1.INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
When using a new upper instrument panel sub-assembly:
Immediately before installing the upper instrument panel assembly, twist and cut off the portion shown in the illustration.
Engage the 5 claws (B) as shown in the illustration.
Engage the 7 claws (A) as shown in the illustration.
Do not damage the upper instrument panel assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the 2 bolts <A>.
Install the 2 passenger airbag bolts <B>.
Connect the connector to install the upper instrument panel assembly.
82143C
2.CONNECT NO. 3 INSTRUMENT PANEL WIRE
55414A
3.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/ Headup Display)
Engage the 2 guides and 5 claws to install the instrument cluster finish panel end as shown in the illustration.
55404D
4.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Engage the 3 guide and 2 clips.
Install the instrument cluster finish panel sub-assembly with the 2 screws <D> and 3 clips.
55085
5.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Engage the 2 guides as shown in the illustration.
Install the No. 2 heater to register duct sub-assembly with the 2 clips.
55406B
6.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Engage the 2 claws to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.
7.INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 8 claws to install the center instrument panel register assembly.
86160P
8.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
Use the same procedure as for the LH side (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION).
55409F
9.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides and 5 claws to install the No. 2 instrument panel speaker panel sub-assembly.
62225A
10.INSTALL LOWER FRONT PILLAR GARNISH RH
Engage the 3 claws to install the lower front pillar garnish RH.
62211
11.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION)
55435A
12.INSTALL INSTRUMENT PANEL FINISH PANEL END RH
Connect the connector.
Engage the guide as shown in the illustration.
Engage the guide and 6 claws to install the instrument panel finish panel end RH as shown in the illustration.
62311B
13.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
55620C
14.INSTALL INSTRUMENT PANEL CUP HOLDER
Install the instrument panel cup holder with the 2 screws <E>.
15.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 6 claws.
Install the No. 2 instrument panel register assembly with the screw <C>.
55440D
16.INSTALL INSTRUMENT PANEL BOX ASSEMBLY
Open the instrument panel box and glove compartment door.
Engage the 8 claws to install the instrument panel box assembly.
Close the instrument panel box and glove compartment door.
86160P
17.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
55408F
18.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides and 5 claws to install the No. 1 instrument panel speaker panel sub-assembly.
62226
19.INSTALL LOWER FRONT PILLAR GARNISH LH
Engage the 3 claws to install the lower front pillar garnish LH.
62212
20.INSTALL FRONT PILLAR GARNISH LH
55436A
21.INSTALL INSTRUMENT PANEL FINISH PANEL END LH
Engage the guide as shown in the illustration.
Engage the guide and 6 claws to install the instrument panel finish panel end LH as shown in the illustration.
62312B
22.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
23.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
w/ Headup display:
Connect the connector.
Engage the 6 claws to install the No. 1 instrument panel register assembly.
55044B
24.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Engage the 8 claws to install the upper instrument panel finish panel sub-assembly.
55480D
25.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Engage each connector.
Engage the 8 claws and clip to install the lower instrument panel finish panel assembly.
55431B
26.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL
Engage the 2 claws and clip to install the upper instrument panel finish panel.
27.INSTALL INTEGRATION CONTROL AND PANEL
Engage each connector.
Engage the 8 claws to install the integration control and panel.
28.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
64995
29.INSTALL DECK FLOOR BOX RH
64993
30.INSTALL REAR DECK FLOOR BOX
58411A
31.INSTALL NO. 1 DECK BOARD
58412A
32.INSTALL NO. 2 DECK BOARD
58410B
33.INSTALL DECK BOARD ASSEMBLY
34.INSPECT SRS WARNING LIGHT