The solar sensor (automatic light control sensor) is installed on the upper side of the instrument panel. It detects sunlight to control air conditioning AUTO mode. The output voltage from the solar sensor (automatic light control sensor) varies in accordance with the amount of sunlight. When the amount of sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the solar sensor (automatic light control sensor).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B14A2 | Short in driver side solar sensor (automatic light control sensor) circuit | ·
Solar sensor (automatic light control sensor) ·
Harness or connector between solar sensor (automatic light control sensor) and air conditioning amplifier assembly ·
Harness or connector between solar sensor (automatic light control sensor) and main body ECU (multiplex network body ECU) ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly |
If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>B1244).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Solar Sensor (D side) | Solar sensor (automatic light control sensor) /
Min.: 0 Max.: 255 |
Solar sensor value increases as brightness increases | - |
The display is as specified in the Normal Condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
(See pageVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>PROBLEM SYMPTOMS TABLE)
C
Disconnect the I1 solar sensor (automatic light control sensor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I1-3 (CLTB) - I1-6 (CLTE) | Power switch off | Below 1 V |
| I1-3 (CLTB) - I1-6 (CLTE) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Solar Sensor (Automatic Light Control Sensor)) |
OK
NG
Disconnect the L17 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L17-33 (TS) - I1-1 (NSHA) | Always | Below 1 Ω |
| L17-33 (TS) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the solar sensor (automatic light control sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).
Reconnect the I1 solar sensor (automatic light control sensor) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I1-1 (NSHA) - I1-6 (CLTE) | Sensor is exposed to electric light | 0.8 to 4.3 V |
| I1-1 (NSHA) - I1-6 (CLTE) | Sensor is covered with a cloth | Below 0.8 V |
The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the positive (+) lead to terminal 6 and the negative (-) lead to terminal 1 of the solar sensor (automatic light control sensor).
While using the auxiliary battery during inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.
Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor (automatic light control sensor).
As the inspection light is moved away from the sensor, the voltage decreases.
| *a | Component with harness connected
(Solar Sensor (Automatic Light Control Sensor)) |
OK
NG
Disconnect the L7 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L7-20 (CLTB) - I1-3 (CLTB) | Always | Blow 1 Ω |
| L7-22 (CLTE) - I1-6 (CLTE) | Always | Blow 1 Ω |
| L7-20 (CLTB) - Body ground | Always | 10 kΩ or higher |
| L7-22 (CLTE) - Body ground | Always | 10 kΩ or higher |
OK
NG