Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301870 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

a.
B274424E01
0.986,0.67 1.183,0.840 0.198,0.170 10 (1) 1.837,0.96 2.035,1.130 0.198,0.170 10 (2)

Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.

NOTICE:

Only the 2-piece type No. 1 windshield glass stoppers are supplied. Use the 2-piece type stoppers even if the 1-piece type stoppers were used.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a brush or a sponge, coat the application area of the No. 2 windshield glass stoppers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

B274425E01
0.147,0.139 0.351,0.313 0.204,0.174 10 *A 1.507,1.235 1.665,1.379 0.159,0.144 10 *1 1.309,1.563 1.496,1.3 false 1.428,0.853 1.587,0.997 0.159,0.144 10 *2 1.015,1.475 1.408,0.925 false 0.407,1.484 0.510,1.628 0.103,0.144 10 a 6.15,1.235 6.309,1.379 0.159,0.144 10 *1 5.952,1.563 6.139,1.3 false 6.071,0.853 6.230,0.997 0.159,0.144 10 *2 5.659,1.475 6.052,0.925 false 6.753,1.484 6.856,1.628 0.103,0.144 10 a

Text in Illustration
*A Back Side - -
*1 Ceramic Notch *2 Windshield Glass Edge Side

Standard Dimension:
Area Dimension
a 13.7 to 14.7 mm (0.539 to 0.578 in.)


NOTICE:

Only the 2-piece type No. 2 windshield glass stoppers are supplied. Use the 2-piece type stoppers even if the 1-piece type stoppers were used.



Hide 75533G 3.INSTALL WINDSHIELD OUTSIDE MOULDING (for Standard Roof)

a.

Using a brush or a sponge, coat the application area of a new windshield outside moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B274426E01
1.304,0.717 1.420,0.866 0.116,0.149 10 A 1.304,0.184 1.420,0.333 0.116,0.149 10 A 0.971,2.179 1.308,2.328 0.337,0.149 10 A - A 0.18,0.165 0.399,0.333 0.219,0.169 10 *A

Install the windshield outside moulding onto the windshield glass, as shown in the illustration.

Text in Illustration
*A Back Side


Hide 75534 4.INSTALL WINDSHIELD OUTSIDE MOULDING LH (for Glass Roof)

a.

Using a brush or a sponge, coat the application area of a new windshield outside moulding LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B318792E01
0.577,2.105 0.693,2.254 0.116,0.149 10 A 1.1,2.181 1.216,2.330 0.116,0.149 10 A 1.025,3.712 1.362,3.861 0.337,0.149 10 A - A 0.269,0.741 0.488,0.910 0.219,0.169 10 *A

Install the windshield outside moulding LH onto the windshield glass, as shown in the illustration.

Text in Illustration
*A Back Side


Hide 75533 5.INSTALL WINDSHIELD OUTSIDE MOULDING RH (for Glass Roof)

HINT:

Use the same procedure as for the LH side.


Hide 75549A 6.INSTALL WINDSHIELD OUTSIDE SUB MOULDING (for Glass Roof)

a.

Using a brush or a sponge, coat the application area of a new windshield outside sub moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B274427E01
1.312,1.681 1.428,1.830 0.116,0.149 10 A 1.304,1.131 1.420,1.280 0.116,0.149 10 A 1.019,3.141 1.356,3.290 0.337,0.149 10 A - A 0.617,0.13 0.733,0.279 0.116,0.149 10 a 2.735,0.129 2.851,0.278 0.116,0.149 10 a

Install the windshield outside sub moulding onto the windshield glass, as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.5 to 3.5 mm (0.0591 to 0.138 in.)


NOTICE:

Center the windshield outside sub moulding so that the distance from each end to the edges of the windshield glass is equal.



Hide 56117A 7.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or a sponge, coat the application area of a new window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the window glass adhesive dam onto the windshield glass, as shown in the illustration.

B274430E01
0.147,0.134 0.346,0.297 0.199,0.163 10 *A 3.289,1.893 3.404,2.042 0.116,0.149 10 A 4.903,1.014 5.240,1.163 0.337,0.149 10 A - A 3.321,2.394 3.437,2.543 0.116,0.149 10 A 5.35,1.565 5.452,1.714 0.102,0.149 10 a 1.549,2.933 1.706,3.082 0.157,0.149 10 *2 1.357,3.238 1.514,3.387 0.157,0.149 10 *3 0.589,3.364 0.746,3.513 0.157,0.149 10 *1 1.201,3.093 1.542,3.003 false 0.831,3.144 0.669,3.342 0.669,3.342 0.595,2.955 false 1.09,3.199 1.34,3.308 false 6.215,1.768 6.373,1.917 0.157,0.149 10 *1 5.891,1.742 6.185,1.835 6.185,1.835 5.888,1.946 false 3.141,2.942 3.299,3.091 0.157,0.149 10 *2 3.352,3.25 3.510,3.399 0.157,0.149 10 *3 4.14,3.312 4.297,3.461 0.157,0.149 10 *1 3.637,3.095 3.296,3.006 false 4.042,3.082 4.203,3.28 4.203,3.28 4.278,2.868 false 3.748,3.201 3.498,3.31 false 6.218,1.33 6.376,1.479 0.157,0.149 10 *2 6.021,1.503 6.207,1.396 false

