The roof sunshade ECU (sliding roof drive gear assembly) receives a door lock linked close operation request signal from the main body ECU (multiplex network body ECU) via the LIN communication when the wireless door lock function, key-linked door lock function or entry door lock function is operated with the power switch off. Then, the roof sunshade ECU (sliding roof drive gear assembly) activates the roof sunshade motor to close until it is fully closed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The door lock linked close function can be customized. Make sure that the setting is ON (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>CUSTOMIZE PARAMETERS).
When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).
Since the roof sunshade system has functions that use LIN communication, first confirm that there is no malfunction in the LIN communication functions in accordance with the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
When the roof sunshade switch (map light assembly) is operated, check that the roof sunshade operates (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>OPERATION CHECK).
The roof sunshade operates normally.
OK
NG
Check the problem symptoms.
| Result | Proceed to |
|---|---|
| The door lock linked close function does not operate when the wireless door lock function, key-linked door lock function and entry door lock function are operated. | A |
| The door lock linked close function does not operate when the key-linked door lock function is operated. | B |
| The door lock linked close function does not operate when the wireless door lock function is operated. | C |
| The door lock linked close function does not operate when the entry door lock function is operated. | D |
A
B
C
D
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Ignition (Direct Signal) | Power switch signal/ON or OFF | ON: Power switch on (IG)
OFF: Power switch off |
- |
The GTS display changes according to switch operation as shown in the table.
OK
NG
Replace the roof sunshade ECU (sliding roof drive gear assembly) (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE>REMOVAL).
NEXT
Perform the initialization (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).
NEXT
Check that the door lock linked close function operates when the wireless door lock function, key-linked function and entry door lock function is operated (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>OPERATION CHECK).
The door lock linked close function operates normally.
OK
NG
Disconnect the z21 ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z21-5 (IG) - Body ground | Power switch off | Below 1 V |
OK
NG
Check the power door lock control system (key-linked door lock function) (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
The key-linked door lock function operates normally.
OK
NG
Check the wireless door lock control system (door lock function) (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
The wireless door lock function operates normally.
OK
NG
Check the entry and start system (for entry function) (entry door lock function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
The entry door lock function operates normally.
OK
NG