When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.
56115A
1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER
Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.
Only the 2-piece type No. 1 windshield glass stoppers are supplied. Use the 2-piece type stoppers even if the 1-piece type stoppers were used.
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER
Using a brush or a sponge, coat the application area of the No. 2 windshield glass stoppers with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Windshield Glass Edge Side |
| Area | Dimension |
|---|---|
| a | 13.7 to 14.7 mm (0.539 to 0.578 in.) |
Only the 2-piece type No. 2 windshield glass stoppers are supplied. Use the 2-piece type stoppers even if the 1-piece type stoppers were used.
75533G
3.INSTALL WINDSHIELD OUTSIDE MOULDING (for Standard Roof)
Using a brush or a sponge, coat the application area of a new windshield outside moulding with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the windshield outside moulding onto the windshield glass, as shown in the illustration.
| *A | Back Side |
75534
4.INSTALL WINDSHIELD OUTSIDE MOULDING LH (for Glass Roof)
Using a brush or a sponge, coat the application area of a new windshield outside moulding LH with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the windshield outside moulding LH onto the windshield glass, as shown in the illustration.
| *A | Back Side |
75533
5.INSTALL WINDSHIELD OUTSIDE MOULDING RH (for Glass Roof)
Use the same procedure as for the LH side.
75549A
6.INSTALL WINDSHIELD OUTSIDE SUB MOULDING (for Glass Roof)
Using a brush or a sponge, coat the application area of a new windshield outside sub moulding with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the windshield outside sub moulding onto the windshield glass, as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 1.5 to 3.5 mm (0.0591 to 0.138 in.) |
Center the windshield outside sub moulding so that the distance from each end to the edges of the windshield glass is equal.
56117A
7.INSTALL WINDOW GLASS ADHESIVE DAM
Using a brush or a sponge, coat the application area of a new window glass adhesive dam with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the window glass adhesive dam onto the windshield glass, as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Window Glass Adhesive Dam |
| *3 | Alignment Mark (Ceramic Notch) | - | - |
| Area | Dimension |
|---|---|
| a | 2.6 mm (0.102 in.) |
8.INSTALL WINDSHIELD GLASS
Position the windshield glass.
| *1 | Matchmark |
Using suction cups, place the windshield glass in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
Align the matchmarks on the windshield glass and vehicle body.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Remove the windshield glass.
Using a brush, coat the installation surface on the vehicle body with body primer.
| *1 | Body Primer | *2 | Brush |
| *3 | Adhesive | *4 | Edge of Curved Surface |
| *a | CORRECT | *b | WRONG |
Do not coat the adhesive with body primer.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
If an area other than that specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.
Using a brush or a sponge, coat the adhesive application area with glass primer.
| *A | Back Side | *B | for Standard Roof |
| *C | for Glass Roof | - | - |
| *1 | Glass Primer | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
|---|---|
| a | 9.8 mm (0.386 in.) or more |
| b | 9.6 mm (0.378 in.) or more |
| c | 7.5 mm (0.295 in.) |
| d | 7.3 mm (0.287 in.) |
| e | 9.8 mm (0.386 in.) or more |
| f | 19.0 mm (0.748 in.) or more |
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
Apply glass primer onto the ceramic notches.
If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Apply adhesive to the windshield glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
After cutting off the tip, use all adhesive within the time described in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass as shown in the illustration.
| *A | Back Side | *B | for Standard Roof |
| *C | for Glass Roof | - | - |
| *1 | Adhesive | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 6.6 mm (0.260 in.) |
| c | 8.0 mm (0.315 in.) |
Apply adhesive onto the ceramic notches.
Install the windshield glass.
| *1 | Matchmark |
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass.
Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive onto the windshield glass rim.
Hold the windshield glass using protective tape until applied adhesive becomes hard.
Do not drive the vehicle for the time described in the table below.
| Temperature | Minimum Time prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
9.INSPECT FOR LEAK AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
87810
10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87810
11.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
87818
12.INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror)
13.CONNECT ROOF HEADLINING ASSEMBLY
86468
14.INSTALL LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)
55781E
15.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
55810F
16.INSTALL FRONT VENTILATOR ASSEMBLY
17.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
18.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
85292B
19.INSTALL FRONT WIPER ARM HEAD CAP