Text in Illustration
*A Back Side - -
*1 Ceramic Notch *2 Window Glass Adhesive Dam
*3 Alignment Mark (Ceramic Notch) - -

Standard Dimension:
Area Dimension
a 2.6 mm (0.102 in.)



Hide 8.INSTALL WINDSHIELD GLASS

a.
B291620E01
1.375,0.787 1.532,0.935 0.157,0.149 10 *1 1.661,0.424 1.459,0.424 1.459,0.424 1.459,0.779 false 1.661,0.685 1.459,0.685 false

Position the windshield glass.

Text in Illustration
*1 Matchmark

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.

Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.



iv.

Remove the windshield glass.



b.

Using a brush, coat the installation surface on the vehicle body with body primer.

B283212E03
0.99,0.708 1.25,0.635 false 3.323,1.26 3.25,1.448 false 6.083,3.771 6.281,3.708 false 5.385,4.188 5.563,4.073 false 5.927,2.417 6.125,2.292 false 6.031,0.917 5.823,0.865 false 1.26,0.563 1.417,0.708 0.156,0.146 10 false *2 3.177,1.458 3.333,1.604 0.156,0.146 10 false *3 6.292,3.646 6.448,3.792 0.156,0.146 10 false *4 0.323,4.573 0.479,4.719 0.156,0.146 10 false *1 1.656,2.375 1.771,2.521 0.115,0.146 10 true B 2.75,3.198 2.875,3.344 0.125,0.146 10 false C 2.698,2.5 2.813,2.646 0.115,0.146 10 false A 4.979,1.813 5.313,1.958 0.333,0.146 10 false B - B 4.979,3.271 5.323,3.417 0.344,0.146 10 false C - C 4.979,0.354 5.313,0.5 0.333,0.146 10 false A - A 2.698,1.833 2.813,1.979 0.115,0.146 10 false A 2.313,2.51 2.427,2.656 0.115,0.146 10 false B 2.688,3.875 2.813,4.021 0.125,0.146 10 false C 5.229,4.115 5.385,4.26 0.156,0.146 10 false *4 6.135,2.219 6.292,2.365 0.156,0.146 10 false *4 5.677,0.802 5.833,0.948 0.156,0.146 10 false *4 1.938,0.354 2.094,0.5 0.156,0.146 10 false *a 3.021,0.354 3.177,0.5 0.156,0.146 10 false *b

Text in Illustration
*1 Body Primer *2 Brush
*3 Adhesive *4 Edge of Curved Surface
*a CORRECT *b WRONG

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than that specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



c.

Using a brush or a sponge, coat the adhesive application area with glass primer.

B274431E01
6.278,2.698 6.436,2.847 0.157,0.149 10 *2 1.021,2.633 1.179,2.782 0.157,0.149 10 *3 0.43,6.617 0.587,6.766 0.157,0.149 10 *1 1.198,5.636 1.300,5.785 0.102,0.149 10 b 3.231,3.74 3.333,3.889 0.102,0.149 10 c 3.152,5.626 3.254,5.775 0.102,0.149 10 d 5.619,4.194 5.721,4.343 0.102,0.149 10 e 1.205,3.809 1.306,3.958 0.102,0.149 10 a 0.147,0.134 0.346,0.297 0.199,0.163 10 *A 0.941,3.433 1.140,3.596 0.199,0.163 10 *B 2.818,0.537 2.934,0.686 0.116,0.149 10 B 2.89,1.077 3.006,1.226 0.116,0.149 10 B 2.691,1.347 2.821,1.496 0.130,0.149 10 C 2.837,2.085 2.967,2.234 0.130,0.149 10 D 2.212,0.585 2.328,0.734 0.116,0.149 10 A 2.213,1.262 2.329,1.411 0.116,0.149 10 A 0.941,4.61 1.154,4.773 0.213,0.163 10 *C 2.903,3.433 3.102,3.596 0.199,0.163 10 *B 2.903,4.61 3.116,4.773 0.213,0.163 10 *C 2.777,3.223 3.114,3.372 0.337,0.149 10 B - B 4.757,3.223 5.099,3.372 0.342,0.149 10 C - C 4.757,4.909 5.099,5.058 0.342,0.149 10 D - D 0.801,3.223 1.138,3.372 0.337,0.149 10 A - A 3.427,1.233 3.556,1.382 0.130,0.149 10 C 2.893,2.634 3.022,2.783 0.130,0.149 10 D 1.091,2.353 1.091,2.622 false 6.347,2.421 6.347,2.69 false 5.184,5.42 5.286,5.569 0.102,0.149 10 f 0.363,6.603 0.424,6.752 0.060,0.149 10 :

Text in Illustration
*A Back Side *B for Standard Roof
*C for Glass Roof - -
*1 Glass Primer *2 Ceramic Notch
*3 Adhesive Center - -

Standard Dimension:
Area Dimension
a 9.8 mm (0.386 in.) or more
b 9.6 mm (0.378 in.) or more
c 7.5 mm (0.295 in.)
d 7.3 mm (0.287 in.)
e 9.8 mm (0.386 in.) or more
f 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer onto the ceramic notches.

·

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E02
0.496,0.546 0.650,0.739 0.154,0.193 10 a 1.339,1.361 1.494,1.554 0.154,0.193 10 a 1.142,0.852 1.296,1.045 0.154,0.193 10 b 0.75,0.937 0.905,1.130 0.154,0.193 10 b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass as shown in the illustration.

B274432E01
6.274,2.707 6.431,2.856 0.157,0.149 10 *2 1.074,2.649 1.231,2.797 0.157,0.149 10 *3 0.356,6.598 0.514,6.746 0.157,0.149 10 *1 1.173,5.478 1.274,5.627 0.102,0.149 10 a 3.184,3.616 3.286,3.765 0.102,0.149 10 a 3.098,5.489 3.200,5.638 0.102,0.149 10 a 5.788,4.421 5.890,4.570 0.102,0.149 10 a 1.17,3.626 1.272,3.775 0.102,0.149 10 a 0.147,0.134 0.346,0.297 0.199,0.163 10 *A 0.871,3.447 1.070,3.610 0.199,0.163 10 *B 2.828,0.524 2.944,0.673 0.116,0.149 10 B 2.679,1.345 2.809,1.494 0.130,0.149 10 C 2.834,2.084 2.963,2.233 0.130,0.149 10 D 2.218,0.58 2.333,0.729 0.116,0.149 10 A 0.871,4.764 1.084,4.927 0.213,0.163 10 *C 2.847,3.447 3.046,3.610 0.199,0.163 10 *B 2.847,4.764 3.060,4.927 0.213,0.163 10 *C 2.777,3.223 3.114,3.372 0.337,0.149 10 B - B 4.757,3.223 5.099,3.372 0.342,0.149 10 C - C 4.757,4.909 5.099,5.058 0.342,0.149 10 D - D 0.801,3.223 1.138,3.372 0.337,0.149 10 A - A 2.217,1.256 2.333,1.405 0.116,0.149 10 A 2.886,1.085 3.002,1.234 0.116,0.149 10 B 3.439,1.24 3.569,1.389 0.130,0.149 10 C 2.901,2.629 3.031,2.778 0.130,0.149 10 D 6.169,5.403 6.271,5.552 0.102,0.149 10 b 5.122,5.209 5.224,5.358 0.102,0.149 10 c 0.284,6.584 0.344,6.733 0.060,0.149 10 : 1.144,2.356 1.144,2.635 false 6.347,2.421 6.347,2.7 false

Text in Illustration
*A Back Side *B for Standard Roof
*C for Glass Roof - -
*1 Adhesive *2 Ceramic Notch
*3 Adhesive Center - -

Standard Dimension:
Area Dimension
a 9.5 mm (0.374 in.)
b 6.6 mm (0.260 in.)
c 8.0 mm (0.315 in.)


HINT:

Apply adhesive onto the ceramic notches.




e.
B291620E01
1.375,0.787 1.532,0.935 0.157,0.149 10 *1 1.661,0.424 1.459,0.424 1.459,0.424 1.459,0.779 false 1.661,0.685 1.459,0.685 false

Install the windshield glass.

Text in Illustration
*1 Matchmark

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the windshield glass rim.



iv.

Hold the windshield glass using protective tape until applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 9.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 11.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87818 12.INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

Hide 13.CONNECT ROOF HEADLINING ASSEMBLY

Hide 55781E 14.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 55810F 15.INSTALL FRONT VENTILATOR ASSEMBLY

Hide 16.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 17.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85292B 18.INSTALL FRONT WIPER ARM HEAD CAP