Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P0AA6-611  Hybrid Battery Voltage System Isolation Fault  


DESCRIPTION

This DTC is stored if there is insulation trouble with the high-voltage circuit in the air conditioning system. Possible causes are poor insulation in the compressor with motor assembly, or mixing of any oil other than ND-OIL 11 in the refrigerant cycle.

A high-voltage motor is built into the electrical compressor and is cooled directly with refrigerant. Compressor oil (ND-OIL 11) with high insulation performance is used because a leakage of electrical power may occur if regular compressor oil (ND-OIL 8) is used.

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



DTC No. DTC Detection Condition Trouble Area
P0AA6-611 High voltage system insulation malfunction
·

Compressor oil

·

Refrigerant pipe line

·

Compressor with motor assembly

·

CAN communication system



WIRING DIAGRAM

E230287E05
0.146,6.313 1.594,6.833 1.448,0.521 10 false Compressor with Motor Assembly 5.76,3.906 7,4.281 1.24,0.375 10 false Power Management Control ECU 6.104,1.865 6.396,2.01 0.292,0.146 10 false STB 6.104,2.885 6.396,3.031 0.292,0.146 10 false ITE 6.063,3.375 6.354,3.521 0.292,0.146 10 false CLK 6.104,2.354 6.344,2.5 0.24,0.146 10 false ETI 0.802,1.823 1.177,1.969 0.375,0.146 10 false STBI 0.896,2.865 1.156,3.01 0.26,0.146 10 false DIN 0.865,3.354 1.156,3.5 0.292,0.146 10 false CLK 0.896,3.927 1.156,4.073 0.26,0.146 10 false IG1 0.823,4.5 1.156,4.646 0.333,0.146 10 false GND 0.948,5.281 1.188,5.427 0.24,0.146 10 false PE 0.948,5.771 1.167,5.917 0.219,0.146 10 false PB 0.74,2.313 1.156,2.458 0.417,0.146 10 false DOUT 1.302,1.844 1.573,1.99 0.271,0.146 10 false D12 1.302,2.354 1.573,2.5 0.271,0.146 10 false D12 1.302,2.865 1.573,3.01 0.271,0.146 10 false D12 1.302,3.354 1.573,3.5 0.271,0.146 10 false D12 1.302,4.5 1.573,4.646 0.271,0.146 10 false D12 1.302,3.917 1.573,4.063 0.271,0.146 10 false D12 5.781,1.719 6,1.927 0.219,0.208 10 false 20 5.792,2.229 6.031,2.438 0.24,0.208 10 false 30 5.792,2.74 6.083,2.948 0.292,0.208 10 false 31 5.781,3.25 5.969,3.396 0.188,0.146 10 false 19 4.927,7.219 7.094,7.479 2.167,0.26 10 false Inverter with Converter Assembly 5.188,5.677 5.292,5.823 0.104,0.146 10 false 1 5.188,5.146 5.292,5.313 0.104,0.167 10 false 2 1.354,5.281 1.563,5.427 0.208,0.146 10 false E1 1.344,5.781 1.583,5.927 0.24,0.146 10 false E1 1.385,5.052 1.49,5.198 0.104,0.146 10 false 1 1.385,5.573 1.49,5.74 0.104,0.167 10 false 2 1.385,1.625 1.49,1.771 0.104,0.146 10 false 4 1.385,2.135 1.49,2.302 0.104,0.167 10 false 3 1.385,2.625 1.49,2.771 0.104,0.146 10 false 2 1.385,3.146 1.49,3.313 0.104,0.167 10 false 1 1.385,3.719 1.49,3.865 0.104,0.146 10 false 6 1.385,4.271 1.49,4.438 0.104,0.167 10 false 5 5.438,5.146 5.844,5.292 0.406,0.146 10 false ACPE 5.438,5.646 5.844,5.792 0.406,0.146 10 false ACPB 5.719,5.948 6.219,6.5 0.5,0.552 10 false Electric Vehicle Fuse 2.698,4.094 2.99,4.24 0.292,0.146 10 false A/C 4.198,3.906 5.594,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.146 3.979,7.292 1.719,0.146 10 false : CAN Communication Line 4.927,7.042 5.177,7.25 0.25,0.208 10 false E3 5.76,3.74 6.479,3.969 0.719,0.229 10 false A21 0.177,1.063 2.448,1.26 2.271,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.323 3.938,6.552 1.208,0.229 10 false No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing the DTC to be output.

·

If other oil is accidentally used and a DTC is output, collect as much oil in the refrigerant cycle as possible into the compressor and replace it with ND-OIL 11 to increase the ND-OIL 11 ratio amount.

·

Replace the main components (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing the DTC to be output.

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

If it can be confirmed that any compressor oil other than ND-OIL 11 has been used in the vehicle, replace the main components of the air conditioning cycle.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

B

2.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Because the compressor has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.



b.

Turn the power switch on (READY).


c.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C Switch On


d.

Turn the power switch off.


e.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



f.
U191289E02
0.875,2.167 1.563,1.729 false 2.552,2.167 1.969,1.729 false 0.615,2.094 0.823,2.292 0.208,0.198 10 false PB 0.365,0.344 0.573,0.542 0.208,0.198 10 false *a 2.573,2.094 2.781,2.292 0.208,0.198 10 false PE 1.667,0.917 1.875,1.083 0.208,0.167 10 false E1

Disconnect the E1 compressor with motor assembly connector.


g.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-1 (PE) - Body ground Always 2 MΩ or higher
E1-2 (PB) - Body ground Always 2 MΩ or higher


Text in Illustration
*a Component without harness connected
(Compressor with Motor Assembly)



OK

3.INSPECT AIR CONDITIONING CYCLE

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

3.INSPECT AIR CONDITIONING CYCLE
CAUTION:

Because the compressor has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


a.

Reconnect the E1 compressor with motor assembly connector.



c.

Turn the power switch on (IG).


d.

Set the A/C temperature to 25°C (77°F) and the blower switch to LO and then operate the compressor for 10 minutes to circulate the refrigerant and collect as much compressor oil as possible in the compressor.


e.

Turn the power switch off.


f.

Using a spot cooler or other tools, cool down the compressor with motor assembly for 30 minutes, or leave the vehicle overnight before inspection.

NOTICE:

Do not operate the compressor before inspection.



g.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



h.
U191289E02
0.875,2.167 1.563,1.729 false 2.552,2.167 1.969,1.729 false 0.615,2.094 0.823,2.292 0.208,0.198 10 false PB 0.365,0.344 0.573,0.542 0.208,0.198 10 false *a 2.573,2.094 2.781,2.292 0.208,0.198 10 false PE 1.667,0.917 1.875,1.083 0.208,0.167 10 false E1

Disconnect the E1 compressor with motor assembly connector.


i.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-1 (PE) - Body ground Always 3 MΩ or higher
E1-2 (PB) - Body ground Always 3 MΩ or higher


NOTICE:

If the results are out of the specified range, replace the compressor without operating it.


Text in Illustration
*a Component without harness connected
(Compressor with Motor Assembly)



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE AIR CONDITIONING CYCLE