2.687 1.824,2.824 0.141,0.137 10 *c 1.98,2.687 2.128,2.824 0.149,0.137 10 *d 1.49,3.058 1.639,3.195 0.149,0.137 10 *e 1.874,3.058 1.991,3.195 0.117,0.137 10 *f 1.435,2.065 1.435,2.667 false 1.575,2.288 1.575,3.048 false 1.927,2.288 1.927,3.048 false 1.753,2.065 1.753,2.667 false 2.063,2.065 2.063,2.667 false

Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).

Text in Illustration
*a Rear Seat Belt Warning Light (Combination Meter Sub-assembly)
*b Rear No. 1 Seat LH
*c Rear No. 1 Seat Center
*d Rear No. 1 Seat RH
*e Rear No. 2 Seat LH
*f Rear No. 2 Seat RH

Result:
Result Proceed to
The rear seat belt warning light (rear No. 1 seat LH) operation is not normal A
The rear seat belt warning light (rear No. 1 seat center) operation is not normal B
The rear seat belt warning light (rear No. 1 seat RH) operation is not normal C
The rear seat belt warning light (rear No. 2 seat LH) operation is not normal D
The rear seat belt warning light (rear No. 2 seat RH) operation is not normal E




A

8.READ VALUE USING GTS (REAR NO. 1 SEAT BELT LH BUCKLE SWITCH)

B

10.READ VALUE USING GTS (REAR NO. 1 SEAT BELT CENTER BUCKLE SWITCH)

C

12.READ VALUE USING GTS (REAR NO. 1 SEAT BELT RH BUCKLE SWITCH)

D

14.READ VALUE USING GTS (REAR NO. 2 SEAT BELT LH BUCKLE SWITCH)

E

16.READ VALUE USING GTS (REAR NO. 2 SEAT BELT RH BUCKLE SWITCH)
8.READ VALUE USING GTS (REAR NO. 1 SEAT BELT LH BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (L) Rear No. 1 seat belt LH buckle switch signal/ON or OFF ON: Rear No. 1 seat belt LH not fastened
OFF: Rear No. 1 seat belt LH fastened
-

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition (w/ Multi-information Display) B
ON or OFF appears on the tester screen according to the rear seat belt condition (w/o Multi-information Display) C




A

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH - BODY GROUND)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the R35 rear seat 3 point type belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-38 (RLSB) - R35-1 (LBR+) Always Below 1 Ω
L27-38 (RLSB) - Body ground Always 10 kΩ or higher
R35-2 (LBR-) - Body ground Always Below 1 Ω




OK

REPLACE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (REAR NO. 1 SEAT BELT CENTER BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (C) Rear No. 1 seat belt center buckle switch signal/ON or OFF ON: Rear No. 1 seat belt center not fastened
OFF: Rear No. 1 seat belt center fastened
-

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition (w/ Multi-information Display) B
ON or OFF appears on the tester screen according to the rear seat belt condition (w/o Multi-information Display) C




A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the R36 rear seat inner belt assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-37 (RCSB) - R36-1 (CBR+) Always Below 1 Ω
L27-37 (RCSB) - Body ground Always 10 kΩ or higher
R36-2 (CBR-) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (REAR NO. 1 SEAT BELT RH BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear No. 1 seat belt RH buckle switch signal/ON or OFF ON: Rear No. 1 seat belt RH not fastened
OFF: Rear No. 1 seat belt RH fastened
-

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition (w/ Multi-information Display) B
ON or OFF appears on the tester screen according to the rear seat belt condition (w/o Multi-information Display) C




A

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH - BODY GROUND)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the S28 rear seat 3 point type belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-36 (RRSB) - S28-1 (RBR+) Always Below 1 Ω
L27-36 (RRSB) - Body ground Always 10 kΩ or higher
S28-2 (RBR-) - Body ground Always Below 1 Ω




OK

REPLACE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS (REAR NO. 2 SEAT BELT LH BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
3rd-Row Seatbelt Buckle (L) Rear No. 2 seat belt LH buckle switch signal/ON or OFF ON: Rear No. 2 seat belt LH not fastened
OFF: Rear No. 2 seat belt LH fastened
-

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition (w/ Multi-information Display) B
ON or OFF appears on the tester screen according to the rear seat belt condition (w/o Multi-information Display) C




A

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR NO. 2 SEAT INNER BELT ASSEMBLY LH - BODY GROUND)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR NO. 2 SEAT INNER BELT ASSEMBLY LH - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the S29 rear No. 2 seat inner belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-40 (RLBT) - S29-3 (+) Always Below 1 Ω
L27-40 (RLBT) - Body ground Always 10 kΩ or higher
S29-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.READ VALUE USING GTS (REAR NO. 2 SEAT BELT RH BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
3rd-Row Seatbelt Buckle (R) Rear No. 2 seat belt RH buckle switch signal/ON or OFF ON: Rear No. 2 seat belt RH not fastened
OFF: Rear No. 2 seat belt RH fastened
-

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition (w/ Multi-information Display) B
ON or OFF appears on the tester screen according to the rear seat belt condition (w/o Multi-information Display) C




A

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR NO. 2 SEAT INNER BELT ASSEMBLY RH - BODY GROUND)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - REAR NO. 2 SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the S29 rear No. 2 seat inner belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-39 (RRBT) - S29-1 (+) Always Below 1 Ω
L27-39 (RRBT) - Body ground Always 10 kΩ or higher
S29-4 (E) - Body ground Always Below 1 Ω




OK

REPLACE REAR NO. 2 SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR